Sahul Hameed Mohamed Abbas
Sahul Hameed Mohamed Abbas has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Chinathambi Muthukaruppan Meenakshi
Bharath Institute of Higher Education and Research, India
1 shared publication D. Ramesh Kumar
Department of Mechanical Engineering, Adithya Institute of Technology, Coimbatore, India
1 shared publicationG. Arunkumar
Department of Mechanical Engineering, Sathyabama Institute of Science and Technology, Chennai, India
1 shared publication- Ganesamoorthy Raju
Department of Mechanical Engineering, Chennai Institute of Technology, Chennai, India
1 shared publication - Gopi Suresh
Department of Mechanical Engineering, Rajalakshmi Institute of Technology, Kuthambakkam, Chennai, India
1 shared publication - Jeevanandam Rajaparthiban
Chennai Institute of Technology, India
1 shared publication
Latest Publications
- 19 October 2026
- Published by Springer Nature in Silicon
- p. 1-14
Development and Characterization of 3D Printed PLA Composites Using Palm Oil Fuel Ash and Garlic Skin Fibers
- 19 October 2026
- Published by Springer Nature in Silicon
- p. 1-14
Development and Characterization of 3D Printed PLA Composites Using Palm Oil Fuel Ash and Garlic Skin Fibers
- 21 January 2026
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 14 (1)
Surface Topography and Frictional Wear Behavior of Plasma-Sprayed Ceria and Alumina Fused Yttria-Stabilized Zirconia (CAFYZ) Coated Al–Si Alloy
This study investigates the tribological performance of the plasma-sprayed Ceria and Alumina Fused Yttria-stabilized Zirconia (CAFYZ) Thermal Barrier Coatings (TBCs) over the Al20Cr20Ni60 bond-coated Al-Si alloy for the piston application. The evaluation of surface morphology, thermogravimetric behavior, and tribological behavior for CAFYZ TBCs reveals that the addition of Ceria (CeO2) from 2 to 6 wt.% has significantly enhanced the thermal and wear resistance of the CAFYZ TBCs. The 6CAFYZ TBC reduced the crystallite size from 54.44 nm (AFYZ TBC) to 32.34 nm due to the formation of wet edges and improved microstructural integrity. It also enhanced the microhardness by 10.2 times (1298 HV) and the thermal stability by 2.2 times (1370.3 K) compared to the Al-Si alloy. The 6CAFYZ TBC improved the frictional wear resistance of the Al-Si alloy by 6.3 times, achieving a wear rate of 6.59 × 10-5 g/m and a Coefficient of Friction (CoF) of 0.416 at an applied load of 10 N and a sliding velocity of 3 m/s. The worn surface analysis of CAFYZ TBCs reveals a transition in dominant wear mechanisms with increasing applied load and sliding velocity. The wear maps showed a clear transition in wear mechanisms from abrasive to adhesive with increasing CeO2 content. Compared with literature, these coatings achieved lower wear rates and superior stability. The novelty of this work lies in demonstrating the dual improvement in frictional wear resistance and high-temperature durability in CeO2 modified CAFYZ TBCs.
- 21 January 2026
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 14 (1)
Surface Topography and Frictional Wear Behavior of Plasma-Sprayed Ceria and Alumina Fused Yttria-Stabilized Zirconia (CAFYZ) Coated Al–Si Alloy
This study investigates the tribological performance of the plasma-sprayed Ceria and Alumina Fused Yttria-stabilized Zirconia (CAFYZ) Thermal Barrier Coatings (TBCs) over the Al20Cr20Ni60 bond-coated Al-Si alloy for the piston application. The evaluation of surface morphology, thermogravimetric behavior, and tribological behavior for CAFYZ TBCs reveals that the addition of Ceria (CeO2) from 2 to 6 wt.% has significantly enhanced the thermal and wear resistance of the CAFYZ TBCs. The 6CAFYZ TBC reduced the crystallite size from 54.44 nm (AFYZ TBC) to 32.34 nm due to the formation of wet edges and improved microstructural integrity. It also enhanced the microhardness by 10.2 times (1298 HV) and the thermal stability by 2.2 times (1370.3 K) compared to the Al-Si alloy. The 6CAFYZ TBC improved the frictional wear resistance of the Al-Si alloy by 6.3 times, achieving a wear rate of 6.59 × 10-5 g/m and a Coefficient of Friction (CoF) of 0.416 at an applied load of 10 N and a sliding velocity of 3 m/s. The worn surface analysis of CAFYZ TBCs reveals a transition in dominant wear mechanisms with increasing applied load and sliding velocity. The wear maps showed a clear transition in wear mechanisms from abrasive to adhesive with increasing CeO2 content. Compared with literature, these coatings achieved lower wear rates and superior stability. The novelty of this work lies in demonstrating the dual improvement in frictional wear resistance and high-temperature durability in CeO2 modified CAFYZ TBCs.
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 27 (2)
Effect of polyurethane ratio on mechanical behavior of banana fiber/polyurethane-vinylester matrix composites
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 27 (2)
Open AccessEffect of polyurethane ratio on mechanical behavior of banana fiber/polyurethane-vinylester matrix composites