Jose Romero Lopera
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jose Romero Lopera has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Bernhard Auinger
Silicon Austria Labs, Graz, Austria
3 shared publications - Jasmin Grosinger
University of Siegen, Siegen, Germany
3 shared publications - Wolfgang Bosch
Institute of Microwave and Photonic Engineering, Graz University of Technology, Graz, Austria
3 shared publications - David Pommerenke
Graz University of Technology
2 shared publications Ralph Prestros
Silicon Austria Labs, Graz, Austria
2 shared publications- Richard Fischbacher
Institute of Microwave and Photonic Engineering, Graz University of Technology, Graz, Austria
2 shared publications
Latest Publications
- Open Access
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 7, 525-550
Achieving EMC Compliance in Traction Inverters via Multiobjective Optimization
Achieving first-time-right electromagnetic compatibility (EMC) is crucial in automotive industry for competitiveness. However, compliance with EM emission limits is usually evaluated through measurements on hardware prototypes, especially for complex system like electric vehicle (EV) powertrains, which include multiple components such as traction inverters (TIs) that collectively contribute to the overall emissions. Furthermore, several design goals, such as the amount of magnetic material or total installed filter capacitances, must be considered. Therefore, this paper introduces a simulation framework based on common- and differential-mode emission surrogate models with 16 design parameters. The models are derived from a circuit simulation model valid up to $30 \,\mathrm{M}\mathrm{Hz}$ and enable the prediction and optimization of conducted emissions (CEs) of traction inverters in the concept phase, prior to hardware prototyping. A Two-Level Traction Inverter (TLTI) system and CISPR 25 standard limits serve as an example. According to the feature selective validation (FSV) metric, the surrogate models achieve a worst-case accuracy rated as “very good” for CE prediction when trained on a dataset of 8064 samples. This corresponds to a spectral uncertainty of approximately $\pm 2 \,\mathrm{dB}$. With evaluation times of about $15 \,\mathrm{m}\mathrm{s}$, the presented surrogate models allow to perform 100 million TI optimizations in just $48 \,\mathrm{h}$, resulting in three selected optimal designs verified by circuit simulations. Therefore, the framework acts as a potential tool to develop first-time-right EMC and performance optimized prototypes.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 7, 525-550
Open AccessAchieving EMC Compliance in Traction Inverters via Multiobjective Optimization
Achieving first-time-right electromagnetic compatibility (EMC) is crucial in automotive industry for competitiveness. However, compliance with EM emission limits is usually evaluated through measurements on hardware prototypes, especially for complex system like electric vehicle (EV) powertrains, which include multiple components such as traction inverters (TIs) that collectively contribute to the overall emissions. Furthermore, several design goals, such as the amount of magnetic material or total installed filter capacitances, must be considered. Therefore, this paper introduces a simulation framework based on common- and differential-mode emission surrogate models with 16 design parameters. The models are derived from a circuit simulation model valid up to $30 \,\mathrm{M}\mathrm{Hz}$ and enable the prediction and optimization of conducted emissions (CEs) of traction inverters in the concept phase, prior to hardware prototyping. A Two-Level Traction Inverter (TLTI) system and CISPR 25 standard limits serve as an example. According to the feature selective validation (FSV) metric, the surrogate models achieve a worst-case accuracy rated as “very good” for CE prediction when trained on a dataset of 8064 samples. This corresponds to a spectral uncertainty of approximately $\pm 2 \,\mathrm{dB}$. With evaluation times of about $15 \,\mathrm{m}\mathrm{s}$, the presented surrogate models allow to perform 100 million TI optimizations in just $48 \,\mathrm{h}$, resulting in three selected optimal designs verified by circuit simulations. Therefore, the framework acts as a potential tool to develop first-time-right EMC and performance optimized prototypes.
- Open Access
- 29 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Radio Frequency Identification
- Vol. 8, 713-723
Communication and Power Transfer Analysis of Interfering Magnetically Resonant Coupled Systems
This work presents, for the first time, a communication and power transfer analysis of interfering wireless power transfer (WPT) and near-field communication (NFC) systems. The communication analysis is conducted by investigating the NFC tag-to-reader communication quality in the digital baseband while being interfered with by WPT. The power transfer analysis is conducted by investigating the maximum power transferred and WPT efficiency η while being affected by the passive loading effects of the NFC prototype system. Inductive decoupling techniques are applied to improve the communication quality and WPT performance. Good communication quality was achieved with at least 60% inductive decoupling. A system-level adjustment of the communication signal demodulation achieved further communication quality improvements, requiring only 15% inductive decoupling. The WPT performance was improved by inductive decoupling, shown by an improved maximum power transfer of up to 27% and an improved WPT efficiency η from 0.42 to 0.67. Additionally, inductive decoupling reduced the chance of the WPT system damaging the NFC system due to too much energy being delivered. These investigations were conducted using time-efficient broadband circuit-level simulations and measurement-verified broadband equivalent circuit coil models.
- 29 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Radio Frequency Identification
- Vol. 8, 713-723
Open AccessCommunication and Power Transfer Analysis of Interfering Magnetically Resonant Coupled Systems
This work presents, for the first time, a communication and power transfer analysis of interfering wireless power transfer (WPT) and near-field communication (NFC) systems. The communication analysis is conducted by investigating the NFC tag-to-reader communication quality in the digital baseband while being interfered with by WPT. The power transfer analysis is conducted by investigating the maximum power transferred and WPT efficiency η while being affected by the passive loading effects of the NFC prototype system. Inductive decoupling techniques are applied to improve the communication quality and WPT performance. Good communication quality was achieved with at least 60% inductive decoupling. A system-level adjustment of the communication signal demodulation achieved further communication quality improvements, requiring only 15% inductive decoupling. The WPT performance was improved by inductive decoupling, shown by an improved maximum power transfer of up to 27% and an improved WPT efficiency η from 0.42 to 0.67. Additionally, inductive decoupling reduced the chance of the WPT system damaging the NFC system due to too much energy being delivered. These investigations were conducted using time-efficient broadband circuit-level simulations and measurement-verified broadband equivalent circuit coil models.
- Open Access
- 11 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (1) , 4-8
Communication Quality Analysis for WPT and NFC Systems via Broadband Equivalent Circuit Models
This letter presents a novel full-system communication quality analysis of a wireless power transfer (WPT) and near-field communication (NFC) system. The analysis is conducted via a thoroughly verified broadband equivalent circuit (EC) model of a WPT and NFC system prototype. Such an EC model can accelerate the iterative system design process for systems with interoperating or coexisting WPT and NFC interfaces. The EC model is verified by measurements of a prototype. EC model and measurements agree excellently by comparing impedance parameters, single-sided frequency spectra, and the signal constellation diagram of the NFC tag-to-reader communication signal. The NFC communication quality analysis shows a severe impairment of the NFC tag-to-reader communication by the WPT system.
- 11 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (1) , 4-8
Open AccessCommunication Quality Analysis for WPT and NFC Systems via Broadband Equivalent Circuit Models
This letter presents a novel full-system communication quality analysis of a wireless power transfer (WPT) and near-field communication (NFC) system. The analysis is conducted via a thoroughly verified broadband equivalent circuit (EC) model of a WPT and NFC system prototype. Such an EC model can accelerate the iterative system design process for systems with interoperating or coexisting WPT and NFC interfaces. The EC model is verified by measurements of a prototype. EC model and measurements agree excellently by comparing impedance parameters, single-sided frequency spectra, and the signal constellation diagram of the NFC tag-to-reader communication signal. The NFC communication quality analysis shows a severe impairment of the NFC tag-to-reader communication by the WPT system.
- Open Access
- 13 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 3 (1) , 193-226
Microwave-Enabled Wearables: Underpinning Technologies, Integration Platforms, and Next-Generation Roadmap
This paper presents a holistic and authoritative review of the role of microwave technologies in enabling a new generation of wearable devices. A human-centric Internet of Things (IoT) covering remote healthcare, distributed sensing, and consumer electronics, calls for high-performance wearable devices integrated into clothing, which require interdisciplinary research efforts to emerge. Microwaves, the “interconnect” of wireless networks, can enable, rather than solely connect, the next generation of autonomous, sustainable, and wearable-friendly electronics. First, enabling technologies including wireless power transmission and RF energy harvesting, backscattering and passive communication, RFID, and electromagnetic sensing are reviewed. We then discuss the key integration platforms, covering smart fabrics and electronic textiles, additive manufacturing, printed electronics, natively-flexible and organic RF semiconductors, and fully-integrated CMOS systems, where opportunities for hybrid integration are highlighted. The emerging research trends, from mmWave 6G, RF sensing and imaging, to healthcare applications including neural implants, drug delivery, and safety upon exposure to microwaves are re-visited and discussed, presenting a future roadmap for interdisciplinary research towards sustainable and reliable next-generation wearables.
- 13 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 3 (1) , 193-226
Open AccessMicrowave-Enabled Wearables: Underpinning Technologies, Integration Platforms, and Next-Generation Roadmap
This paper presents a holistic and authoritative review of the role of microwave technologies in enabling a new generation of wearable devices. A human-centric Internet of Things (IoT) covering remote healthcare, distributed sensing, and consumer electronics, calls for high-performance wearable devices integrated into clothing, which require interdisciplinary research efforts to emerge. Microwaves, the “interconnect” of wireless networks, can enable, rather than solely connect, the next generation of autonomous, sustainable, and wearable-friendly electronics. First, enabling technologies including wireless power transmission and RF energy harvesting, backscattering and passive communication, RFID, and electromagnetic sensing are reviewed. We then discuss the key integration platforms, covering smart fabrics and electronic textiles, additive manufacturing, printed electronics, natively-flexible and organic RF semiconductors, and fully-integrated CMOS systems, where opportunities for hybrid integration are highlighted. The emerging research trends, from mmWave 6G, RF sensing and imaging, to healthcare applications including neural implants, drug delivery, and safety upon exposure to microwaves are re-visited and discussed, presenting a future roadmap for interdisciplinary research towards sustainable and reliable next-generation wearables.
- 23 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
An Asymmetrical Single-stage GaN MMIC DPA at 25 GHz Implementing Dynamic Input Power Division for Enhanced PAE at 7.6 dB OBO
This paper presents an asymmetric single-stage Doherty power amplifier (DPA) in MMIC form using OMMIC GaN transistors operating at 25 GHz. The DPA implements a dynamic input power division technique in contrast with the more conventional fixed input power division. The technique mentioned above splits the input power by sending most of the power to the main PA when the peak PA is not conducting. Therefore, the power sent to the peak PA gradually increases after it reaches a certain input power level and starts conducting. This behavior is achieved by taking advantage of the non-linear behavior that characterizes the gate capacitance of a transistor in class C operation. As a result, the input impedance of the peak PA will be matched appropriately for saturation. However, it will show a higher real-valued impedance at power levels below back-off (BO) operation. This will have a substantial positive impact on the PAE and small-signal gain degradation at BO that would occur if fixed input power division was to be used. The DPA reaches a maximum output power of 33.8 dBm at a PAE of 28% and efficiency of 22% for 7.6dB OBO, keeping a level of PAE over 16% over the 7.6dB to maximum output power range.
- 23 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
An Asymmetrical Single-stage GaN MMIC DPA at 25 GHz Implementing Dynamic Input Power Division for Enhanced PAE at 7.6 dB OBO
This paper presents an asymmetric single-stage Doherty power amplifier (DPA) in MMIC form using OMMIC GaN transistors operating at 25 GHz. The DPA implements a dynamic input power division technique in contrast with the more conventional fixed input power division. The technique mentioned above splits the input power by sending most of the power to the main PA when the peak PA is not conducting. Therefore, the power sent to the peak PA gradually increases after it reaches a certain input power level and starts conducting. This behavior is achieved by taking advantage of the non-linear behavior that characterizes the gate capacitance of a transistor in class C operation. As a result, the input impedance of the peak PA will be matched appropriately for saturation. However, it will show a higher real-valued impedance at power levels below back-off (BO) operation. This will have a substantial positive impact on the PAE and small-signal gain degradation at BO that would occur if fixed input power division was to be used. The DPA reaches a maximum output power of 33.8 dBm at a PAE of 28% and efficiency of 22% for 7.6dB OBO, keeping a level of PAE over 16% over the 7.6dB to maximum output power range.