Donglin Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Donglin Xu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Dianguo Xu
Harbin Institute of Technology
2 shared publications - Ming Yang
Harbin Institute of Technology
2 shared publications - Yongchang Zhang
School of Electrical and Electronic Engineering, North China Electric Power University, Beijing, China
2 shared publications H.Y. Fang
School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, PR China
1 shared publication- Jian Jiao
Department of Electrical and Control Engineering, North China University of Technology, Beijing China
1 shared publication - Jiang Long
College of Communication Engineering, Jilin University, Changchun, China
1 shared publication
Latest Publications
- Open Access
- 21 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 91247-91259
A Transistor-Based Assist Gate Driver of SiC MOSFET for Crosstalk Suppression in a Phase-Leg Configuration
Crosstalk in a phase-leg configuration significantly limits the high switching performance of silicon carbide (SiC) MOSFETs and results in additional switching loss, self-excited oscillation and even parasitic conduction. To give full play to the fast switching potential of SiC MOSFET, this paper proposes a negative voltage transistor-based assist gate driver (NVTAGD) to suppress the voltage spike caused by the communication. First, a simple circuit composed of capacitor, resistor and diode is applied to establish a negative gate-source voltage level. Then, two auxiliary transistors cooperate with capacitors and diodes to actively suppress the positive and negative gate-source voltage spike. The auxiliary transistor can flexibly adjust its working mode according to the operation states of the circuit without additional control signals. Finally, parameter design criteria of main components are also given to meet different operating conditions. A double-pulse experimental setup based on SCT3022AL SiC MOSFET is established to illustrate the effectiveness of the proposed method. The proposed NVTAGD generates a negative voltage of -2.3 V for the synchronous freewheeling device. And the positive and negative crosstalk voltage spike decreases by 52.6% and 44.9% respectively. Both positive and negative crosstalk voltages are limited by the safe range. A series of experimental results illustrate that the proposed method not only suppresses the crosstalk voltage but also increases the reliability of the devices.
- 21 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 91247-91259
Open AccessA Transistor-Based Assist Gate Driver of SiC MOSFET for Crosstalk Suppression in a Phase-Leg Configuration
Crosstalk in a phase-leg configuration significantly limits the high switching performance of silicon carbide (SiC) MOSFETs and results in additional switching loss, self-excited oscillation and even parasitic conduction. To give full play to the fast switching potential of SiC MOSFET, this paper proposes a negative voltage transistor-based assist gate driver (NVTAGD) to suppress the voltage spike caused by the communication. First, a simple circuit composed of capacitor, resistor and diode is applied to establish a negative gate-source voltage level. Then, two auxiliary transistors cooperate with capacitors and diodes to actively suppress the positive and negative gate-source voltage spike. The auxiliary transistor can flexibly adjust its working mode according to the operation states of the circuit without additional control signals. Finally, parameter design criteria of main components are also given to meet different operating conditions. A double-pulse experimental setup based on SCT3022AL SiC MOSFET is established to illustrate the effectiveness of the proposed method. The proposed NVTAGD generates a negative voltage of -2.3 V for the synchronous freewheeling device. And the positive and negative crosstalk voltage spike decreases by 52.6% and 44.9% respectively. Both positive and negative crosstalk voltages are limited by the safe range. A series of experimental results illustrate that the proposed method not only suppresses the crosstalk voltage but also increases the reliability of the devices.
- 30 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 37 (4) , 2348-2358
EMI-Regulated SiC-Based Motor Drives With Markov Chain Pseudo-Random Frequency Space Vector Pulse Width Modulation Strategy
Compared with traditional silicon-based (Si) power devices, wide-bandgap (WBG) power devices have broader application prospects in AC motor drive due to their high-temperature reliability, low conduction, and switching losses. However, a fast switching process and high switching frequency will cause more serious electromagnetic interference (EMI) emission. To solve the problem, this paper proposed a pseudo-random frequency space vector pulse width modulation (PRF-SVPWM) strategy based on a carrier with a pseudo-random frequency. There are two sawtooth waves with the same frequency but opposite phases as alternatives. The proposed method randomly selects only one sawtooth wave during a complete control period. After random combination, the generated carrier is no longer a regular sawtooth wave. This new carrier contains 4 different modes including 2 sawtooth (positive and negative) and 2 triangular waves (positive and negative). A 2-state Markov chain is introduced to produce a PRF control signal which is regarded as the law of choice. In this way, the equivalent switching frequency keeps constant but the real-time switching frequency will randomly vary within the determined range. EMI emission level can be significantly reduced. The effectiveness of the proposed PRF-SVPWM is verified by several sets of experiment results.
- 30 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 37 (4) , 2348-2358
EMI-Regulated SiC-Based Motor Drives With Markov Chain Pseudo-Random Frequency Space Vector Pulse Width Modulation Strategy
Compared with traditional silicon-based (Si) power devices, wide-bandgap (WBG) power devices have broader application prospects in AC motor drive due to their high-temperature reliability, low conduction, and switching losses. However, a fast switching process and high switching frequency will cause more serious electromagnetic interference (EMI) emission. To solve the problem, this paper proposed a pseudo-random frequency space vector pulse width modulation (PRF-SVPWM) strategy based on a carrier with a pseudo-random frequency. There are two sawtooth waves with the same frequency but opposite phases as alternatives. The proposed method randomly selects only one sawtooth wave during a complete control period. After random combination, the generated carrier is no longer a regular sawtooth wave. This new carrier contains 4 different modes including 2 sawtooth (positive and negative) and 2 triangular waves (positive and negative). A 2-state Markov chain is introduced to produce a PRF control signal which is regarded as the law of choice. In this way, the equivalent switching frequency keeps constant but the real-time switching frequency will randomly vary within the determined range. EMI emission level can be significantly reduced. The effectiveness of the proposed PRF-SVPWM is verified by several sets of experiment results.
- 18 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (12) , 12024-12037
Direct Power Control of Doubly Fed Induction Generator Using Extended Power Theory Under Unbalanced Network
This paper proposes a novel DPC method for the DFIG power control system. The proposed DPC method is based on extended power theory rather than conventional instantaneous power theory. The proposed method calculates the rotor reference voltage based on the principle of deadbeat power control. Then, the rotor reference voltage is synthesized using space vector modulation (SVM). As a result, the switching frequency is constant, and satisfactory control performance is achieved under both balanced and unbalanced network conditions. This technique achieves the control targets of ensuring a constant stator-side active power, constant extended reactive power and sinusoidal stator currents without power compensation terms or other measures under unbalanced network conditions. Different from other DPC-SVM methods, the phase-locked loop (PLL) block is eliminated, and the whole structure of the control system is simple and easy to use. No parameters need to be tuned in the proposed method. The effectiveness of the proposed method is validated by the presented simulation and experimental results on a 1.5 kW laboratory DFIG control system.
- 18 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 34 (12) , 12024-12037
Direct Power Control of Doubly Fed Induction Generator Using Extended Power Theory Under Unbalanced Network
This paper proposes a novel DPC method for the DFIG power control system. The proposed DPC method is based on extended power theory rather than conventional instantaneous power theory. The proposed method calculates the rotor reference voltage based on the principle of deadbeat power control. Then, the rotor reference voltage is synthesized using space vector modulation (SVM). As a result, the switching frequency is constant, and satisfactory control performance is achieved under both balanced and unbalanced network conditions. This technique achieves the control targets of ensuring a constant stator-side active power, constant extended reactive power and sinusoidal stator currents without power compensation terms or other measures under unbalanced network conditions. Different from other DPC-SVM methods, the phase-locked loop (PLL) block is eliminated, and the whole structure of the control system is simple and easy to use. No parameters need to be tuned in the proposed method. The effectiveness of the proposed method is validated by the presented simulation and experimental results on a 1.5 kW laboratory DFIG control system.
- Open Access
- 9 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 65 (12) , 9356-9366
Generalized Multiple-Vector-Based Model Predictive Control for PMSM Drives
Model predictive control (MPC) is emerging as a powerful control method for the high performance control of permanent magnet synchronous motor (PMSM) drives due to its merits of simple principle, quick response and flexibility to handle multiple variables and constraints. However, conventional MPC applies only one voltage vector during one control period to minimize the cost function, which produces relatively high steady state ripples and high computational burden due to the enumeration based predictions. Introducing duty cycle control into MPC can improve its steady state performance, but the control complexity is further increased. This paper proposes a generalized multiple-vector based MPC for PMSM drives, which unifies the prior MPC methods in one frame with much lower complexity and computational burden by eliminating the enumeration-based predictions and complex calculations in conventional MPC methods. This is achieved by reconstructing the three phase duties obtained from the classical deadbeat control with modulator, which also reveals the inherent relationship between deadbeat control and the proposed MPC methods. The presented experimental results confirm the effectiveness of the proposed method.
- 9 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 65 (12) , 9356-9366
Open AccessGeneralized Multiple-Vector-Based Model Predictive Control for PMSM Drives
Model predictive control (MPC) is emerging as a powerful control method for the high performance control of permanent magnet synchronous motor (PMSM) drives due to its merits of simple principle, quick response and flexibility to handle multiple variables and constraints. However, conventional MPC applies only one voltage vector during one control period to minimize the cost function, which produces relatively high steady state ripples and high computational burden due to the enumeration based predictions. Introducing duty cycle control into MPC can improve its steady state performance, but the control complexity is further increased. This paper proposes a generalized multiple-vector based MPC for PMSM drives, which unifies the prior MPC methods in one frame with much lower complexity and computational burden by eliminating the enumeration-based predictions and complex calculations in conventional MPC methods. This is achieved by reconstructing the three phase duties obtained from the classical deadbeat control with modulator, which also reveals the inherent relationship between deadbeat control and the proposed MPC methods. The presented experimental results confirm the effectiveness of the proposed method.
- 12 August 2008
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 209 (7) , 3320-3324
Meshing and choice of evaluating parameters of results in simulation of electromagnetic force for forming of sheet metal
- 12 August 2008
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 209 (7) , 3320-3324
Meshing and choice of evaluating parameters of results in simulation of electromagnetic force for forming of sheet metal