Daiyue Wei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Daiyue Wei has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Albert Kim
Department of Medical Engineering, University of South Florida, Tampa, FL, USA
1 shared publication - Ali Ashraf
Department of Mechanical Engineering, The University of South Florida, Tampa, FL 33620, USA
1 shared publication Asif Hasan Ridoy
University of South Florida
1 shared publicationChanyapat Sriviroch
University of South Florida
1 shared publication- Hongqiang Wang
Southern University of Science and Technology
1 shared publication - Huacen Wang
SUSTech Institute for Robotics Research, Southern University of Science and Technology, Shenzhen, China
1 shared publication
Latest Publications
- 4 November 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (45) , 33655-33664
Efficient Screening of Long-Wavelength Interfacial Moiré Superlattices in Self-Folded Two-Dimensional Materials
Moiré superlattices at two-dimensional (2D) material interfaces enable emergent electronic, electrical, and optical phenomena, yet their preparation remains constrained by complex fabrication and limited throughput. Here, we transform the preparation of hexagonal boron nitride (hBN) moiré homojunctions from a fabrication challenge into a classification problem by directly identifying parallel-stacked moiré samples with long wavelengths from spontaneously self-folded flakes following tape exfoliation. By exploiting the intrinsic cleavage behavior and wrinkle formation of layered materials, this strategy enables efficient screening and scalable batch production of these specific moiré structures. Correlative electrostatic force microscopy (EFM) and transmission electron microscopy (TEM) reveal that only parallel-stacked flakes exhibit electrostatic contrast associated with out-of-plane polarization. EFM, Kelvin probe force microscopy (KPFM), and Raman spectroscopy further identify AB/BA stacking domains and their transition regions. To accelerate and automate moiré identification, an XGBoost-based screening workflow achieves a mean test ROC-AUC of 0.78 ± 0.14. Compared with the conventional tear-and-stack approach, this method reduces moiré preparation time by at least 40% while eliminating manual stacking, providing a simple, scalable, and broadly applicable strategy for preparing high-quality interfacial moiré superlattices in 2D materials for next-generation moiré-based electronic and optoelectronic devices.
- 4 November 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (45) , 33655-33664
Efficient Screening of Long-Wavelength Interfacial Moiré Superlattices in Self-Folded Two-Dimensional Materials
Moiré superlattices at two-dimensional (2D) material interfaces enable emergent electronic, electrical, and optical phenomena, yet their preparation remains constrained by complex fabrication and limited throughput. Here, we transform the preparation of hexagonal boron nitride (hBN) moiré homojunctions from a fabrication challenge into a classification problem by directly identifying parallel-stacked moiré samples with long wavelengths from spontaneously self-folded flakes following tape exfoliation. By exploiting the intrinsic cleavage behavior and wrinkle formation of layered materials, this strategy enables efficient screening and scalable batch production of these specific moiré structures. Correlative electrostatic force microscopy (EFM) and transmission electron microscopy (TEM) reveal that only parallel-stacked flakes exhibit electrostatic contrast associated with out-of-plane polarization. EFM, Kelvin probe force microscopy (KPFM), and Raman spectroscopy further identify AB/BA stacking domains and their transition regions. To accelerate and automate moiré identification, an XGBoost-based screening workflow achieves a mean test ROC-AUC of 0.78 ± 0.14. Compared with the conventional tear-and-stack approach, this method reduces moiré preparation time by at least 40% while eliminating manual stacking, providing a simple, scalable, and broadly applicable strategy for preparing high-quality interfacial moiré superlattices in 2D materials for next-generation moiré-based electronic and optoelectronic devices.
- 20 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Robotics
- Vol. 38 (6) , 3450-3462
So-EAGlove: VR Haptic Glove Rendering Softness Sensation With Force-Tunable Electrostatic Adhesive Brakes
Haptic gloves allow the players to feel the virtual world more realistically by providing force feedback. At present, haptic gloves are mainly driven by conventional motors, and for them, being lightweight, low cost, low in power consumption, and intrinsically safe to operators are challenging. Here, we designed a haptic glove (So-EAGlove) integrating a flexible electrostatic adhesive brake to resist human fingers with a tunable braking force and render a softness sensation. This glove weighs only 51 g, but is capable of simulating objects in a large range of Young's modulus from 540 Pa to 5.4 MPa. The electrostatic adhesive brake costs only approximately 2.43 mW during operation, i.e., more than three days powered by a small button battery. We built a feedforward control model and evaluated its performance. Experimental results show that this glove can generate an accurate force to follow the force-displacement profile of the corresponding real objects. The error is less than 7%, barely noticeable by the subjects. The subjective tests also demonstrate that little statistical difference exists between the real objects and the virtual objects for the subjects.
- 20 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Robotics
- Vol. 38 (6) , 3450-3462
So-EAGlove: VR Haptic Glove Rendering Softness Sensation With Force-Tunable Electrostatic Adhesive Brakes
Haptic gloves allow the players to feel the virtual world more realistically by providing force feedback. At present, haptic gloves are mainly driven by conventional motors, and for them, being lightweight, low cost, low in power consumption, and intrinsically safe to operators are challenging. Here, we designed a haptic glove (So-EAGlove) integrating a flexible electrostatic adhesive brake to resist human fingers with a tunable braking force and render a softness sensation. This glove weighs only 51 g, but is capable of simulating objects in a large range of Young's modulus from 540 Pa to 5.4 MPa. The electrostatic adhesive brake costs only approximately 2.43 mW during operation, i.e., more than three days powered by a small button battery. We built a feedforward control model and evaluated its performance. Experimental results show that this glove can generate an accurate force to follow the force-displacement profile of the corresponding real objects. The error is less than 7%, barely noticeable by the subjects. The subjective tests also demonstrate that little statistical difference exists between the real objects and the virtual objects for the subjects.