Junjie Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Junjie Jiang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Wentao Zhai
School of Materials Science and Engineering Sun Yat‐sen University Guangzhou Guangdong Province China
10 shared publications - Yaozong Li
School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou 510275, China
6 shared publications - Liang Wang
School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou 510275, China
5 shared publications Hanyi Huang
School of Materials Science and Engineering Sun Yat‐sen University Guangzhou Guangdong Province China
4 shared publicationsZiwei Qin
School of Materials Science and Engineering Sun Yat‐sen University Guangzhou Guangdong Province China
4 shared publicationsFangwei Tian
3 shared publications
Latest Publications
- 21 August 2026
- Published by Wiley in Macromolecular Rapid Communications
- Vol. 47 (20) , e70411
A Review on the Study of Fiber‐Reinforced Thermoplastic Elastomer Composites
Fiber‐reinforced elastomers can significantly enhance mechanical strength while retaining material softness, thereby expanding the application scope of elastomeric materials in scenarios requiring both high flexibility and high strength. Compared with thermoplastic polymers and ceramic materials, elastomers exhibit low modulus and high fracture strain, which result in more complex fiber–matrix interfacial behaviors. This review systematically elucidates the intrinsic relationships between microscopic stress transfer mechanisms and macroscopic mechanical properties in fiber‐reinforced elastomers, summarizes research progress in this field over the past two decades, and highlights the effects of various reinforcement strategies on performance optimization, providing a theoretical basis for the design and development of next‐generation high‐performance fiber‐reinforced elastomers.
- 21 August 2026
- Published by Wiley in Macromolecular Rapid Communications
- Vol. 47 (20) , e70411
A Review on the Study of Fiber‐Reinforced Thermoplastic Elastomer Composites
Fiber‐reinforced elastomers can significantly enhance mechanical strength while retaining material softness, thereby expanding the application scope of elastomeric materials in scenarios requiring both high flexibility and high strength. Compared with thermoplastic polymers and ceramic materials, elastomers exhibit low modulus and high fracture strain, which result in more complex fiber–matrix interfacial behaviors. This review systematically elucidates the intrinsic relationships between microscopic stress transfer mechanisms and macroscopic mechanical properties in fiber‐reinforced elastomers, summarizes research progress in this field over the past two decades, and highlights the effects of various reinforcement strategies on performance optimization, providing a theoretical basis for the design and development of next‐generation high‐performance fiber‐reinforced elastomers.
- Open Access
Foam Rubber-Based Three-Layer Flexible Composite for High-Efficiency Infrared Stealth and Joule Heating
With the rapid development of infrared detection methods and military surveillance technologies, flexible and wearable infrared stealth materials (ISM) have attracted increasing attention. Inspired by the layered structure of penguins’ fat–feather–oil, this study prepared a three-layer MXene/waterborne polyurethane (WPU)-foam rubber-phase change microcapsule (PCM)/WPU composite material (M-F-P) via the solution blending and doctor-blading method. The outermost layer of the M-F-P composite is an MXene/WPU conductive film, which features a low infrared emissivity and Joule heating performance to adapt to suddenly cold environments. The porous foam rubber in the middle layer provides excellent thermal insulation performance, which effectively inhibits heat conduction and enhances infrared stealth efficiency. Meanwhile, as a four-directional elastic material, it exhibits deformation recovery capability in both the warp and weft directions as well as the 45° direction. The bottom layer of the PCM/WPU film has a phase change enthalpy of 154.3 J/g and possesses efficient thermal management capability. It achieves dynamic thermal regulation through the cycle of heat absorption at high temperatures and heat release at low temperatures.
Open AccessFoam Rubber-Based Three-Layer Flexible Composite for High-Efficiency Infrared Stealth and Joule Heating
With the rapid development of infrared detection methods and military surveillance technologies, flexible and wearable infrared stealth materials (ISM) have attracted increasing attention. Inspired by the layered structure of penguins’ fat–feather–oil, this study prepared a three-layer MXene/waterborne polyurethane (WPU)-foam rubber-phase change microcapsule (PCM)/WPU composite material (M-F-P) via the solution blending and doctor-blading method. The outermost layer of the M-F-P composite is an MXene/WPU conductive film, which features a low infrared emissivity and Joule heating performance to adapt to suddenly cold environments. The porous foam rubber in the middle layer provides excellent thermal insulation performance, which effectively inhibits heat conduction and enhances infrared stealth efficiency. Meanwhile, as a four-directional elastic material, it exhibits deformation recovery capability in both the warp and weft directions as well as the 45° direction. The bottom layer of the PCM/WPU film has a phase change enthalpy of 154.3 J/g and possesses efficient thermal management capability. It achieves dynamic thermal regulation through the cycle of heat absorption at high temperatures and heat release at low temperatures.
- 4 May 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (19)
Fabrication of Low‐Density Ethylene−Vinyl Acetate/Olefin Block Copolymer Foam with Well Rebound Properties Blown with Mixed N2/CO2
Thermoplastic elastomer foams, such as ethylene−vinyl acetate (EVA) foams, have received extensive attention for their soft touching, low‐density, and excellent mechanical properties and have been emerging in lightweight footwear. However, the EVA foam suffers from its inadequate rebound resilience properties and poor thermal stability due to the low melting point. Herein, olefin block copolymer (OBC) with excellent rebound properties and high melting peak temperature of 120 °C is introduced into the EVA matrix to improve its foaming behavior and foam properties. A series of lightweight EVA/OBC composite foams with adjustable cellular structures are prepared by supercritical mixed N2/CO2. It is worth noting that the foaming temperature windows are greatly improved under the action of OBC, and an extremely low‐density as low as 0.06 g cm−3 is achieved. In addition, the as‐prepared EVA/OBC foams exhibit the improved foam shrinkage resistance, resulting from the rapid crystallization ability of OBC phase. Furthermore, the residual strain and hysteresis loss ratio of as‐prepared elastomer foams are as low as 1.56 and 12.95%, respectively. These distinct advantages together with the green foaming process make the EVA/OBC elastomer foams very promising toward high‐performance flexible cellular polymeric materials.
- 4 May 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (19)
Fabrication of Low‐Density Ethylene−Vinyl Acetate/Olefin Block Copolymer Foam with Well Rebound Properties Blown with Mixed N2/CO2
Thermoplastic elastomer foams, such as ethylene−vinyl acetate (EVA) foams, have received extensive attention for their soft touching, low‐density, and excellent mechanical properties and have been emerging in lightweight footwear. However, the EVA foam suffers from its inadequate rebound resilience properties and poor thermal stability due to the low melting point. Herein, olefin block copolymer (OBC) with excellent rebound properties and high melting peak temperature of 120 °C is introduced into the EVA matrix to improve its foaming behavior and foam properties. A series of lightweight EVA/OBC composite foams with adjustable cellular structures are prepared by supercritical mixed N2/CO2. It is worth noting that the foaming temperature windows are greatly improved under the action of OBC, and an extremely low‐density as low as 0.06 g cm−3 is achieved. In addition, the as‐prepared EVA/OBC foams exhibit the improved foam shrinkage resistance, resulting from the rapid crystallization ability of OBC phase. Furthermore, the residual strain and hysteresis loss ratio of as‐prepared elastomer foams are as low as 1.56 and 12.95%, respectively. These distinct advantages together with the green foaming process make the EVA/OBC elastomer foams very promising toward high‐performance flexible cellular polymeric materials.
- Open Access
Shortening the Saturation Time of PBAT Sheet Foaming via the Pre-Introducing of Microporous Structures
Poly (butylene adipate-co-terephthalate) (PBAT) foam sheets prepared by foaming supercritical fluids are characterized by high resilience, homogeneous cellular structure, and well-defined biodegradability. However, the inert chemical structure and the rigid hard segments restrict the diffusion of CO2 within the PBAT matrix, resulting in extremely long gas saturation times as long as 9 h at a thickness of 12 mm. In this study, microporous structures were pre-introduced into the PBAT matrix to provide a fast gas diffusion pathway during the saturation process. After 2 h of saturation, PBAT foam sheets with expansion ratio of 10 to 13.8 times were prepared. The interaction of CO2 with PBAT was systematically investigated, and the CO2 sorption process was evaluated kinetically and thermodynamically using the Fickian diffusion theory. The solubility and diffusion rate of CO2 in pretreated PBAT sheets with different microporous sizes and densities were investigated, and the effects of pretreatment strategies on the foaming behavior and cell structure of PBAT foam sheets were discussed. The introduction of a microporous structure not only reduces saturation time but also enhances solubility, enabling the successful preparation of soft foams with high expansion ratios and resilience. After undergoing foaming treatment, the PBAT pretreated sheets with a 10 μm microporous structure and a density of 0.45 g/cm3 demonstrated improved mechanical properties: their hardness decreased to 35 C while resilience increased to 58%, reflecting enhanced elastic recovery capabilities. The pretreatment method, which increases the diffusion rate of CO2 in PBAT sheets, offers a straightforward approach that provides valuable insights into achieving rapid and efficient foaming of thick PBAT sheets in industrial applications.
Open AccessShortening the Saturation Time of PBAT Sheet Foaming via the Pre-Introducing of Microporous Structures
Poly (butylene adipate-co-terephthalate) (PBAT) foam sheets prepared by foaming supercritical fluids are characterized by high resilience, homogeneous cellular structure, and well-defined biodegradability. However, the inert chemical structure and the rigid hard segments restrict the diffusion of CO2 within the PBAT matrix, resulting in extremely long gas saturation times as long as 9 h at a thickness of 12 mm. In this study, microporous structures were pre-introduced into the PBAT matrix to provide a fast gas diffusion pathway during the saturation process. After 2 h of saturation, PBAT foam sheets with expansion ratio of 10 to 13.8 times were prepared. The interaction of CO2 with PBAT was systematically investigated, and the CO2 sorption process was evaluated kinetically and thermodynamically using the Fickian diffusion theory. The solubility and diffusion rate of CO2 in pretreated PBAT sheets with different microporous sizes and densities were investigated, and the effects of pretreatment strategies on the foaming behavior and cell structure of PBAT foam sheets were discussed. The introduction of a microporous structure not only reduces saturation time but also enhances solubility, enabling the successful preparation of soft foams with high expansion ratios and resilience. After undergoing foaming treatment, the PBAT pretreated sheets with a 10 μm microporous structure and a density of 0.45 g/cm3 demonstrated improved mechanical properties: their hardness decreased to 35 C while resilience increased to 58%, reflecting enhanced elastic recovery capabilities. The pretreatment method, which increases the diffusion rate of CO2 in PBAT sheets, offers a straightforward approach that provides valuable insights into achieving rapid and efficient foaming of thick PBAT sheets in industrial applications.
- Open Access
The Quantitative Evaluation of the Cell Structure Uniformity of Microcellular TPU with Low Porosity via a Digital Image Processing Method
The cell structure uniformity of microcellular polymers significantly impacts material performance, especially for low-porosity microcellular TPU used in chip polishing. The distribution of the cell structure of polishing pads directly affects the removal rate and process repeatability. Despite its importance, no quantitative method for evaluating cell structure uniformity has been reported in the literature. In this study, a digital image processing method that involves morphological operations of scanning electron microscopy (SEM) images, binarization, and cell localization, and the statistical evaluation of cell structure parameters was established to evaluate cell structure uniformity. A quantitative metric, the cell structure uniformity index (CUI), was calculated based on cell structure indices, incorporating the cell size index (Ud), the cell number index (Un), and the cell local spacing index (Ur). By establishing an ideal model and analyzing representative SEM images, the effectiveness and efficiency of the method for evaluating cell structure uniformity of microcellular TPU were successfully validated. The results demonstrated that low-porosity TPU foams exhibited relatively low cell structure uniformity compared to the ideal model. The heterogeneous nucleation process in TPU caused non-uniform cell structures due to the temporal and spatial non-homogeneities during the early cell nucleation process. As the cells grew, they merged and reduced the distance between them, resulting in improved cell structure uniformity.
Open AccessThe Quantitative Evaluation of the Cell Structure Uniformity of Microcellular TPU with Low Porosity via a Digital Image Processing Method
The cell structure uniformity of microcellular polymers significantly impacts material performance, especially for low-porosity microcellular TPU used in chip polishing. The distribution of the cell structure of polishing pads directly affects the removal rate and process repeatability. Despite its importance, no quantitative method for evaluating cell structure uniformity has been reported in the literature. In this study, a digital image processing method that involves morphological operations of scanning electron microscopy (SEM) images, binarization, and cell localization, and the statistical evaluation of cell structure parameters was established to evaluate cell structure uniformity. A quantitative metric, the cell structure uniformity index (CUI), was calculated based on cell structure indices, incorporating the cell size index (Ud), the cell number index (Un), and the cell local spacing index (Ur). By establishing an ideal model and analyzing representative SEM images, the effectiveness and efficiency of the method for evaluating cell structure uniformity of microcellular TPU were successfully validated. The results demonstrated that low-porosity TPU foams exhibited relatively low cell structure uniformity compared to the ideal model. The heterogeneous nucleation process in TPU caused non-uniform cell structures due to the temporal and spatial non-homogeneities during the early cell nucleation process. As the cells grew, they merged and reduced the distance between them, resulting in improved cell structure uniformity.
- Open Access
Comparative Study of the Foaming Behavior of Ethylene–Vinyl Acetate Copolymer Foams Fabricated Using Chemical and Physical Foaming Processes
Ethylene–vinyl acetate copolymer (EVA), a crucial elastomeric resin, finds extensive application in the footwear industry. Conventional chemical foaming agents, including azodicarbonamide and 4,4′-oxybis(benzenesulfonyl hydrazide), have been identified as environmentally problematic. Hence, this study explores the potential of physical foaming of EVA using supercritical nitrogen as a sustainable alternative, garnering considerable interest in both academia and industry. The EVA formulations and processing parameters were optimized and EVA foams with densities between 0.15 and 0.25 g/cm3 were produced. Key findings demonstrate that physical foaming not only reduces environmental impact but also enhances product quality by a uniform cell structure with small cell size (50–100 μm), a wide foaming temperature window (120–180 °C), and lower energy consumption. The research further elucidates the mechanisms of cell nucleation and growth within the crosslinked EVA network, highlighting the critical role of blowing agent dispersion and localized crosslinking around nucleated cells in defining the foam’s cellular morphology. These findings offer valuable insights for producing EVA foams with a more controllable cellular structure, utilizing physical foaming techniques.
Open AccessComparative Study of the Foaming Behavior of Ethylene–Vinyl Acetate Copolymer Foams Fabricated Using Chemical and Physical Foaming Processes
Ethylene–vinyl acetate copolymer (EVA), a crucial elastomeric resin, finds extensive application in the footwear industry. Conventional chemical foaming agents, including azodicarbonamide and 4,4′-oxybis(benzenesulfonyl hydrazide), have been identified as environmentally problematic. Hence, this study explores the potential of physical foaming of EVA using supercritical nitrogen as a sustainable alternative, garnering considerable interest in both academia and industry. The EVA formulations and processing parameters were optimized and EVA foams with densities between 0.15 and 0.25 g/cm3 were produced. Key findings demonstrate that physical foaming not only reduces environmental impact but also enhances product quality by a uniform cell structure with small cell size (50–100 μm), a wide foaming temperature window (120–180 °C), and lower energy consumption. The research further elucidates the mechanisms of cell nucleation and growth within the crosslinked EVA network, highlighting the critical role of blowing agent dispersion and localized crosslinking around nucleated cells in defining the foam’s cellular morphology. These findings offer valuable insights for producing EVA foams with a more controllable cellular structure, utilizing physical foaming techniques.
- Open Access
Polymer Bead Foams: A Review on Foam Preparation, Molding, and Interbead Bonding Mechanism
The diverse physical appearances and wide density range of polymer bead foams offer immense potential in various applications and future advancements. The multiscale and multilevel structural features of bead foams involve many fundamental scientific topics. This review presents a comprehensive overview of recent progress in the preparation and molding techniques of bead foams. Firstly, it gives a comparative analysis on the bead foam characteristics of distinct polymers. Then, a summary and comparison of molding techniques employed for fabricating bead foam parts are provided. Beyond traditional methods like steam-chest molding (SCM) and adhesive-assisted molding (AAM), emerging techniques like in-mold foaming and molding (IMFM) and microwave selective sintering (MSS) are highlighted. Lastly, the bonding mechanisms behind these diverse molding methods are discussed.
Open AccessPolymer Bead Foams: A Review on Foam Preparation, Molding, and Interbead Bonding Mechanism
The diverse physical appearances and wide density range of polymer bead foams offer immense potential in various applications and future advancements. The multiscale and multilevel structural features of bead foams involve many fundamental scientific topics. This review presents a comprehensive overview of recent progress in the preparation and molding techniques of bead foams. Firstly, it gives a comparative analysis on the bead foam characteristics of distinct polymers. Then, a summary and comparison of molding techniques employed for fabricating bead foam parts are provided. Beyond traditional methods like steam-chest molding (SCM) and adhesive-assisted molding (AAM), emerging techniques like in-mold foaming and molding (IMFM) and microwave selective sintering (MSS) are highlighted. Lastly, the bonding mechanisms behind these diverse molding methods are discussed.
- Open Access
- 7 September 2023
- Published by MDPI AG in Preprints.org
Polymer Bead Foams: A Review on Foam Preparation, Molding, and Inter-Bead Bonding Mechanism
The diverse physical appearances and wide density range of polymer bead foams offer immense potential across various applications and future advancements. The multi-scale and multi-level structural features of bead foams involve many fundamental scientific topics. This review presents a comprehensive overview of recent progress in bead foams preparation and molding techniques. Initially, a comparative analysis is conducted among bead foam characteristics of distinct polymers, based on their unique properties. Subsequently, a summary and comparison of molding processes employed for fabricating bead foam parts are provided. Beyond traditional methods like steam-chest molding (SCM) and adhesive-assisted molding (AAM), emerging techniques like in-mold foaming and molding (IMFM) and microwave selective sintering (MSS) are highlighted. Lastly, the bonding mechanisms behind the diverse molding methods are discussed.
- 7 September 2023
- Published by MDPI AG in Preprints.org
Open AccessPolymer Bead Foams: A Review on Foam Preparation, Molding, and Inter-Bead Bonding Mechanism
The diverse physical appearances and wide density range of polymer bead foams offer immense potential across various applications and future advancements. The multi-scale and multi-level structural features of bead foams involve many fundamental scientific topics. This review presents a comprehensive overview of recent progress in bead foams preparation and molding techniques. Initially, a comparative analysis is conducted among bead foam characteristics of distinct polymers, based on their unique properties. Subsequently, a summary and comparison of molding processes employed for fabricating bead foam parts are provided. Beyond traditional methods like steam-chest molding (SCM) and adhesive-assisted molding (AAM), emerging techniques like in-mold foaming and molding (IMFM) and microwave selective sintering (MSS) are highlighted. Lastly, the bonding mechanisms behind the diverse molding methods are discussed.