Lidong Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Lidong Zhao has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Lifang Wu
Beijing University of Technology, China
4 shared publications - Zening Men
Beijing University of Technology, China
2 shared publications - Zhi Zhao
State Key Laboratory of Materials Low‐Carbon Recycling Key Laboratory of Advanced Functional Materials Education Ministry of China College of Material Science and Engineering Beijing University of Technology Beijing 100124 China
2 shared publications - Feng Yang
Beijing University of Technology, China
1 shared publication - Ge Shi
Beijing Institute of Technology, Beijing, Beijing, CHINA
1 shared publication Lifang Wu
1 shared publication
Latest Publications
- Open Access
- 2 December 2024
- Published by Association for Computing Machinery (ACM)
- p. 1-2
Hybrid Physical Model and Status Data-Driven Dynamic Control for Digital Light Processing 3D Printing
- 2 December 2024
- Published by Association for Computing Machinery (ACM)
- p. 1-2
Open AccessHybrid Physical Model and Status Data-Driven Dynamic Control for Digital Light Processing 3D Printing
- Open Access
- 27 December 2022
- Published by Association for Computing Machinery (ACM)
- p. 1-4
A novel scheme to developing printing protocol with the required surface roughness
3D printing has the characteristics of layer-by-layer manufacturing, which causes high surface roughness. This paper proposes a scheme to develop a printing protocol combining layer-wise and continuous printing based on the required surface roughness. It involves four modules: model slicing, printing pattern estimation, slices adjusting and printing protocol generation. Firstly, the candidate slices are obtained by model slicing based on the required surface roughness. Secondly, the printing pattern of each slice is estimated based on the max-min distance of the corresponding slice and Maximum Filled Distance (MFD) of the printing resin material. Then, the candidate slices are adjusted based on the maximum and minimum printable thickness of the printer. Finally, the printing protocol involving slice number, slice thickness, printing pattern and printing time is generated, and the surface roughness of the printed objects using the generated printing protocol can be estimated. Two printing protocols of the model cup with different required surface roughness are automatically generated. And two objects are printed based on the corresponding printing protocols. The roughness of the printed objects is measured using the roughness tester. The average roughness of the printed objects is smaller than the required roughness because the roughness of continuous printing is small. And the error between the measured and the predicted roughness is smaller than 2 µm.
- 27 December 2022
- Published by Association for Computing Machinery (ACM)
- p. 1-4
Open AccessA novel scheme to developing printing protocol with the required surface roughness
3D printing has the characteristics of layer-by-layer manufacturing, which causes high surface roughness. This paper proposes a scheme to develop a printing protocol combining layer-wise and continuous printing based on the required surface roughness. It involves four modules: model slicing, printing pattern estimation, slices adjusting and printing protocol generation. Firstly, the candidate slices are obtained by model slicing based on the required surface roughness. Secondly, the printing pattern of each slice is estimated based on the max-min distance of the corresponding slice and Maximum Filled Distance (MFD) of the printing resin material. Then, the candidate slices are adjusted based on the maximum and minimum printable thickness of the printer. Finally, the printing protocol involving slice number, slice thickness, printing pattern and printing time is generated, and the surface roughness of the printed objects using the generated printing protocol can be estimated. Two printing protocols of the model cup with different required surface roughness are automatically generated. And two objects are printed based on the corresponding printing protocols. The roughness of the printed objects is measured using the roughness tester. The average roughness of the printed objects is smaller than the required roughness because the roughness of continuous printing is small. And the error between the measured and the predicted roughness is smaller than 2 µm.
- Open Access
- 27 December 2022
- Published by Association for Computing Machinery (ACM)
- p. 1-4
Simulation of resin filling distance during the pulling-up stage for rapid DLP printing
In continuous digital light processing (DLP) 3D printing, the continuous lifting in the pulling-up stage may result in an insufficient resin filling for large-area structures, which limits its applications. Some researchers proposed a concept of maximum filling distance (MFD) and combined continuous and layer-wise printing for large-area rapid printing (LARP). However, the current MFD is estimated by experiments, which is far from optimal. In this paper, a computational fluid dynamics (CFD) analysis method is proposed to simulate the resin filling during the pulling-up stage for rapid DLP printing. Poiseuille flow is used to establish the CFD analysis models. The Volume of Fluid method is designed to simulate the resin filling behavior. The MFD can be predicted from the simulations. The validation of predicted results are fulfilled by actual printing processes. Printing experiments show that the proposed method can be successfully applied to different resins and printing parameters. It increases the efficiency of printing a new model or developing novel printing materials.
- 27 December 2022
- Published by Association for Computing Machinery (ACM)
- p. 1-4
Open AccessSimulation of resin filling distance during the pulling-up stage for rapid DLP printing
In continuous digital light processing (DLP) 3D printing, the continuous lifting in the pulling-up stage may result in an insufficient resin filling for large-area structures, which limits its applications. Some researchers proposed a concept of maximum filling distance (MFD) and combined continuous and layer-wise printing for large-area rapid printing (LARP). However, the current MFD is estimated by experiments, which is far from optimal. In this paper, a computational fluid dynamics (CFD) analysis method is proposed to simulate the resin filling during the pulling-up stage for rapid DLP printing. Poiseuille flow is used to establish the CFD analysis models. The Volume of Fluid method is designed to simulate the resin filling behavior. The MFD can be predicted from the simulations. The validation of predicted results are fulfilled by actual printing processes. Printing experiments show that the proposed method can be successfully applied to different resins and printing parameters. It increases the efficiency of printing a new model or developing novel printing materials.
- Open Access
- 6 December 2022
- Published by Association for Computing Machinery (ACM)
- p. 1-2
A novel solution to manufacturing multi-color medical preoperative models with transparent shells
Preoperative models manufactured by 3D printing technology are widely demanded in surgical procedures. Current printing methods such as Polyjet, color jet printing (CJP) and fused deposition molding (FDM) are either too expensive or of poor performance. In this paper, a novel solution is proposed. Preoperative models are first divided into internal part, such as blood vessel, and the main body. The former is printed in color and the latter is transparent. In particular, the internal part is printed using FDM. A housing template for the main body is generated by digital light processing (DLP) based on the preoperative model. After integrating the template and inner part, transparent elastomer precursor is injected and cured inside the template, leading to the formation of the transparent main body. For demonstration, a liver model is manufactured using the proposed scheme. Compared with the existing methods, our strategy could manufacture preoperative models at both high quality and affordable cost.
- 6 December 2022
- Published by Association for Computing Machinery (ACM)
- p. 1-2
Open AccessA novel solution to manufacturing multi-color medical preoperative models with transparent shells
Preoperative models manufactured by 3D printing technology are widely demanded in surgical procedures. Current printing methods such as Polyjet, color jet printing (CJP) and fused deposition molding (FDM) are either too expensive or of poor performance. In this paper, a novel solution is proposed. Preoperative models are first divided into internal part, such as blood vessel, and the main body. The former is printed in color and the latter is transparent. In particular, the internal part is printed using FDM. A housing template for the main body is generated by digital light processing (DLP) based on the preoperative model. After integrating the template and inner part, transparent elastomer precursor is injected and cured inside the template, leading to the formation of the transparent main body. For demonstration, a liver model is manufactured using the proposed scheme. Compared with the existing methods, our strategy could manufacture preoperative models at both high quality and affordable cost.
- 7 June 2017
- Published by Taylor & Francis in Journal of Modern Optics
- Vol. 64 (19) , 2066-2073
Design of an off-axis visual display based on a free-form projection screen to realize stereo vision
A free-form projection screen is designed for an off-axis visual display, which shows great potential in applications such as flight training for providing both accommodation and convergence cues for pilots. The method based on point cloud is proposed for the design of the free-form surface, and the design of the point cloud is controlled by a program written in the macro-language. In the visual display based on the free-form projection screen, when the error of the screen along Z-axis is 1 mm, the error of visual distance at each filed is less than 1%. And the resolution of the design for full field is better than 1′, which meet the requirement of resolution for human eyes.
- 7 June 2017
- Published by Taylor & Francis in Journal of Modern Optics
- Vol. 64 (19) , 2066-2073
Design of an off-axis visual display based on a free-form projection screen to realize stereo vision
A free-form projection screen is designed for an off-axis visual display, which shows great potential in applications such as flight training for providing both accommodation and convergence cues for pilots. The method based on point cloud is proposed for the design of the free-form surface, and the design of the point cloud is controlled by a program written in the macro-language. In the visual display based on the free-form projection screen, when the error of the screen along Z-axis is 1 mm, the error of visual distance at each filed is less than 1%. And the resolution of the design for full field is better than 1′, which meet the requirement of resolution for human eyes.