Linqiang Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Linqiang Hu has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Wanjun Lei
Institute of electrical science and technology, Xian Jiaotong University, Xian, China
5 shared publications - Xing Sun
Institute of Electrical Science and Technology Xi'an Jiaotong University Xi'an China
3 shared publications - Jiaqi Zhao
School of Electrical Engineering, Xian Jiaotong University, Xian, Shaanxi, China
2 shared publications - Zhongxiu Xiao
Institute of Electrical Science and Technology Xi'an Jiaotong University Xi'an China
2 shared publications Guoqing Gao
Xian Jiaotong University, Xian, China
1 shared publicationLizi Deng
State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering Xi'an Jiaotong University Xi'an China
1 shared publication
Latest Publications
- 24 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 12 (6) , 5579-5590
An Online Monitoring Method for DC Busbar Electrolytic Capacitor Bank Based on Optimized Rogowski Coil Current Sampling
Distributed energy storage systems (DESS) are now widely used in new energy generation technologies. In order to ensure the reliable and safe operation of the energy storage system, it is necessary to carry out online monitoring of its key connecting unit, the DC stacked busbar electrolytic capacitor bank. This article proposes a design method for an online monitoring system of electrolytic capacitor banks based on optimized Rogowski coil current sampling. By extracting the ripple current and ripple voltage of the electrolytic capacitor under high frequency in real time, so as to calculate the value of ESR of the capacitor, and realize the online monitoring of the working condition of the capacitor. Firstly, in view of the high sampling accuracy requirements of electrolytic capacitor ripple current, the comprehensive consideration of the Rogowski coil winding turns and line width generated by its own impedance and self-inductance on the coil measurement accuracy, optimized the design of a high-precision, small size, strong anti-jamming ability of PCB Rogowski coil, and connected two pieces of coils in series with opposite direction of winding to improve the current sampling accuracy of the coil. Then, on this basis, the monitoring circuit device including embedded current sensor, ripple voltage sampling module, temperature measurement module and self-power supply module is designed. The lower computer processor and upper computer display are designed by software to display the key values of capacitance and carry out reliability evaluation. Finally, the feasibility of the designed monitoring system is verified by experiments. Finally, the feasibility of the designed monitoring system is verified by experiments.
- 24 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 12 (6) , 5579-5590
An Online Monitoring Method for DC Busbar Electrolytic Capacitor Bank Based on Optimized Rogowski Coil Current Sampling
Distributed energy storage systems (DESS) are now widely used in new energy generation technologies. In order to ensure the reliable and safe operation of the energy storage system, it is necessary to carry out online monitoring of its key connecting unit, the DC stacked busbar electrolytic capacitor bank. This article proposes a design method for an online monitoring system of electrolytic capacitor banks based on optimized Rogowski coil current sampling. By extracting the ripple current and ripple voltage of the electrolytic capacitor under high frequency in real time, so as to calculate the value of ESR of the capacitor, and realize the online monitoring of the working condition of the capacitor. Firstly, in view of the high sampling accuracy requirements of electrolytic capacitor ripple current, the comprehensive consideration of the Rogowski coil winding turns and line width generated by its own impedance and self-inductance on the coil measurement accuracy, optimized the design of a high-precision, small size, strong anti-jamming ability of PCB Rogowski coil, and connected two pieces of coils in series with opposite direction of winding to improve the current sampling accuracy of the coil. Then, on this basis, the monitoring circuit device including embedded current sensor, ripple voltage sampling module, temperature measurement module and self-power supply module is designed. The lower computer processor and upper computer display are designed by software to display the key values of capacitance and carry out reliability evaluation. Finally, the feasibility of the designed monitoring system is verified by experiments. Finally, the feasibility of the designed monitoring system is verified by experiments.
- Open Access
- 26 June 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (14) , 1783-1796
Optimal control set expansion method for three‐phase voltage source converter with slip window selection and online parameter modification
Finite control set model predictive control (FCS‐MPC) has been widely used in the control of three‐phase voltage source converter (VSC), but its control performance declines sharply at low sampling frequencies. This paper proposes an optimal control set expansion method with slip window selection and online parameter modification to improve the performance and robustness of FCS‐MPC. First, the performance of different control set expansion methods is compared. Then, an optimal control set expansion method that carries 12 virtual vectors is proposed. Last, a slip window selection strategy and an online parameter modification algorithm are proposed to reduce the computational burden and improve the controller's robustness respectively. Experimental result show that the proposed method significantly improves the control accuracy and carries good robustness and anti‐disturbance ability. Compared with existing typical MPC strategies, the proposed method obtains better current quality with lower switching frequency and requires less calculation. Moreover, the design of the proposed method is simple and there is no weighting factor to be tuned, which increases the method's practicality.
- 26 June 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (14) , 1783-1796
Open AccessOptimal control set expansion method for three‐phase voltage source converter with slip window selection and online parameter modification
Finite control set model predictive control (FCS‐MPC) has been widely used in the control of three‐phase voltage source converter (VSC), but its control performance declines sharply at low sampling frequencies. This paper proposes an optimal control set expansion method with slip window selection and online parameter modification to improve the performance and robustness of FCS‐MPC. First, the performance of different control set expansion methods is compared. Then, an optimal control set expansion method that carries 12 virtual vectors is proposed. Last, a slip window selection strategy and an online parameter modification algorithm are proposed to reduce the computational burden and improve the controller's robustness respectively. Experimental result show that the proposed method significantly improves the control accuracy and carries good robustness and anti‐disturbance ability. Compared with existing typical MPC strategies, the proposed method obtains better current quality with lower switching frequency and requires less calculation. Moreover, the design of the proposed method is simple and there is no weighting factor to be tuned, which increases the method's practicality.
- Open Access
- 24 May 2024
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 18 (10) , 2043-2054
Harmonic impedance optimization scheme for multi‐resonance systems to suppress resonance
Harmonic resonance is caused by harmonic source matching resonance frequency and presents the characteristics of decentralization and whole network in modern grids. The current resonance suppression methods mainly focus on reducing the harmonic source, and are suitable for single‐site and small‐scale grids. This paper presents a new method for suppressing parallel resonance at system level. The holistic harmonic resonance is suppressed by reducing the harmonic impedance. In addition, new resonances are prevented by weakening the coupling between resonance and non‐resonance frequencies. The resonance modal analysis and resonance frequency shift (RFS) are employed to optimize harmonic impedance. Simulation results indicate that the capacitance parameter has higher sensitivity and is theoretically more suitable for RFS. Considering the accuracy of modal frequency sensitivity, a variable‐limit genetic algorithm for iteration is proposed. The validity of the proposed method was verified using an IEEE 14‐bus test network.
- 24 May 2024
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 18 (10) , 2043-2054
Open AccessHarmonic impedance optimization scheme for multi‐resonance systems to suppress resonance
Harmonic resonance is caused by harmonic source matching resonance frequency and presents the characteristics of decentralization and whole network in modern grids. The current resonance suppression methods mainly focus on reducing the harmonic source, and are suitable for single‐site and small‐scale grids. This paper presents a new method for suppressing parallel resonance at system level. The holistic harmonic resonance is suppressed by reducing the harmonic impedance. In addition, new resonances are prevented by weakening the coupling between resonance and non‐resonance frequencies. The resonance modal analysis and resonance frequency shift (RFS) are employed to optimize harmonic impedance. Simulation results indicate that the capacitance parameter has higher sensitivity and is theoretically more suitable for RFS. Considering the accuracy of modal frequency sensitivity, a variable‐limit genetic algorithm for iteration is proposed. The validity of the proposed method was verified using an IEEE 14‐bus test network.
- 23 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (7) , 6918-6928
Optimal Weighting Factor Design of Finite Control Set Model Predictive Control Based on Multiobjective Ant Colony Optimization
In this article, an improved multiobjective ant colony optimization (ACO) algorithm is proposed to design the weighting factors (WFs) in the model predictive control of power converters. First, the principle of the multiobjective ACO algorithm is introduced. Then, the WF design process based on the multiobjective ACO algorithm is given in both the single-function mode and the Pareto mode. Finally, improvement measures are proposed for the multiobjective ACO algorithm to reduce the calculation and accelerate the convergence. Simulations and experiments are carried out on a parallel three-level dc–dc converter. The results show that the proposed method is faster and less-computational than the traditional ACO algorithm, and is more accurate than the particle swarm optimization algorithm. With the proposed method, higher solution diversity and smaller control error can be achieved. In addition, the proposed method can also be used for WF online tuning, which will bring more benefits when the converter parameters are mismatched.
- 23 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (7) , 6918-6928
Optimal Weighting Factor Design of Finite Control Set Model Predictive Control Based on Multiobjective Ant Colony Optimization
In this article, an improved multiobjective ant colony optimization (ACO) algorithm is proposed to design the weighting factors (WFs) in the model predictive control of power converters. First, the principle of the multiobjective ACO algorithm is introduced. Then, the WF design process based on the multiobjective ACO algorithm is given in both the single-function mode and the Pareto mode. Finally, improvement measures are proposed for the multiobjective ACO algorithm to reduce the calculation and accelerate the convergence. Simulations and experiments are carried out on a parallel three-level dc–dc converter. The results show that the proposed method is faster and less-computational than the traditional ACO algorithm, and is more accurate than the particle swarm optimization algorithm. With the proposed method, higher solution diversity and smaller control error can be achieved. In addition, the proposed method can also be used for WF online tuning, which will bring more benefits when the converter parameters are mismatched.
- 26 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (4) , 4475-4492
Dual-Terminal Voltage Feedforward Based Direct Power Control Scheme and Stability Analysis of Dual Active Bridge Converter in DC Microgrid Systems
The dual active bridge (DAB) dc-dc converter plays an important role in energy exchange between DC microgrids integrated with energy storage systems. To directly control the power flow between the adjacent DC microgrids rapidly and accurately, a dual-terminal voltage feedforward based direct power control scheme (DVF-DPC) with single-phase-shift control is proposed for the DAB dc-dc converter. The strategy makes the converter realize rapid and precise output power regulation under the following conditions, including the start-up process, load step-change, the desired output power step-change, and voltage fluctuations. An accurate discrete-time model is applied to analyze the system's dynamic characteristics, and a discrete-time small-signal model of the system is established to design the controller's parameters. In addition, a comprehensive and systematic analysis of all the possible unstable phenomena for adjacent DC microgrids is conducted based on the discrete-time model. Accordingly, the underlying mechanisms are revealed by analyzing the relationships among the state variables, the Floquet multipliers, and system parameters. Hence, the stability-oriented parameter design method is given which can provide guidance in practice. The theoretical analysis is verified in both the time domain and frequency domain. Finally, by comparing the DVF-DPC method with the traditional PI feedback control, the superiority of the proposed strategy is verified through theoretical analysis and experimental results, which demonstrates its application prospect in the field of electric energy dispatch control of the DC power supply network.
- 26 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (4) , 4475-4492
Dual-Terminal Voltage Feedforward Based Direct Power Control Scheme and Stability Analysis of Dual Active Bridge Converter in DC Microgrid Systems
The dual active bridge (DAB) dc-dc converter plays an important role in energy exchange between DC microgrids integrated with energy storage systems. To directly control the power flow between the adjacent DC microgrids rapidly and accurately, a dual-terminal voltage feedforward based direct power control scheme (DVF-DPC) with single-phase-shift control is proposed for the DAB dc-dc converter. The strategy makes the converter realize rapid and precise output power regulation under the following conditions, including the start-up process, load step-change, the desired output power step-change, and voltage fluctuations. An accurate discrete-time model is applied to analyze the system's dynamic characteristics, and a discrete-time small-signal model of the system is established to design the controller's parameters. In addition, a comprehensive and systematic analysis of all the possible unstable phenomena for adjacent DC microgrids is conducted based on the discrete-time model. Accordingly, the underlying mechanisms are revealed by analyzing the relationships among the state variables, the Floquet multipliers, and system parameters. Hence, the stability-oriented parameter design method is given which can provide guidance in practice. The theoretical analysis is verified in both the time domain and frequency domain. Finally, by comparing the DVF-DPC method with the traditional PI feedback control, the superiority of the proposed strategy is verified through theoretical analysis and experimental results, which demonstrates its application prospect in the field of electric energy dispatch control of the DC power supply network.
- 5 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (2) , 1661-1671
A Graphic Weighting Factor Design Method for Finite Control Set Model Predictive Control of Power Converters
Finite control set model predictive control (FCS-MPC) has been widely used in the control of power converters. However, for converters with multiple optimization objectives, the design of the weighting factors in the cost function is a tricky problem. To solve the weighting factor design problem in multiobjective FCS-MPC, a graphic weighing factor design method is proposed in this paper. Firstly, the discrete control variables are taken into the prediction model to determine the state boundaries of each control objective under all the system states. Then, the priorities and weighting factors of the control objectives are determined and designed by adjusting the intersection area of these state boundaries, so as to optimize the system performance. Finally, the operating condition feedback is introduced to realize an adaptive adjusting of the weighting factors so that the relationship of the state boundaries between different control objectives will not be affected by the change of system operating condition, and the controller robustness can be guaranteed. Analysis and experiment are carried out based on the parallel three-level DC-DC system. The results show that the proposed method can effectively solve the weighting factor design problem of multiobjective FCS-MPC. It is simple, efficient, and robust.
- 5 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 11 (2) , 1661-1671
A Graphic Weighting Factor Design Method for Finite Control Set Model Predictive Control of Power Converters
Finite control set model predictive control (FCS-MPC) has been widely used in the control of power converters. However, for converters with multiple optimization objectives, the design of the weighting factors in the cost function is a tricky problem. To solve the weighting factor design problem in multiobjective FCS-MPC, a graphic weighing factor design method is proposed in this paper. Firstly, the discrete control variables are taken into the prediction model to determine the state boundaries of each control objective under all the system states. Then, the priorities and weighting factors of the control objectives are determined and designed by adjusting the intersection area of these state boundaries, so as to optimize the system performance. Finally, the operating condition feedback is introduced to realize an adaptive adjusting of the weighting factors so that the relationship of the state boundaries between different control objectives will not be affected by the change of system operating condition, and the controller robustness can be guaranteed. Analysis and experiment are carried out based on the parallel three-level DC-DC system. The results show that the proposed method can effectively solve the weighting factor design problem of multiobjective FCS-MPC. It is simple, efficient, and robust.