Zhenfei Lv
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhenfei Lv has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Xiulin Shen
School of Materials Science and Engineering, Anhui University of Science and Technology, Huainan 232001, China
6 shared publications Chong Lan
5 shared publicationsMengke Fan
5 shared publicationsXiulin Shen
5 shared publicationsYukun Cao
4 shared publications- Junchi Weng
School of Materials Science and Engineering, Anhui University of Science and Technology, Huainan 232001, China
3 shared publications
Latest Publications
- Open Access
Fabrication of High-Performance Porous Thermal Insulating Ceramics via High-Proportion Utilization of Industrial Solid Wastes
Large-scale high-value utilization of industrial solid waste is urgently required worldwide. Porous ceramics prepared from single-type solid waste face great limitations in balancing mechanical properties and thermal insulation performance. In this work, various types of industrial solid wastes—red mud, waste electric porcelain, and coal gangue—were fully adopted as primary raw materials, while SiC was employed as a foaming agent to prepare porous ceramics. Results show that at 3% SiC addition and 1140 °C sintering temperature, the apparent porosity of the ceramics reaches to 21.8%, with thermal conductivity of 0.08 W/(m·K). Moreover, favorable pore-size distribution and desirable crystalline phases (Mg–Fe–Al spinel and sodium calcium feldspar) are obtained under this optimal condition, accompanied by a favorable compressive strength of 2.91 MPa, making it a promising low-cost, high-performance high-temperature insulation material.
Open AccessFabrication of High-Performance Porous Thermal Insulating Ceramics via High-Proportion Utilization of Industrial Solid Wastes
Large-scale high-value utilization of industrial solid waste is urgently required worldwide. Porous ceramics prepared from single-type solid waste face great limitations in balancing mechanical properties and thermal insulation performance. In this work, various types of industrial solid wastes—red mud, waste electric porcelain, and coal gangue—were fully adopted as primary raw materials, while SiC was employed as a foaming agent to prepare porous ceramics. Results show that at 3% SiC addition and 1140 °C sintering temperature, the apparent porosity of the ceramics reaches to 21.8%, with thermal conductivity of 0.08 W/(m·K). Moreover, favorable pore-size distribution and desirable crystalline phases (Mg–Fe–Al spinel and sodium calcium feldspar) are obtained under this optimal condition, accompanied by a favorable compressive strength of 2.91 MPa, making it a promising low-cost, high-performance high-temperature insulation material.
- Open Access
Research on the Development Method and Adsorptive Characteristics of Lightweight and High-Strength Ceramsite Produced from Coal Gangue
The prolonged outdoor storage of coal gangue leads to significant environmental issues, while the contamination of water by antibiotics poses a worldwide health concern. Conventional adsorbents are often hindered by their expense and fragility. Current studies on ceramsite derived from coal gangue have not successfully combined the repurposing of solid waste with the management of water pollution. This research utilized coal gangue and waste electric porcelain as primary materials, incorporating 2 wt.% calcium carbonate as a foaming agent, and produced ceramsite through a gradient-heating sintering process. The investigation thoroughly examined how sintering temperature and particle size distribution influenced the material’s performance. Findings indicated that mullite-based ceramsite, sintered at 1400 °C for 15 min, achieved an apparent porosity of 35.68% and a compressive strength of 10.03 MPa. A particle size distribution following a normal model resulted in a 7.9% removal efficiency of 20.00 mg/L tetracycline hydrochloride in just 30 min, with a minimal post-adsorption strength decrease of 3.7%. This study offers a theoretical framework and practical guidance for the effective utilization of coal gangue and the economical treatment of antibiotic-laden wastewater.
Open AccessResearch on the Development Method and Adsorptive Characteristics of Lightweight and High-Strength Ceramsite Produced from Coal Gangue
The prolonged outdoor storage of coal gangue leads to significant environmental issues, while the contamination of water by antibiotics poses a worldwide health concern. Conventional adsorbents are often hindered by their expense and fragility. Current studies on ceramsite derived from coal gangue have not successfully combined the repurposing of solid waste with the management of water pollution. This research utilized coal gangue and waste electric porcelain as primary materials, incorporating 2 wt.% calcium carbonate as a foaming agent, and produced ceramsite through a gradient-heating sintering process. The investigation thoroughly examined how sintering temperature and particle size distribution influenced the material’s performance. Findings indicated that mullite-based ceramsite, sintered at 1400 °C for 15 min, achieved an apparent porosity of 35.68% and a compressive strength of 10.03 MPa. A particle size distribution following a normal model resulted in a 7.9% removal efficiency of 20.00 mg/L tetracycline hydrochloride in just 30 min, with a minimal post-adsorption strength decrease of 3.7%. This study offers a theoretical framework and practical guidance for the effective utilization of coal gangue and the economical treatment of antibiotic-laden wastewater.
- 4 June 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (19) , 35337-35350
Enhanced corrosion resistance of electrical porcelain saggars using a gradient-structured layer derived from industrial solid wastes
- 4 June 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (19) , 35337-35350
Enhanced corrosion resistance of electrical porcelain saggars using a gradient-structured layer derived from industrial solid wastes
- 5 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (2) , 2392-2402
Integrated MnFe2O4 nanoparticles on waste-derived N-doped porous carbon for enhanced electromagnetic wave absorption
- 5 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (2) , 2392-2402
Integrated MnFe2O4 nanoparticles on waste-derived N-doped porous carbon for enhanced electromagnetic wave absorption
- 13 October 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (28) , 59239-59251
Effect of potassium feldspar dosage and sintering temperature on the properties of saggar derived from waste ceramic for calcination of ternary lithium-ion batteries cathode materials
- 13 October 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (28) , 59239-59251
Effect of potassium feldspar dosage and sintering temperature on the properties of saggar derived from waste ceramic for calcination of ternary lithium-ion batteries cathode materials
- Open Access
Low-Cost Foamed Ceramics with Enhanced Mechanical Performance and Uniform Pore Size Structure
Due to the lack of effective utilization, fly ash and red mud accumulate in large quantities and cause serious harm to the environment. In this experiment, a low-cost preparation of foamed ceramics was realized by applying the foaming agent addition method using fly ash and red mud. The results indicated that temperature and foaming agent content significantly affected the macrostructure, microstructure, crystalline phases, and properties of the foamed ceramics. Specifically, a formulation comprising 45 wt.% fly ash, 45 wt.% red mud, 10 wt.% clay, and 1 wt.% SiC (addition), sintered at 1210 °C, yielded a compressive strength of 8.2 MPa, a bulk density of 1.17 g/cm3, a water absorption rate of 32.05%, and an apparent porosity of 37.59%. The as-prepared materials demonstrate potential as cost-effective building materials, putting forward an effective approach for the high-value utilization of fly ash and red mud.
Open AccessLow-Cost Foamed Ceramics with Enhanced Mechanical Performance and Uniform Pore Size Structure
Due to the lack of effective utilization, fly ash and red mud accumulate in large quantities and cause serious harm to the environment. In this experiment, a low-cost preparation of foamed ceramics was realized by applying the foaming agent addition method using fly ash and red mud. The results indicated that temperature and foaming agent content significantly affected the macrostructure, microstructure, crystalline phases, and properties of the foamed ceramics. Specifically, a formulation comprising 45 wt.% fly ash, 45 wt.% red mud, 10 wt.% clay, and 1 wt.% SiC (addition), sintered at 1210 °C, yielded a compressive strength of 8.2 MPa, a bulk density of 1.17 g/cm3, a water absorption rate of 32.05%, and an apparent porosity of 37.59%. The as-prepared materials demonstrate potential as cost-effective building materials, putting forward an effective approach for the high-value utilization of fly ash and red mud.
- Open Access
Enhanced Mechanical and Thermal Properties of Waste Electric Porcelain-Based Solar Energy-Absorbing Thermal Storage Ceramics with Interwoven Mullite Structure
This study addresses the environmental and resource challenges posed by the growing volume of waste electric porcelain in the power industry by developing solar absorption and thermal storage integrated ceramics (SATS ceramics) from waste electric porcelain. These SATS ceramics, which feature an exceptional mullite structure, were crafted through the optimization of the sintering process. Notably, when sintered at 1400 °C with an 11 wt.% magnetite content, the resulting material boasts an optimal short-clustered, ordered, and interwoven columnar mullite structure. This structure endows the material with a remarkable flexural strength of 96.05 MPa and a specific heat capacity of up to 0.6415 J/(g* °C) at 300 °C, significantly enhancing its thermal energy storage efficiency. This research offers innovative insights into the high-value utilization of waste electric porcelain and the development of solar thermal storage materials, underscoring its significant environmental and economic advantages.
Open AccessEnhanced Mechanical and Thermal Properties of Waste Electric Porcelain-Based Solar Energy-Absorbing Thermal Storage Ceramics with Interwoven Mullite Structure
This study addresses the environmental and resource challenges posed by the growing volume of waste electric porcelain in the power industry by developing solar absorption and thermal storage integrated ceramics (SATS ceramics) from waste electric porcelain. These SATS ceramics, which feature an exceptional mullite structure, were crafted through the optimization of the sintering process. Notably, when sintered at 1400 °C with an 11 wt.% magnetite content, the resulting material boasts an optimal short-clustered, ordered, and interwoven columnar mullite structure. This structure endows the material with a remarkable flexural strength of 96.05 MPa and a specific heat capacity of up to 0.6415 J/(g* °C) at 300 °C, significantly enhancing its thermal energy storage efficiency. This research offers innovative insights into the high-value utilization of waste electric porcelain and the development of solar thermal storage materials, underscoring its significant environmental and economic advantages.
- 25 September 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (23) , 49698-49711
Waste electric porcelain-based refractory bricks with significantly enhanced mechanical properties: Preparation, characterization and mechanism
- 25 September 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (23) , 49698-49711
Waste electric porcelain-based refractory bricks with significantly enhanced mechanical properties: Preparation, characterization and mechanism
- 8 August 2024
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 22 (1)
Property dependence on particle size and sintering temperature of waste porcelain high‐temperature resistant material
The rapid development of the power industry has resulted in a significant amount of electric porcelain solid waste. To address the challenges of small‐scale utilization and low added value associated with the current utilization of porcelain solid waste, a new high‐temperature resistant material was successfully developed using waste electric porcelain with varying particle sizes as the primary raw material. The dependence of composition, structure, and mechanical properties on fine particle size and sintering temperature was explored. The research has determined that the most effective particle size for the synthesis of refractory materials using waste electric porcelain is 120 mesh, and the optimal temperature is 1600°C. When the temperature exceeds 1500°C, the expansion generated by the decomposition of sillimanite will counteract the shrinkage of the liquid phase reaction, thereby maintaining the morphology of the sample. This process forms a unique interwoven mullite morphology through the decomposition of sillimanite, thereby enhancing the strength of the material. As a result, the optimal bending strength of 74 MPa and the optimal compression strength of 207 MPa were obtained. The realization of high‐temperature resistant materials based on discarded electric porcelain has shown foreseeable potential in large‐scale high‐value utilization.
- 8 August 2024
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 22 (1)
Property dependence on particle size and sintering temperature of waste porcelain high‐temperature resistant material
The rapid development of the power industry has resulted in a significant amount of electric porcelain solid waste. To address the challenges of small‐scale utilization and low added value associated with the current utilization of porcelain solid waste, a new high‐temperature resistant material was successfully developed using waste electric porcelain with varying particle sizes as the primary raw material. The dependence of composition, structure, and mechanical properties on fine particle size and sintering temperature was explored. The research has determined that the most effective particle size for the synthesis of refractory materials using waste electric porcelain is 120 mesh, and the optimal temperature is 1600°C. When the temperature exceeds 1500°C, the expansion generated by the decomposition of sillimanite will counteract the shrinkage of the liquid phase reaction, thereby maintaining the morphology of the sample. This process forms a unique interwoven mullite morphology through the decomposition of sillimanite, thereby enhancing the strength of the material. As a result, the optimal bending strength of 74 MPa and the optimal compression strength of 207 MPa were obtained. The realization of high‐temperature resistant materials based on discarded electric porcelain has shown foreseeable potential in large‐scale high‐value utilization.
- 3 August 2024
- Published by Springer Nature in Carbon Letters
- Vol. 35 (1) , 235-244
One-step preparation of N-doped porous carbon materials with excellent microwave absorption properties based on methylene blue saturated wood-based activated carbon
- 3 August 2024
- Published by Springer Nature in Carbon Letters
- Vol. 35 (1) , 235-244
One-step preparation of N-doped porous carbon materials with excellent microwave absorption properties based on methylene blue saturated wood-based activated carbon