Yani Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yani Zhang has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Laifei Cheng
National Key Laboratory of Thermostructure Composite Materials, Northwestern Polytechnical University, Xi'an, shaanxi 710072, China
3 shared publicationsLitong Zhang
National Key Laboratory of Thermostructure Composite Materials, Northwestern Polytechnical University, Xi'an, shaanxi 710072, China
3 shared publicationsYongdong Xu
National Key Laboratory of Thermostructure Composite Materials, Northwestern Polytechnical University, Xi'an, shaanxi 710072, China
3 shared publicationsDonglin Zhao
National Key Laboratory of Thermostructure Composite Materials, Northwestern Polytechnical University, Xi'an, shaanxi 710072, China
1 shared publication
Latest Publications
- 17 December 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 91 (1) , 291-295
Stress‐Oxidation Behavior of a Carbon/Silicon Carbide Composite in a High‐Temperature Combustion Environment
A carbon/silicon carbide composite with a silicon carbide coating was prepared by chemical vapor infiltration. Stressed oxidation testing was performed on the composites in a self‐built high‐temperature combustion environment. The gas in this environment contained oxygen, steam, carbon dioxide, and some nitrogen. Test conditions were controlled at temperatures of 1300°, 1500°, and 1800°C, and the stress was sustained at 40, 80, 120, 160, and 200 MPa. The effect of combustion environment and applied load on stress‐oxidation behavior was discussed by analyzing the residual strength and weight loss. The morphology of the fracture surface of the tested specimens was observed by scanning electron microscopy. The high‐temperature combustion environment and the high sustained stress above 80 MPa enhanced the material failure and led to strength reduction by determining crack openings and thus oxidation of fibers. However, sustained stress below 80 MPa resulted in no strength degradation after exposure for 10 min at 1500°C.
- 17 December 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 91 (1) , 291-295
Stress‐Oxidation Behavior of a Carbon/Silicon Carbide Composite in a High‐Temperature Combustion Environment
A carbon/silicon carbide composite with a silicon carbide coating was prepared by chemical vapor infiltration. Stressed oxidation testing was performed on the composites in a self‐built high‐temperature combustion environment. The gas in this environment contained oxygen, steam, carbon dioxide, and some nitrogen. Test conditions were controlled at temperatures of 1300°, 1500°, and 1800°C, and the stress was sustained at 40, 80, 120, 160, and 200 MPa. The effect of combustion environment and applied load on stress‐oxidation behavior was discussed by analyzing the residual strength and weight loss. The morphology of the fracture surface of the tested specimens was observed by scanning electron microscopy. The high‐temperature combustion environment and the high sustained stress above 80 MPa enhanced the material failure and led to strength reduction by determining crack openings and thus oxidation of fibers. However, sustained stress below 80 MPa resulted in no strength degradation after exposure for 10 min at 1500°C.
- 26 June 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 90 (8) , 2630-2633
Experimental Simulation of the Space Re‐Entry Environment for a Carbon/Silicon Carbide Compsite and the Effect on its Properties
An experimental simulation method of space re‐entry environment was presented to investigate a carbon/silicon carbide composite and the effect on its properties. The re‐entry environment is simulated by controlling the thermal environment and the stress environment. The thermal environment is provided with a high enthalpy combustion chamber with a temperature range of 600°–1800°C and a partial pressure of oxygen of 10–30 kPa. The stress environment can realize both loading and rotating effects with a maximum torque of 150 N·m and a minimum rotation velocity of 32 rpm. Multipurpose testing of a carbon/silicon carbide composite during re‐entry can be achieved by this method, such as hot joining, stress‐oxidation, creep, and friction behavior.
- 26 June 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 90 (8) , 2630-2633
Experimental Simulation of the Space Re‐Entry Environment for a Carbon/Silicon Carbide Compsite and the Effect on its Properties
An experimental simulation method of space re‐entry environment was presented to investigate a carbon/silicon carbide composite and the effect on its properties. The re‐entry environment is simulated by controlling the thermal environment and the stress environment. The thermal environment is provided with a high enthalpy combustion chamber with a temperature range of 600°–1800°C and a partial pressure of oxygen of 10–30 kPa. The stress environment can realize both loading and rotating effects with a maximum torque of 150 N·m and a minimum rotation velocity of 32 rpm. Multipurpose testing of a carbon/silicon carbide composite during re‐entry can be achieved by this method, such as hot joining, stress‐oxidation, creep, and friction behavior.
- 30 March 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 90 (4) , 1139-1145
High‐Load Friction Behavior of a Hinge Bearing Based on a Carbon/Silicon Carbide Composite
Two‐dimensional carbon fiber‐reinforced silicon carbide matrix (C/SiC) composites used for hinge bearing were prepared by chemical vapor infiltration. The testing and results of unlubricated friction behavior of hinge bearing under high‐load transmitting motion was investigated. The effects of load on friction behavior between different sliding couple were analyzed. Finally, worn surfaces and debris were observed by scanning electron microscopy to study the wear mechanism. A constant friction coefficient between self‐mated C/SiC composites of 0.68 was obtained on increasing load up to about 5800 N. Excellent wear resistance and load‐carrying ability was demonstrated by low wear and especially small deformation.
- 30 March 2007
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 90 (4) , 1139-1145
High‐Load Friction Behavior of a Hinge Bearing Based on a Carbon/Silicon Carbide Composite
Two‐dimensional carbon fiber‐reinforced silicon carbide matrix (C/SiC) composites used for hinge bearing were prepared by chemical vapor infiltration. The testing and results of unlubricated friction behavior of hinge bearing under high‐load transmitting motion was investigated. The effects of load on friction behavior between different sliding couple were analyzed. Finally, worn surfaces and debris were observed by scanning electron microscopy to study the wear mechanism. A constant friction coefficient between self‐mated C/SiC composites of 0.68 was obtained on increasing load up to about 5800 N. Excellent wear resistance and load‐carrying ability was demonstrated by low wear and especially small deformation.