Thomas Stöcker
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Thomas Stöcker has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Ralf Moos
University of Bayreuth
4 shared publications - Anna Köhler
Department of Physics, University of Bayreuth, Bayreuth, Germany
1 shared publication D. Hanft
Department of Functional Materials, University of Bayreuth, 95447 Bayreuth, Germany
1 shared publicationD. Schönauer-Kamin
Department of Functional Materials, University of Bayreuth, 95447 Bayreuth, Germany
1 shared publicationG. Hagen
Department of Functional Materials, University of Bayreuth, 95447 Bayreuth, Germany
1 shared publicationGunter Hagen
1 shared publication
Latest Publications
- Open Access
Effect of Oxygen Partial Pressure on the Phase Stability of Copper–Iron Delafossites at Elevated Temperatures
Oxide-based materials are promising candidates for use in high temperature thermoelectric generators. While their thermoelectric performance is inferior to commonly used thermoelectrics, oxides are environmentally friendly and cost-effective. In this study, Cu-based delafossites (CuFeO2), a material class with promising thermoelectric properties at high temperatures, were investigated. This work focuses on the phase stability of CuFeO2 with respect to the temperature and the oxygen partial pressure. For this reason, classical material characterization methods, such as scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction, were combined in order to elucidate the phase composition of delafossites at 900 °C at various oxygen partial pressures. The experimentally obtained results are supported by the theoretical calculation of the Ellingham diagram of the copper–oxygen system. In addition, hot-stage X-ray diffraction and long-term annealing tests of CuFeO2 were performed in order to obtain a holistic review of the phase stability of delafossites at high temperatures and varying oxygen partial pressure. The results support the thermoelectric measurements in previous publications and provide a process window for the use of CuFeO2 in thermoelectric generators.
Open AccessEffect of Oxygen Partial Pressure on the Phase Stability of Copper–Iron Delafossites at Elevated Temperatures
Oxide-based materials are promising candidates for use in high temperature thermoelectric generators. While their thermoelectric performance is inferior to commonly used thermoelectrics, oxides are environmentally friendly and cost-effective. In this study, Cu-based delafossites (CuFeO2), a material class with promising thermoelectric properties at high temperatures, were investigated. This work focuses on the phase stability of CuFeO2 with respect to the temperature and the oxygen partial pressure. For this reason, classical material characterization methods, such as scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction, were combined in order to elucidate the phase composition of delafossites at 900 °C at various oxygen partial pressures. The experimentally obtained results are supported by the theoretical calculation of the Ellingham diagram of the copper–oxygen system. In addition, hot-stage X-ray diffraction and long-term annealing tests of CuFeO2 were performed in order to obtain a holistic review of the phase stability of delafossites at high temperatures and varying oxygen partial pressure. The results support the thermoelectric measurements in previous publications and provide a process window for the use of CuFeO2 in thermoelectric generators.
- 1 March 2018
- Published by Elsevier in Solid State Ionics
- Vol. 316, 1-8
On the defect chemistry of BaFe0.89Al0.01Ta0.1O3‐, a material for temperature independent resistive and thermoelectric oxygen sensors
- 1 March 2018
- Published by Elsevier in Solid State Ionics
- Vol. 316, 1-8
On the defect chemistry of BaFe0.89Al0.01Ta0.1O3‐, a material for temperature independent resistive and thermoelectric oxygen sensors
- Open Access
- 25 September 2014
- Published by Copernicus GmbH in Journal of Sensors and Sensor Systems
- Vol. 3 (2) , 223-229
Aerosol-deposited BaFe0.7Ta0.3O3-δ for nitrogen monoxide and temperature-independent oxygen sensing
The gas sensing properties of resistive gas sensors of BaFe0.7Ta0.3O3-δ (BFT30) prepared by the so-called aerosol deposition method, a method to manufacture dense ceramic films at room temperature, were investigated. The electrical response of the films was investigated first under various oxygen concentrations and in a wide temperature range between 350 and 900 °C. Between 700 and 900 °C, the conductivity of BaFe0.7Ta0.3O3-δ (BFT30) depends on the oxygen concentration with a slope of almost 1/4 in the double-logarithmic plot vs. oxygen partial pressure. In addition, the sensor response is temperature independent. BFT30 responds fast and reproducibly to changing oxygen partial pressures even at 350 °C. The cross-sensitivity has been investigated in environments with various gases (C3H8, NO, NO2, H2, CO, CO2, and H2O) in synthetic air between 350 and 800 °C. BFT30 exhibits good sensing properties to NO between 350 and 400 °C in the range from 1.5 to 2000 ppm with a high selectivity to the other investigated gas species. Thus this semiconducting ceramic material is a good candidate for a temperature-independent oxygen sensor at high temperatures with the application in exhausts and for a selective nitrogen monoxide (NO) sensor at low temperatures for air quality monitoring.
- 25 September 2014
- Published by Copernicus GmbH in Journal of Sensors and Sensor Systems
- Vol. 3 (2) , 223-229
Open AccessAerosol-deposited BaFe0.7Ta0.3O3-δ for nitrogen monoxide and temperature-independent oxygen sensing
The gas sensing properties of resistive gas sensors of BaFe0.7Ta0.3O3-δ (BFT30) prepared by the so-called aerosol deposition method, a method to manufacture dense ceramic films at room temperature, were investigated. The electrical response of the films was investigated first under various oxygen concentrations and in a wide temperature range between 350 and 900 °C. Between 700 and 900 °C, the conductivity of BaFe0.7Ta0.3O3-δ (BFT30) depends on the oxygen concentration with a slope of almost 1/4 in the double-logarithmic plot vs. oxygen partial pressure. In addition, the sensor response is temperature independent. BFT30 responds fast and reproducibly to changing oxygen partial pressures even at 350 °C. The cross-sensitivity has been investigated in environments with various gases (C3H8, NO, NO2, H2, CO, CO2, and H2O) in synthetic air between 350 and 800 °C. BFT30 exhibits good sensing properties to NO between 350 and 400 °C in the range from 1.5 to 2000 ppm with a high selectivity to the other investigated gas species. Thus this semiconducting ceramic material is a good candidate for a temperature-independent oxygen sensor at high temperatures with the application in exhausts and for a selective nitrogen monoxide (NO) sensor at low temperatures for air quality monitoring.
- 14 May 2012
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 50 (14) , 976-983
Why does the electrical conductivity in PEDOT:PSS decrease with PSS content? A study combining thermoelectric measurements with impedance spectroscopy
We have investigated the electrical transport properties of poly(3,4‐ethylenedioxythiophen)/poly(4‐styrene‐sulfonate) (PEDOT:PSS) with PEDOT‐to‐PSS ratios from 1:1 to 1:30. By combining impedance spectroscopy with thermoelectric measurements, we are able to independently determine the variation of electrical conductivity and charge carrier density with PSS content. We find the charge carrier density to be independent of the PSS content. Using a generalized effective media theory, we show that the electrical conductivity in PEDOT:PSS can be understood as percolation between sites of highly conducting PEDOT:PSS complexes with a conductivity of 2.3 (Ωcm)−1 in a matrix of excess PSS with a low conductivity of 10−3 (Ω cm)−1. In addition to the transport properties, the thermoelectric power factors and Seebeck coefficients have been determined. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012
- 14 May 2012
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 50 (14) , 976-983
Why does the electrical conductivity in PEDOT:PSS decrease with PSS content? A study combining thermoelectric measurements with impedance spectroscopy
We have investigated the electrical transport properties of poly(3,4‐ethylenedioxythiophen)/poly(4‐styrene‐sulfonate) (PEDOT:PSS) with PEDOT‐to‐PSS ratios from 1:1 to 1:30. By combining impedance spectroscopy with thermoelectric measurements, we are able to independently determine the variation of electrical conductivity and charge carrier density with PSS content. We find the charge carrier density to be independent of the PSS content. Using a generalized effective media theory, we show that the electrical conductivity in PEDOT:PSS can be understood as percolation between sites of highly conducting PEDOT:PSS complexes with a conductivity of 2.3 (Ωcm)−1 in a matrix of excess PSS with a low conductivity of 10−3 (Ω cm)−1. In addition to the transport properties, the thermoelectric power factors and Seebeck coefficients have been determined. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012