Pavel P. Dik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pavel P. Dik has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Alexander S. Noskov
Boreskov Institute of Catalysis SB RAS
7 shared publications - Ivan S. Golubev
Boreskov Institute of Catalysis, Siberian Branch, Russian Academy of Sciences, Novosibirsk, Russia
6 shared publications - Ivan A. Mik
Boreskov Institute of Catalysis SB RAS
4 shared publications - Roman V. Petrov
Russian Academy of Sciences
4 shared publications - Sergey Ivanovich Reshetnikov
Boreskov Institute of Catalysis SB RAS
3 shared publications - Evgeniy Yu. Gerasimov
Boreskov Institute of Catalysis
2 shared publications
Latest Publications
- 3 November 2026
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 16 (21) , 7264-7276
Tuning catalyst performance for second-stage hydrocracking via USY zeolite combination
The effect of combining two ultrastable Y (USY) zeolites (Y1 and Y2) with different acidities on the performance of NiW/Y catalysts in second-stage hydrocracking was investigated.
- 3 November 2026
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 16 (21) , 7264-7276
Tuning catalyst performance for second-stage hydrocracking via USY zeolite combination
The effect of combining two ultrastable Y (USY) zeolites (Y1 and Y2) with different acidities on the performance of NiW/Y catalysts in second-stage hydrocracking was investigated.
- 10 August 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (33) , 18498-18508
Sulfated Alumina Aerogels: Effect of the Sulfur Introduction Method on the Catalytic Performance in Acid-Catalyzed Reactions
The goal of this study was to prepare sulfated alumina aerogels and investigate their textural properties, morphology, acidity, and catalytic activity in ethanol dehydration and esterification of decanoic acid with methanol. Alumina aerogels were synthesized by hydrolysis of an aluminum isopropoxide solution in isopropanol followed by supercritical drying in an autoclave at 265 °C. For the synthesis of sulfated alumina aerogels, sulfuric acid was either introduced into the solution prior to hydrolysis and formation of the gels or added by incipient wetness impregnation of the alumina aerogel calcined at 550 °C using an H2SO4 solution in ethanol. Sulfated alumina aerogels prepared by solution modification with H2SO4 had significantly higher concentrations of weak electron-acceptor sites compared to pure alumina. The catalytic activity of the prepared aerogels was tested in two catalytic reactions taking place on surface acid sites: ethanol dehydration and esterification of decanoic acid with methanol. Only the sample prepared by impregnation showed high catalytic activity in both studied reactions. This sample also had a substantially higher concentration of Br nsted acid sites measured by Fourier-transform infrared (FTIR) after adsorption of pyridine. So, it appears to be a promising acid catalyst with high surface area and high acidity.
- 10 August 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (33) , 18498-18508
Sulfated Alumina Aerogels: Effect of the Sulfur Introduction Method on the Catalytic Performance in Acid-Catalyzed Reactions
The goal of this study was to prepare sulfated alumina aerogels and investigate their textural properties, morphology, acidity, and catalytic activity in ethanol dehydration and esterification of decanoic acid with methanol. Alumina aerogels were synthesized by hydrolysis of an aluminum isopropoxide solution in isopropanol followed by supercritical drying in an autoclave at 265 °C. For the synthesis of sulfated alumina aerogels, sulfuric acid was either introduced into the solution prior to hydrolysis and formation of the gels or added by incipient wetness impregnation of the alumina aerogel calcined at 550 °C using an H2SO4 solution in ethanol. Sulfated alumina aerogels prepared by solution modification with H2SO4 had significantly higher concentrations of weak electron-acceptor sites compared to pure alumina. The catalytic activity of the prepared aerogels was tested in two catalytic reactions taking place on surface acid sites: ethanol dehydration and esterification of decanoic acid with methanol. Only the sample prepared by impregnation showed high catalytic activity in both studied reactions. This sample also had a substantially higher concentration of Br nsted acid sites measured by Fourier-transform infrared (FTIR) after adsorption of pyridine. So, it appears to be a promising acid catalyst with high surface area and high acidity.
- Open Access
- 9 October 2025
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 12 (4) , 9072
Evaluation of particle size effect on two-phase flow distribution in a hydrotreatment reactor guard bed using particle-resolved CFD simulations
Trickle bed reactors with solid catalyst pellets are important and widely used large-scale apparatuses in the chemical and oil refining industries. In order to reduce the effects of poisons on the catalyst bed and to extend the catalyst loading service life as much as possible, guard beds are loaded onto the main catalyst bed, intended for deposition of fine impurities on them, conversion, binding of catalytic poisons and distribution flow. In this research, realistic loadings of guard bed catalyst pellets were constructed. We demonstrated that the process of studying the features of the hydrodynamic structure of the flow proposed in this work can be used to investigate the flow distribution and hydrodynamic resistance in hydroprocessing reactors. The particles are considered to be Raschig Rings 8 and 16 mm (outer diameter and height) with wall thickness of 1, 2 and 3 mm. The effect of particle size on flow distribution was studied using the standard deviation criterion. Based on this criterion, it was found that the loading of Raschig rings with wall thickness of 1 mm is optimal.
- 9 October 2025
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 12 (4) , 9072
Open AccessEvaluation of particle size effect on two-phase flow distribution in a hydrotreatment reactor guard bed using particle-resolved CFD simulations
Trickle bed reactors with solid catalyst pellets are important and widely used large-scale apparatuses in the chemical and oil refining industries. In order to reduce the effects of poisons on the catalyst bed and to extend the catalyst loading service life as much as possible, guard beds are loaded onto the main catalyst bed, intended for deposition of fine impurities on them, conversion, binding of catalytic poisons and distribution flow. In this research, realistic loadings of guard bed catalyst pellets were constructed. We demonstrated that the process of studying the features of the hydrodynamic structure of the flow proposed in this work can be used to investigate the flow distribution and hydrodynamic resistance in hydroprocessing reactors. The particles are considered to be Raschig Rings 8 and 16 mm (outer diameter and height) with wall thickness of 1, 2 and 3 mm. The effect of particle size on flow distribution was studied using the standard deviation criterion. Based on this criterion, it was found that the loading of Raschig rings with wall thickness of 1 mm is optimal.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Нефтехимия / Petroleum Chemistry
- Vol. 65 (6) , 491
Зависимость физико-химических и каталитических свойств Ni–Mo/AlO-катализатора защитного слоя от сорбции кремния в процессе гидроочистки дизельной фракции
Изучено влияние сорбции кремния в процессе гидроочистки дизельной фракции на физико-химические и каталитические свойства NiMo/AlO-катализатора защитного слоя. Физико-химические характеристики катализаторов исследовали методами низкотемпературной адсорбции азота, термогравиметрическим анализом (ТГА), рентгеновской фотоэлектронной спектроскопией (РФЭС) и атомно-эмиссионной спектроскопией с индуктивно-связанной плазмой (АЭС-ИСП). Установлено, что содержание кремния на поверхности катализатора выше, чем в его объеме. Выявлена линейная зависимость снижения объема пор и удельной поверхности катализатора от количества сорбированного кремния (до 5 мас.%). Получены количественные оценки температуры, необходимой для компенсации активности катализатора от содержания кремния в образце. Показана возрастающая нелинейная зависимость потери активности катализатора от содержания кремния.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Нефтехимия / Petroleum Chemistry
- Vol. 65 (6) , 491
Зависимость физико-химических и каталитических свойств Ni–Mo/AlO-катализатора защитного слоя от сорбции кремния в процессе гидроочистки дизельной фракции
Изучено влияние сорбции кремния в процессе гидроочистки дизельной фракции на физико-химические и каталитические свойства NiMo/AlO-катализатора защитного слоя. Физико-химические характеристики катализаторов исследовали методами низкотемпературной адсорбции азота, термогравиметрическим анализом (ТГА), рентгеновской фотоэлектронной спектроскопией (РФЭС) и атомно-эмиссионной спектроскопией с индуктивно-связанной плазмой (АЭС-ИСП). Установлено, что содержание кремния на поверхности катализатора выше, чем в его объеме. Выявлена линейная зависимость снижения объема пор и удельной поверхности катализатора от количества сорбированного кремния (до 5 мас.%). Получены количественные оценки температуры, необходимой для компенсации активности катализатора от содержания кремния в образце. Показана возрастающая нелинейная зависимость потери активности катализатора от содержания кремния.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Теоретические основы химической технологии / Theoretical Foundations of Chemical Engineering
- Vol. 59 (6) , 16-24
Testing Adsorption Properties of the NiMo/AlO Catalyst of the Protective Layer during Hydrotreatment of Diesel Fuel with a High Silicon Content
Experiments with a duration of 60 and 200 hours are carried out at different contact times of 0.33, 0.66, and 1.33 hours (the specific volumetric rate is 3.0, 1.5, and 0.75 h, and the pressure is 4.0 MPa) during hydrotreatment of diesel fuel with a high silicon content. Experiments with a run time of 200 hours showed that the silicon concentration in the front layer of the NiMo/AlO catalyst does not change as the contact time grows, indicating that the maximum capacity value of ~5 wt. % is reached. The absence of the influence of external mass transfer on the adsorption of silicon, as well as on the conversion of sulfur during testing of the catalyst in a laboratory setup, is experimentally studied and theoretically substantiated. The values of linear feed rates of raw materials are determined, showing no influence of external mass transfer on both the process of silicon adsorption and sulfur conversion.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Теоретические основы химической технологии / Theoretical Foundations of Chemical Engineering
- Vol. 59 (6) , 16-24
Testing Adsorption Properties of the NiMo/AlO Catalyst of the Protective Layer during Hydrotreatment of Diesel Fuel with a High Silicon Content
Experiments with a duration of 60 and 200 hours are carried out at different contact times of 0.33, 0.66, and 1.33 hours (the specific volumetric rate is 3.0, 1.5, and 0.75 h, and the pressure is 4.0 MPa) during hydrotreatment of diesel fuel with a high silicon content. Experiments with a run time of 200 hours showed that the silicon concentration in the front layer of the NiMo/AlO catalyst does not change as the contact time grows, indicating that the maximum capacity value of ~5 wt. % is reached. The absence of the influence of external mass transfer on the adsorption of silicon, as well as on the conversion of sulfur during testing of the catalyst in a laboratory setup, is experimentally studied and theoretically substantiated. The values of linear feed rates of raw materials are determined, showing no influence of external mass transfer on both the process of silicon adsorption and sulfur conversion.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Журнал прикладной химии / Russian Journal of Applied Chemistry
- Vol. 98 (9-10) , 523-532
ИССЛЕДОВАНИЕ СОРБЦИИ КРЕМНИЯ НА КАТАЛИЗАТОРАХ ЗАЩИТНОГО СЛОЯ В ПРОЦЕССЕ ГИДРООЧИСТКИ ДИЗЕЛЬНОГО ТОПЛИВА
Проведено тестирование двух синтезированных Ni-Mo катализаторов защитного слоя (K3C-1, K3C-2), различающихся текстурными характеристиками и, в качестве сравнения, одного Co-Mo промышленного катализатора основного слоя (KOC-1) в процессе гидроочистки дизельного топлива с повышенной концентрацией кремния (200 ppm). Физико-химические характеристики катализаторов до и после процесса гидроочистки исследовали методами низкотемпературной адсорбции азота, РФЭС и атомно-эмиссионной спектроскопии с индуктивно-связанной плазмой. Сделан оценка максимальной (статической) емкости по кремнию и времени защитного действия слоя катализатора. Показано, что активность в реакциях превращения серы и азота для исследованных катализаторов снижается в ряду KOC-1 > K3C-1 > K3C-2, а адсорбционные свойства по отношению к кремнию близки. На основе зависимости каталитических и адсорбционных свойств катализаторов сделан вывод, что использование высокоактивных катализаторов в защитных слоях неэффективно ввиду значительной потери их активности в результате дезактивации загрязняющими веществами, в частности кремнием.
- 1 January 2025
- Published by Akademizdatcenter Nauka in Журнал прикладной химии / Russian Journal of Applied Chemistry
- Vol. 98 (9-10) , 523-532
ИССЛЕДОВАНИЕ СОРБЦИИ КРЕМНИЯ НА КАТАЛИЗАТОРАХ ЗАЩИТНОГО СЛОЯ В ПРОЦЕССЕ ГИДРООЧИСТКИ ДИЗЕЛЬНОГО ТОПЛИВА
Проведено тестирование двух синтезированных Ni-Mo катализаторов защитного слоя (K3C-1, K3C-2), различающихся текстурными характеристиками и, в качестве сравнения, одного Co-Mo промышленного катализатора основного слоя (KOC-1) в процессе гидроочистки дизельного топлива с повышенной концентрацией кремния (200 ppm). Физико-химические характеристики катализаторов до и после процесса гидроочистки исследовали методами низкотемпературной адсорбции азота, РФЭС и атомно-эмиссионной спектроскопии с индуктивно-связанной плазмой. Сделан оценка максимальной (статической) емкости по кремнию и времени защитного действия слоя катализатора. Показано, что активность в реакциях превращения серы и азота для исследованных катализаторов снижается в ряду KOC-1 > K3C-1 > K3C-2, а адсорбционные свойства по отношению к кремнию близки. На основе зависимости каталитических и адсорбционных свойств катализаторов сделан вывод, что использование высокоактивных катализаторов в защитных слоях неэффективно ввиду значительной потери их активности в результате дезактивации загрязняющими веществами, в частности кремнием.
- 25 November 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (23) , 23068-23082
Silica Gel─A Perspective Component to Increase Catalyst Activity in FCC Gasoline Hydrotreatment
- 25 November 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (23) , 23068-23082
Silica Gel─A Perspective Component to Increase Catalyst Activity in FCC Gasoline Hydrotreatment
- Open Access
- 22 November 2024
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 11 (4) , 202411416
Influence of feedstock composition on the pressure drop buildup in gas oil hydrotreater
In this work two samples of solid particulates obtained from the intergranular space of the guard beds catalyst of industrial gas oil hydrotreating reactors were investigated. The hydrotreating reactors were operated on feedstock of different composition. One of the samples of solid particulates was obtained during hydrotreating of feedstock containing a large amount of sodium and calcium. The compositions of the samples of solid particulates were determined. Quantitative elemental and structural analyses were carried out. As a result, the formed solid particulates contained a large amount of sodium chloride, sulfate and calcium sulfide. The qualitative calculations show that the pressure drop in the guard bed of five-segment rings with a diameter of 16.0 mm, due to the deposition of solid particulates in the intergranular space, increases by 108% more than the pressure drop during hydrotreating of feedstock not containing calcium and sodium compounds (under the same operating modes of the hydrotreating reactors and operating time). The obtained results on the effect of the feedstock composition on the pressure drop buildup can be used in optimizing the loading of reactors and in other oil refining processes.
- 22 November 2024
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 11 (4) , 202411416
Open AccessInfluence of feedstock composition on the pressure drop buildup in gas oil hydrotreater
In this work two samples of solid particulates obtained from the intergranular space of the guard beds catalyst of industrial gas oil hydrotreating reactors were investigated. The hydrotreating reactors were operated on feedstock of different composition. One of the samples of solid particulates was obtained during hydrotreating of feedstock containing a large amount of sodium and calcium. The compositions of the samples of solid particulates were determined. Quantitative elemental and structural analyses were carried out. As a result, the formed solid particulates contained a large amount of sodium chloride, sulfate and calcium sulfide. The qualitative calculations show that the pressure drop in the guard bed of five-segment rings with a diameter of 16.0 mm, due to the deposition of solid particulates in the intergranular space, increases by 108% more than the pressure drop during hydrotreating of feedstock not containing calcium and sodium compounds (under the same operating modes of the hydrotreating reactors and operating time). The obtained results on the effect of the feedstock composition on the pressure drop buildup can be used in optimizing the loading of reactors and in other oil refining processes.
- 1 October 2023
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 63 (10) , 1203-1209
Dynamics of Silicon Sorption on the NiMo/Al2O3 Guard Bed Catalyst During Hydrotreating of Diesel
The dynamics of the silicon sorption on the NiMo/Al2O3 guard-bed catalyst containing ~2.0 wt % Ni and ~6.0 wt % Mo during hydrotreating of diesel was studied. The catalyst bed was divided into five equal sections separated by perforated metal partitions permeable to the feed. Four series of experiments were performed; their time was varied in the range 48–200 h, and the temperature was 340°C. A diesel fraction containing ~1.0 wt % sulfur, 130 ppm nitrogen, and 200 ppm silicon introduced in the form of decamethylcyclopentasiloxane was used as the feed. The specific surface area of all the spent samples was 170–190 m2/g, the pore volume was 0.35– 0.43 cm3/g, and the average pore diameter was 8–9 nm. The sorption on a catalyst grain 2.5 mm in diameter is diffusion-controlled. The effective mass transfer coefficient and the catalyst capacity under the experimental conditions (5 wt %) were estimated using the equation describing the sorption process.
- 1 October 2023
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 63 (10) , 1203-1209
Dynamics of Silicon Sorption on the NiMo/Al2O3 Guard Bed Catalyst During Hydrotreating of Diesel
The dynamics of the silicon sorption on the NiMo/Al2O3 guard-bed catalyst containing ~2.0 wt % Ni and ~6.0 wt % Mo during hydrotreating of diesel was studied. The catalyst bed was divided into five equal sections separated by perforated metal partitions permeable to the feed. Four series of experiments were performed; their time was varied in the range 48–200 h, and the temperature was 340°C. A diesel fraction containing ~1.0 wt % sulfur, 130 ppm nitrogen, and 200 ppm silicon introduced in the form of decamethylcyclopentasiloxane was used as the feed. The specific surface area of all the spent samples was 170–190 m2/g, the pore volume was 0.35– 0.43 cm3/g, and the average pore diameter was 8–9 nm. The sorption on a catalyst grain 2.5 mm in diameter is diffusion-controlled. The effective mass transfer coefficient and the catalyst capacity under the experimental conditions (5 wt %) were estimated using the equation describing the sorption process.
- 1 October 2022
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 62 (10) , 1204-1210
Effects of Tar Hydrocracking on Subsequent Carbonization
The study investigated thermal carbonization of oil tar in comparison with tar carbonization over a Ni/Sibunit catalyst at 450–600°C. The addition of Ni/Sibunit to the tar slightly enhanced the yield of coke. However, various sulfur compounds released during tar carbonization interact with metallic nickel to form nickel sulfide, thus rapidly deactivating the catalyst in carbonization that occurs by the carbide-cycle mechanism. To suppress the deactivation of 8%Ni/Sibunit under the impact of sulfur compounds, we hydrocracked the tar sample prior to feeding it to the carbonization. The tar hydrocracking was carried out in a flow-type reactor with a fixed bed of sulfided Ni–Mo/Al2O3 catalyst in a hydrogen atmosphere (the other reaction conditions included 16.0 MPa, 420°C, LHSV 0.5 h–1, and a hydrogen/feed ratio of 2000 v/v). The hydrocracking appreciably reduced the content of sulfur and nitrogen in the liquid product. In the presence of 8%Ni/Sibunit, the carbonization of the liquid tar hydrocracking product enhanced the yield of coke compared to that in the thermal carbonization. The catalytic carbonization was found to change the carbon morphology. Specifically, in the 8%Ni/Sibunit addition case, carbon nanofibers 15–40 nm in diameter were detected. In addition to the carbon nanofibers, the formation of amorphous carbon sheets was observed.
- 1 October 2022
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 62 (10) , 1204-1210
Effects of Tar Hydrocracking on Subsequent Carbonization
The study investigated thermal carbonization of oil tar in comparison with tar carbonization over a Ni/Sibunit catalyst at 450–600°C. The addition of Ni/Sibunit to the tar slightly enhanced the yield of coke. However, various sulfur compounds released during tar carbonization interact with metallic nickel to form nickel sulfide, thus rapidly deactivating the catalyst in carbonization that occurs by the carbide-cycle mechanism. To suppress the deactivation of 8%Ni/Sibunit under the impact of sulfur compounds, we hydrocracked the tar sample prior to feeding it to the carbonization. The tar hydrocracking was carried out in a flow-type reactor with a fixed bed of sulfided Ni–Mo/Al2O3 catalyst in a hydrogen atmosphere (the other reaction conditions included 16.0 MPa, 420°C, LHSV 0.5 h–1, and a hydrogen/feed ratio of 2000 v/v). The hydrocracking appreciably reduced the content of sulfur and nitrogen in the liquid product. In the presence of 8%Ni/Sibunit, the carbonization of the liquid tar hydrocracking product enhanced the yield of coke compared to that in the thermal carbonization. The catalytic carbonization was found to change the carbon morphology. Specifically, in the 8%Ni/Sibunit addition case, carbon nanofibers 15–40 nm in diameter were detected. In addition to the carbon nanofibers, the formation of amorphous carbon sheets was observed.