Wojciech Gluchowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wojciech Gluchowski has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Barbara Kościelniak
Department of Materials Science, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Powstancow Warszawy Ave., 35-959 Rzeszow, Poland
2 shared publications - Kamil Dychtoń
Rzeszów University of Technology
2 shared publications - Kamil Ochal2 shared publications
- Marcin Drajewicz
Department of Materials Science, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstancow Warszawy 12, 35-959 Rzeszow, Poland
2 shared publications - Marek Goral
Rzeszów University of Technology
2 shared publications - Marek Łagoda
AGH University of Science and Technology
2 shared publications
Latest Publications
- Open Access
- 6 December 2023
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 23 (5) , 630-637
The Influence of Industrial-Scale Pack-Boroding Process Time on Thickness and Phase Composition of Selected Cold-Work Tool Steels
The boride coatings are characterized by attractive set of properties such as high hardness and wear resistance, corrosion resistance in higher temperatures and no wettability by liquid metals like aluminum and zinc. This type of coating might be used for manufacturing of different parts from tool steels. In present article the influence of pack boriding time (2, 4, 6h) on microstructure and phase composition of obtained coatings is scrutinized. The pack boriding process was conducted on two groups of cold work tool steels: low-Cr content: 145Cr6, 90MnCrV8, 60WCrV8 and high-Cr content: X165CrV12, X153CrMoV12. The commercial boriding pack Ekabor 2 was utilized and the process was carried out using industrial CVD device (Bernex BPX Pro 325S). The conducted research showed that the boride coatings formed on the substrate of high-chromium steels were characterized by a lower total thickness. On low-chromium steels, FeB phase was discontinuous as an irregular islands located in the near-surface area. On the other hand, for high-chromium steels, a continuous layer of needle-like borides was formed.
- 6 December 2023
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 23 (5) , 630-637
Open AccessThe Influence of Industrial-Scale Pack-Boroding Process Time on Thickness and Phase Composition of Selected Cold-Work Tool Steels
The boride coatings are characterized by attractive set of properties such as high hardness and wear resistance, corrosion resistance in higher temperatures and no wettability by liquid metals like aluminum and zinc. This type of coating might be used for manufacturing of different parts from tool steels. In present article the influence of pack boriding time (2, 4, 6h) on microstructure and phase composition of obtained coatings is scrutinized. The pack boriding process was conducted on two groups of cold work tool steels: low-Cr content: 145Cr6, 90MnCrV8, 60WCrV8 and high-Cr content: X165CrV12, X153CrMoV12. The commercial boriding pack Ekabor 2 was utilized and the process was carried out using industrial CVD device (Bernex BPX Pro 325S). The conducted research showed that the boride coatings formed on the substrate of high-chromium steels were characterized by a lower total thickness. On low-chromium steels, FeB phase was discontinuous as an irregular islands located in the near-surface area. On the other hand, for high-chromium steels, a continuous layer of needle-like borides was formed.
- 6 March 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 68 (1) , 295-306
Research on Changes in Microstructures and Mechanical Properties of Welding Caps as a Result of their Usage During Resistance Spot Welding Process
Mating electrodes made of copper alloys are commonly used for welding galvanized steel sheets used in the production of car bodies. These alloys are characterized by high mechanical properties, a high level of electrical and thermal conductivity as well as the stability of these properties under changing conditions of current, thermal and mechanical load. Much careful attention was paid to the essence of the ongoing structural changes as well as to the mechanical properties in the welding process (RSW – Resistant Spot Welding) of steel sheets, including high-strength ones. There is a lack of research on structural changes and the related mechanical properties occurring in welding electrodes made of copper alloys caused by the welding process. This study is devoted to these issues and contains a critical review of the research results enabling a better understanding of the relationships between the structure and properties of welding electrodes caused by the cyclic welding process. In order to illustrate the phenomena occurring during the welding process, both in the material to be welded and in the tip electrodes, hardness and structural tests were carried out on electrode samples before and after their exploitation. The data collected in the article supplements a certain lack of information in the literature regarding the microstructural aspects of the welding process of galvanized steel sheets for the production of car bodies. The conducted research may be the starting point for the search for more effective materials for the tip electrodes.
- 6 March 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 68 (1) , 295-306
Research on Changes in Microstructures and Mechanical Properties of Welding Caps as a Result of their Usage During Resistance Spot Welding Process
Mating electrodes made of copper alloys are commonly used for welding galvanized steel sheets used in the production of car bodies. These alloys are characterized by high mechanical properties, a high level of electrical and thermal conductivity as well as the stability of these properties under changing conditions of current, thermal and mechanical load. Much careful attention was paid to the essence of the ongoing structural changes as well as to the mechanical properties in the welding process (RSW – Resistant Spot Welding) of steel sheets, including high-strength ones. There is a lack of research on structural changes and the related mechanical properties occurring in welding electrodes made of copper alloys caused by the welding process. This study is devoted to these issues and contains a critical review of the research results enabling a better understanding of the relationships between the structure and properties of welding electrodes caused by the cyclic welding process. In order to illustrate the phenomena occurring during the welding process, both in the material to be welded and in the tip electrodes, hardness and structural tests were carried out on electrode samples before and after their exploitation. The data collected in the article supplements a certain lack of information in the literature regarding the microstructural aspects of the welding process of galvanized steel sheets for the production of car bodies. The conducted research may be the starting point for the search for more effective materials for the tip electrodes.
- Open Access
- 11 December 2022
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 22 (5) , 530-541
The Diffusion Coatings for Industrial Tool Application
The diffusion boriding process allows to increase the abrasion and corrosion resistance of the majority of steel grades. The aim of this study was to determine the influence of the chemical composition of the substrate of various steel grades ...
- 11 December 2022
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 22 (5) , 530-541
Open AccessThe Diffusion Coatings for Industrial Tool Application
The diffusion boriding process allows to increase the abrasion and corrosion resistance of the majority of steel grades. The aim of this study was to determine the influence of the chemical composition of the substrate of various steel grades ...
- Open Access
- 1 June 2014
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 59 (2) , 649-658
Mechanism and Kinetics of Precipitation Process in Selected Copper Alloys
Wymagane cechy użytkowe których oczekuje się od stopów miedzi wywierają zasadniczy wpływ na ich technologiczny proces wytwarzania. Wynika stąd konieczność rozeznania zakresu zmian własności użytkowych wynikających z zastosowanego wariantu obróbki cieplnej i plastycznej. Stopy miedzi CuTi4, CuFe2, CuCr0.7 i CuNi2Sil poddane badaniu w niniejszej pracy dobrano w ten sposób aby różniły się fazami umacniającymi. Próbki poddano przesycaniu, odkształceniu na zimno (walcowanie) oraz starzeniu. Przesycone stopy CuTi4, CuFe2. CuCr0.7 oraz CuNi2Sil różnią się mechanizmem i kinetyką wydzielania podczas procesu starzenia. Procesy te są złożone i uzależnione od niejednorodności rozmieszczenia składników stopowych w osnowie miedzianej, historii wytwarzania i przetwarzania stopów, parametrów przesycania i starzenia jak tez wielkości odkształcenia na zimno
- 1 June 2014
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 59 (2) , 649-658
Open AccessMechanism and Kinetics of Precipitation Process in Selected Copper Alloys
Wymagane cechy użytkowe których oczekuje się od stopów miedzi wywierają zasadniczy wpływ na ich technologiczny proces wytwarzania. Wynika stąd konieczność rozeznania zakresu zmian własności użytkowych wynikających z zastosowanego wariantu obróbki cieplnej i plastycznej. Stopy miedzi CuTi4, CuFe2, CuCr0.7 i CuNi2Sil poddane badaniu w niniejszej pracy dobrano w ten sposób aby różniły się fazami umacniającymi. Próbki poddano przesycaniu, odkształceniu na zimno (walcowanie) oraz starzeniu. Przesycone stopy CuTi4, CuFe2. CuCr0.7 oraz CuNi2Sil różnią się mechanizmem i kinetyką wydzielania podczas procesu starzenia. Procesy te są złożone i uzależnione od niejednorodności rozmieszczenia składników stopowych w osnowie miedzianej, historii wytwarzania i przetwarzania stopów, parametrów przesycania i starzenia jak tez wielkości odkształcenia na zimno