Laurent Lestarquit
Research Subjects
Laurent Lestarquit has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Corentin Lubeigt
Telecommunication for Space and Aeronautics (TéSA) Laboratory, 31500 Toulouse, France
3 shared publications - Eric Chaumette
ISAE-SUPAERO, Toulouse, France
3 shared publications - Jordi Vilà-Valls
ISAE-SUPAERO, University of Toulouse, Toulouse, France
3 shared publications - Lorenzo Ortega
IPSA, Toulouse, France
3 shared publications - José Cali
Laboratoire Géomatique et Foncier (GeF) UR 4630, Conservatoire National des Arts et Métiers (Cnam), HESAM Université, École Supérieure d’Ingénieurs Géomètres Topographes (ESGT), 1 Boulevard Pythagore, 72000 Le Mans, France
1 shared publication - Jérôme Verdun
Conservatoire national des arts et métiers GeF EA4630 F-72000 Le Mans France
1 shared publication
Latest Publications
- Open Access
- 25 August 2023
- Published by MDPI AG in Remote Sensing
- Vol. 15 (17) , 4192
Lake Altimetry Using Long Coherent Integration Carrier Phase Measurements from Airborne GNSS Reflectometry
Today, land and ocean observations are crucial for monitoring climate change. The method of GNSS reflectometry is an opportunistic way to provide low-cost observations of many geophysical parameters. However, although this method has been the subject of numerous research studies, work is still in progress to improve its possibilities and fields of application. This paper focuses on GNSS reflectometry using carrier phase measurements for water altimetry measurements. The difficulties in implementing such a method lie in the need to collect a coherent signal and to solve the integer ambiguity value. In this context, the implementation of innovative signal processing is described, including the correlation of the reflected signals in dedicated software and the prolongation of the coherent integration time to enhance signal coherency. These processes were applied to data collected over Carcans-Hourtin Lake in France to compute the height of the reflection surface which was then compared to in situ GNSS buoy height measurements. The results show that at 300 ft (91.44 m), the differences between the lake heights measured with the buoy and with the reflectometry data can reach less than 1 cm for the L1, E1 and E5 GNSS signals. In addition, the slope of the geoid estimated with the reflectometry data is very consistent with that of the RAF20 geoid model, with a difference of up to less than 2 mm/km.
- 25 August 2023
- Published by MDPI AG in Remote Sensing
- Vol. 15 (17) , 4192
Open AccessLake Altimetry Using Long Coherent Integration Carrier Phase Measurements from Airborne GNSS Reflectometry
Today, land and ocean observations are crucial for monitoring climate change. The method of GNSS reflectometry is an opportunistic way to provide low-cost observations of many geophysical parameters. However, although this method has been the subject of numerous research studies, work is still in progress to improve its possibilities and fields of application. This paper focuses on GNSS reflectometry using carrier phase measurements for water altimetry measurements. The difficulties in implementing such a method lie in the need to collect a coherent signal and to solve the integer ambiguity value. In this context, the implementation of innovative signal processing is described, including the correlation of the reflected signals in dedicated software and the prolongation of the coherent integration time to enhance signal coherency. These processes were applied to data collected over Carcans-Hourtin Lake in France to compute the height of the reflection surface which was then compared to in situ GNSS buoy height measurements. The results show that at 300 ft (91.44 m), the differences between the lake heights measured with the buoy and with the reflectometry data can reach less than 1 cm for the L1, E1 and E5 GNSS signals. In addition, the slope of the geoid estimated with the reflectometry data is very consistent with that of the RAF20 geoid model, with a difference of up to less than 2 mm/km.
- 3 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. 58 (6) , 5412-5424
Clean-to-Composite Bound Ratio: A Multipath Criterion for GNSS Signal Design and Analysis
Multipath is one of the most challenging propagation conditions affecting Global Navigation Satellite Systems (GNSS), which must be mitigated in order to obtain reliable navigation information. In any case, the random multipath nature makes it difficult to anticipate and overcome. Therefore, for legacy GNSS signal performance assessment, modern GNSS signal design and future GNSS-based applications, robustness to multipath is a fundamental criterion. Different multipath metrics exist in the literature, such as the multipath error envelope, usually leading to analyses only valid for a dedicated receiver/signal combination and only providing information on the bias. This paper presents a general criterion to characterize the multipath robustness of a generic band-limited signal (e.g., GNSS or radar), considering the joint delay-Doppler and phase estimation. This criterion is based on the Cramr-Rao bound, which makes it universal, regardless the receiver architecture and the signal under analysis, and provides information on the actual achievable performance in terms of estimated time-delay (i.e., pseudo-range) and Doppler frequency variances.
- 3 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. 58 (6) , 5412-5424
Clean-to-Composite Bound Ratio: A Multipath Criterion for GNSS Signal Design and Analysis
Multipath is one of the most challenging propagation conditions affecting Global Navigation Satellite Systems (GNSS), which must be mitigated in order to obtain reliable navigation information. In any case, the random multipath nature makes it difficult to anticipate and overcome. Therefore, for legacy GNSS signal performance assessment, modern GNSS signal design and future GNSS-based applications, robustness to multipath is a fundamental criterion. Different multipath metrics exist in the literature, such as the multipath error envelope, usually leading to analyses only valid for a dedicated receiver/signal combination and only providing information on the bias. This paper presents a general criterion to characterize the multipath robustness of a generic band-limited signal (e.g., GNSS or radar), considering the joint delay-Doppler and phase estimation. This criterion is based on the Cramr-Rao bound, which makes it universal, regardless the receiver architecture and the signal under analysis, and provides information on the actual achievable performance in terms of estimated time-delay (i.e., pseudo-range) and Doppler frequency variances.
- Open Access
- 12 March 2021
- Published by MDPI AG in Remote Sensing
- Vol. 13 (6) , 1085
On the Impact and Mitigation of Signal Crosstalk in Ground-Based and Low Altitude Airborne GNSS-R
Global Navigation Satellite System Reflectometry (GNSS-R) is a powerful way to retrieve information from a reflecting surface by exploiting GNSS as signals of opportunity. In dual antenna conventional GNSS-R architectures, the reflected signal is correlated with a clean replica to obtain the specular reflection point delay and Doppler estimates, which are further processed to obtain the GNSS-R product of interest. An important problem that may appear for low elevation satellites is signal crosstalk, that is the direct line-of-sight signal leaks into the antenna dedicated to the reflected signal. Such crosstalk may degrade the overall system performance if both signals are very close in time, similar to multipath in standard GNSS receivers, the reason why mitigation strategies must be accounted for. In this article: (i) we first provide a geometrical analysis to justify that the estimation performance is only affected for low height receivers; (ii) then, we analyze the impact of crosstalk if not taken into account, by comparing the single source conditional maximum likelihood estimator (CMLE) performance in a dual source context with the corresponding Cramér–Rao bound (CRB); (iii) we discuss dual source estimators as a possible mitigation strategy; and (iv) we investigate the performance of the so-called variance estimator, which is designed to eliminate the coherent signal part, compared to both the CRB and non-coherent dual source estimators. Simulation results are provided for representative GNSS signals to support the discussion. From this analysis, it is found that: (i) for low enough reflected-to-direct signal amplitude ratios (RDR), the crosstalk has no impact on standard single source CMLEs; (ii) for high enough signal-to-noise ratios (SNR), the dual source estimators are efficient irrespective of the RDR, then being a promising solution for any reflected signal scenario; (iii) non-coherent dual source estimators are also efficient at high SNR; and (iv) the variance estimator is efficient as long as the non-coherent part of the signal is dominant.
- 12 March 2021
- Published by MDPI AG in Remote Sensing
- Vol. 13 (6) , 1085
Open AccessOn the Impact and Mitigation of Signal Crosstalk in Ground-Based and Low Altitude Airborne GNSS-R
Global Navigation Satellite System Reflectometry (GNSS-R) is a powerful way to retrieve information from a reflecting surface by exploiting GNSS as signals of opportunity. In dual antenna conventional GNSS-R architectures, the reflected signal is correlated with a clean replica to obtain the specular reflection point delay and Doppler estimates, which are further processed to obtain the GNSS-R product of interest. An important problem that may appear for low elevation satellites is signal crosstalk, that is the direct line-of-sight signal leaks into the antenna dedicated to the reflected signal. Such crosstalk may degrade the overall system performance if both signals are very close in time, similar to multipath in standard GNSS receivers, the reason why mitigation strategies must be accounted for. In this article: (i) we first provide a geometrical analysis to justify that the estimation performance is only affected for low height receivers; (ii) then, we analyze the impact of crosstalk if not taken into account, by comparing the single source conditional maximum likelihood estimator (CMLE) performance in a dual source context with the corresponding Cramér–Rao bound (CRB); (iii) we discuss dual source estimators as a possible mitigation strategy; and (iv) we investigate the performance of the so-called variance estimator, which is designed to eliminate the coherent signal part, compared to both the CRB and non-coherent dual source estimators. Simulation results are provided for representative GNSS signals to support the discussion. From this analysis, it is found that: (i) for low enough reflected-to-direct signal amplitude ratios (RDR), the crosstalk has no impact on standard single source CMLEs; (ii) for high enough signal-to-noise ratios (SNR), the dual source estimators are efficient irrespective of the RDR, then being a promising solution for any reflected signal scenario; (iii) non-coherent dual source estimators are also efficient at high SNR; and (iv) the variance estimator is efficient as long as the non-coherent part of the signal is dominant.
- Open Access
- 27 November 2020
- Published by MDPI AG in Remote Sensing
- Vol. 12 (23) , 3894
Joint Delay-Doppler Estimation Performance in a Dual Source Context
Evaluating the time-delay, Doppler effect and carrier phase of a received signal is a challenging estimation problem that was addressed in a large variety of remote sensing applications. This problem becomes more difficult and less understood when the signal is reflected off one or multiple surfaces and interferes with itself at the receiver stage. This phenomenon might deteriorate the overall system performance, as for the multipath effect in Global Navigation Satellite Systems (GNSS), and mitigation strategies must be accounted for. In other applications such as GNSS reflectometry (GNSS-R) it may be interesting to estimate the parameters of the reflected signal to deduce the geometry and the surface characteristics. In either case, a better understanding of this estimation problem is directly brought by the corresponding lower performance bounds. In the high signal-to-noise ratio regime of the Gaussian conditional signal model, the Cramér-Rao bound (CRB) provides an accurate lower bound in the mean square error sense. In this article, we derive a new compact CRB expression for the joint time-delay and Doppler estimation in a dual source context, considering a band-limited signal and its specular reflection. These compact CRBs are expressed in terms of the baseband signal samples, making them especially easy to use whatever the baseband signal considered, therefore being valid for a variety of remote sensors. This extends existing results in the single source context and opens the door to a plethora of usages to be discussed in the article. The proposed CRB expressions are validated in two representative navigation and radar examples.
- 27 November 2020
- Published by MDPI AG in Remote Sensing
- Vol. 12 (23) , 3894
Open AccessJoint Delay-Doppler Estimation Performance in a Dual Source Context
Evaluating the time-delay, Doppler effect and carrier phase of a received signal is a challenging estimation problem that was addressed in a large variety of remote sensing applications. This problem becomes more difficult and less understood when the signal is reflected off one or multiple surfaces and interferes with itself at the receiver stage. This phenomenon might deteriorate the overall system performance, as for the multipath effect in Global Navigation Satellite Systems (GNSS), and mitigation strategies must be accounted for. In other applications such as GNSS reflectometry (GNSS-R) it may be interesting to estimate the parameters of the reflected signal to deduce the geometry and the surface characteristics. In either case, a better understanding of this estimation problem is directly brought by the corresponding lower performance bounds. In the high signal-to-noise ratio regime of the Gaussian conditional signal model, the Cramér-Rao bound (CRB) provides an accurate lower bound in the mean square error sense. In this article, we derive a new compact CRB expression for the joint time-delay and Doppler estimation in a dual source context, considering a band-limited signal and its specular reflection. These compact CRBs are expressed in terms of the baseband signal samples, making them especially easy to use whatever the baseband signal considered, therefore being valid for a variety of remote sensors. This extends existing results in the single source context and opens the door to a plethora of usages to be discussed in the article. The proposed CRB expressions are validated in two representative navigation and radar examples.