Débora Moraes Duarte
Research Subjects
Débora Moraes Duarte has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Bruno Fructuoso Coelho de Souza
G-Drones. Address: Rua Desembargador do Vale, 653 – São Paulo, São Paulo, Brazil
6 shared publicationsCaiubi Emanuel Souza Kuhn
Center of Applied Natural Sciences (UNESPetro), Institute of Geosciences and Exact Sciences, São Paulo State University – UNESP. Address: Av. 24A, 1555 – Rio Claro, São Paulo, Brazil
6 shared publicationsClaudia Vanessa dos Santos Corrêa
Center of Applied Natural Sciences (UNESPetro), Institute of Geosciences and Exact Sciences, São Paulo State University – UNESP. Address: Av. 24A, 1555 – Rio Claro, São Paulo, Brazil
6 shared publicationsFábio Augusto Gomes Vieira Reis
Center of Applied Natural Sciences (UNESPetro), Institute of Geosciences and Exact Sciences, São Paulo State University – UNESP. Address: Av. 24A, 1555 – Rio Claro, São Paulo, Brazil
6 shared publicationsGeorge A. Longhitano
G-Drones. Address: Rua Desembargador do Vale, 653 – São Paulo, São Paulo, Brazil
6 shared publicationsGuidotti de Souza dos Garion
G-Drones. Address: Rua Desembargador do Vale, 653 – São Paulo, São Paulo, Brazil
6 shared publications
Latest Publications
- Open Access
- 4 October 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-34
Reply on RC1
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- 4 October 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-34
Open AccessReply on RC1
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- Open Access
- 4 October 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-34
Reply on RC2
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- 4 October 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-34
Open AccessReply on RC2
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- Open Access
- 4 August 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-34
Comment on egusphere-2025-1248
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- 4 August 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-34
Open AccessComment on egusphere-2025-1248
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- Open Access
- 31 July 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-34
Comment on egusphere-2025-1248
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- 31 July 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-34
Open AccessComment on egusphere-2025-1248
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- Open Access
- 27 June 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-34
Geological-geotechnical analysis of a rock-toppling prone canyon in Furnas, Brazil, after a fatal event
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- 27 June 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-34
Open AccessGeological-geotechnical analysis of a rock-toppling prone canyon in Furnas, Brazil, after a fatal event
When a disaster related to a natural phenomenon occurs in areas dependent on Geotourism, restoring tourist confidence can be a challenge. An example is the rock-toppling event that occurred on January 2022 in one of the four canyons located in the Furnas reservoir in Brazil, which caused 10 fatalities. Visitation fear and their temporary closure severely impacted the economy of the surrounding municipalities that rely on tourism. To support a safer operation of the canyons to visitation, our study investigates the factors that can lead to landslide events in the region, based on the combination of field investigations, rock-mass quality evaluation (RMR14) and kinematic analysis. We hypothesize that the assessment of rock-mass quality can successfully identify specific areas in the bedrock that are prone to rockfall and rock toppling, supporting risk management strategies in tourist regions. Our results indicate that the 2022 rock-toppling event occurred due to the combination of different factors, such as rainfall infiltration in the unfavorably-oriented joints of the bedrock and reservoir water-level fluctuations. Moreover, the long-term erosion at the base of the slope, caused by the nearby waterfall flow and water-level variations, weakened rock-mass support. The RMR14 method adapted to open rock slopes successfully supports the estimation of the bedrock’s geomechanical properties, identifying structural zones in the rock mass that are prone to slope failure(s) and, as a consequence, should be monitored. The kinematic analysis further indicates that the four canyons are highly susceptible to planar failures and, less so, to toppling, although specific locations in the slopes show a higher rock-toppling susceptibility, especially where two perpendicularly-oriented fault zones (NW-SE and NE-SW strikes) intersect. The consideration of geomechanical properties in hazard evaluation is recommended as a risk management strategy, supporting the delimitation of regions near the rock slopes that should be restricted and of specific portions in the bedrock that should be retained. Our study was fundamental to establishing visitation procedures in the canyons, so that tourists and workers are more protected and aware of the existing geohazards.
- Open Access
- 27 June 2025
- Published by Copernicus GmbH
Supplementary material to "Geological-geotechnical analysis of a rock-toppling prone canyon in Furnas, Brazil, after a fatal event"
- 27 June 2025
- Published by Copernicus GmbH
Open AccessSupplementary material to "Geological-geotechnical analysis of a rock-toppling prone canyon in Furnas, Brazil, after a fatal event"
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Anais da Academia Brasileira de Ciências
- Vol. 94 (suppl 4) , e20210946
Assessing Remotely Piloted Aerial Systems in the characterization of rocky shores for oil spills environmental sensitivity mapping, northern São Paulo littoral, Brazil
The Environmental Sensitivity Index (ESI) for oil spills was developed to assist coordinators to evaluate oil spill impact along shorelines and also to coordinate the allocation of resources during and after the incident, aiming to reduce environmental damage and consequences. Recently, Remotely Piloted Aerial Systems (RPAS) are being used in a wide range of areas, since they complement traditional remote sensing data (e.g., satellite images) and offer a rapidly, precise, detail and high-resolution images that fit well for environmental studies. Herein, the use of high-resolution RPAS images for ESI analysis of rocky shores in the Brazilian territory was performed. Using RPAS images, with their higher-resolution compared with ArcGIS Pro Basemap satellite images, increased the detailed of ESI analysis for oil spills, increasing the number of regions in the rocky shore that are more sensitive to oil spills. The RPAS images were able to decrease the number of areas that were less sensitive to oil spills, and increase areas that are more sensitive to oil spills. This increase is important, since they were not detected in the ESI analysis using conventional ArcGIS Pro Basemap satellite images. The RPAS images permit to delineate precisely rocky shores, improving ESI interpretation in rocky shores.
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Anais da Academia Brasileira de Ciências
- Vol. 94 (suppl 4) , e20210946
Open AccessAssessing Remotely Piloted Aerial Systems in the characterization of rocky shores for oil spills environmental sensitivity mapping, northern São Paulo littoral, Brazil
The Environmental Sensitivity Index (ESI) for oil spills was developed to assist coordinators to evaluate oil spill impact along shorelines and also to coordinate the allocation of resources during and after the incident, aiming to reduce environmental damage and consequences. Recently, Remotely Piloted Aerial Systems (RPAS) are being used in a wide range of areas, since they complement traditional remote sensing data (e.g., satellite images) and offer a rapidly, precise, detail and high-resolution images that fit well for environmental studies. Herein, the use of high-resolution RPAS images for ESI analysis of rocky shores in the Brazilian territory was performed. Using RPAS images, with their higher-resolution compared with ArcGIS Pro Basemap satellite images, increased the detailed of ESI analysis for oil spills, increasing the number of regions in the rocky shore that are more sensitive to oil spills. The RPAS images were able to decrease the number of areas that were less sensitive to oil spills, and increase areas that are more sensitive to oil spills. This increase is important, since they were not detected in the ESI analysis using conventional ArcGIS Pro Basemap satellite images. The RPAS images permit to delineate precisely rocky shores, improving ESI interpretation in rocky shores.