Prabhuraj Balakrishnan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Prabhuraj Balakrishnan has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Huaneng Su
Institute for Energy Research, Jiangsu University, Zhenjiang 212013, China
1 shared publication - Huiyuan Liu
Institute for Energy Research, Jiangsu University, Zhenjiang 212013, China
1 shared publication - Lei Xing
School of Chemistry and Chemical Engineering University of Surrey Guildford UK
1 shared publication - Li Guan
Institute for Energy Research, Jiangsu University, Zhenjiang 212013, China
1 shared publication - Marcelo Lozada-Hidalgo
Department of Physics and Astronomy, The University of Manchester, Manchester, UK
1 shared publication Pulickel M. Ajayan
Department of Materials Science and NanoEngineering Rice University 6100 Main, MS‐321 Houston TX 77005‐1892 USA
1 shared publication
Latest Publications
- Open Access
A Tortuosity Engineered Dual-Microporous Layer Electrode Including Graphene Aerogel Enabling Largely Improved Direct Methanol Fuel Cell Performance with High-Concentration Fuel
Methanol crossover is an important factor affecting the performance of direct methanol fuel cells (DMFCs). In this work, a novel membrane electrode assembly (MEA) is designed and prepared by adding a layer of graphene aerogel (GA) between the carbon powder microporous layer and the catalytic layer, which optimizes the methanol transport and improves the output performance of DMFC at high methanol concentrations. Compared to conventional carbon powder, the addition of GA increases the tortuosity of the anode in the through-plane direction; hence, methanol is diluted to a suitable concentration when it reaches the catalyst. The maximum power density of the novel MEA can reach 27.4 mW·cm−2 at a condition of 8 M methanol, which is 234% higher than that of the conventional electrode. The test results of electrochemical impedance spectroscopy (EIS) indicate that the addition of GA does not increase the internal resistance of the novel MEA and that the mass transfer resistance at high concentrations is significantly lower. The experimental results indicate that the output performance at high concentration can be significantly improved by adding a GA layer, and its practicability in portable devices can be improved. It also improves the stability of DMFC under long-term testing.
Open AccessA Tortuosity Engineered Dual-Microporous Layer Electrode Including Graphene Aerogel Enabling Largely Improved Direct Methanol Fuel Cell Performance with High-Concentration Fuel
Methanol crossover is an important factor affecting the performance of direct methanol fuel cells (DMFCs). In this work, a novel membrane electrode assembly (MEA) is designed and prepared by adding a layer of graphene aerogel (GA) between the carbon powder microporous layer and the catalytic layer, which optimizes the methanol transport and improves the output performance of DMFC at high methanol concentrations. Compared to conventional carbon powder, the addition of GA increases the tortuosity of the anode in the through-plane direction; hence, methanol is diluted to a suitable concentration when it reaches the catalyst. The maximum power density of the novel MEA can reach 27.4 mW·cm−2 at a condition of 8 M methanol, which is 234% higher than that of the conventional electrode. The test results of electrochemical impedance spectroscopy (EIS) indicate that the addition of GA does not increase the internal resistance of the novel MEA and that the mass transfer resistance at high concentrations is significantly lower. The experimental results indicate that the output performance at high concentration can be significantly improved by adding a GA layer, and its practicability in portable devices can be improved. It also improves the stability of DMFC under long-term testing.
- 3 November 2016
- Published by Wiley in Advanced Energy Materials
- Vol. 7 (5) , 1601216
2D Crystals Significantly Enhance the Performance of a Working Fuel Cell
2D atomic crystals such as single layer graphene (SLG) and hexagonal boron nitride (hBN) have been shown to be “unexpectedly permeable” to hydrogen ions under ambient conditions with the proton conductivity rising exponentially with temperature. Here, the first successful addition of SLG made by a chemical vapor deposition (CVD) method is shown to an operational direct methanol fuel cell significantly enhancing the performance of the cell once the temperature is raised above 60 °C, the temperature at which the proton conductivity of SLG is higher than the Nafion membrane on which it is mounted. Above this temperature, the resistance to proton transport of the system is not affected by the graphene but the barrier properties of graphene inhibit methanol crossover. The performance of the fuel cell is shown to increase linearly with coverage of SLG above this temperature. Results show that the maximum power density is increased at 70 °C by 45% in comparison to the standard membrane electrode assembly without graphene. In addition, a membrane with CVD hBN shows enhanced performance across the entire temperature range due to better proton conductivity at lower temperatures.
- 3 November 2016
- Published by Wiley in Advanced Energy Materials
- Vol. 7 (5) , 1601216
2D Crystals Significantly Enhance the Performance of a Working Fuel Cell
2D atomic crystals such as single layer graphene (SLG) and hexagonal boron nitride (hBN) have been shown to be “unexpectedly permeable” to hydrogen ions under ambient conditions with the proton conductivity rising exponentially with temperature. Here, the first successful addition of SLG made by a chemical vapor deposition (CVD) method is shown to an operational direct methanol fuel cell significantly enhancing the performance of the cell once the temperature is raised above 60 °C, the temperature at which the proton conductivity of SLG is higher than the Nafion membrane on which it is mounted. Above this temperature, the resistance to proton transport of the system is not affected by the graphene but the barrier properties of graphene inhibit methanol crossover. The performance of the fuel cell is shown to increase linearly with coverage of SLG above this temperature. Results show that the maximum power density is increased at 70 °C by 45% in comparison to the standard membrane electrode assembly without graphene. In addition, a membrane with CVD hBN shows enhanced performance across the entire temperature range due to better proton conductivity at lower temperatures.