Dong In Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dong In Lee has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Jongtae Lee
Transportation Pollution Research Center, National Institute of Environmental Research, Incheon 22689, Republic of Korea
3 shared publications - Jinkyu Park
Division of Marine System Engineering, Mokpo National Maritime University, Mokpo 58628, Republic of Korea
2 shared publications - Jungmo Oh
Division of Marine System Engineering, Mokpo National Maritime University, Mokpo 58628, Republic of Korea
2 shared publications - Junhong Park
Transportation Pollution Research Center, National Institute of Environmental Research, Incheon 22689, Republic of Korea
2 shared publications - Myunghwan Shin
Nakdong River Basin Environmental Office, Changwon 51439, Republic of Korea
2 shared publications - Myunghwan Shin2 shared publications
Latest Publications
- Open Access
- 15 July 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (14) , 6134
Carbon Dioxide Emission Characteristics and Operation Condition Optimization for Slow-Speed and High-Speed Ship Engines
Greenhouse gas emissions from ships are estimated to be approximately 1002 million tons per year; this is the largest carbon dioxide (CO2) emission source among nonroad transportation. Previous studies have generally estimated CO2 emissions using fuel- or power-based emission factors based on fuel consumption or engine power. In this study, CO2 emissions from vessels were measured using a portable emission measurement system. Emission characteristics were analyzed according to the vessel’s operation conditions and compared with the results of other studies. Generally, the higher the rpm value, the more CO2 is emitted, and the emissions at the maximum rpm differ depending on the type and size of the engine. In order to minimize the emissions by ships, those from high seas should be reduced rather than nearby ports. In addition, a method of establishing optimal operating conditions in consideration of economic and environmental perspectives was proposed. Fuel-based emission factors elicited in this study were constant regardless of engine rpm. The fuel-based emission factors of each engine were found to be similar at 3144.22 and 3150.58 kg-CO2/tonne-fuel. Therefore, distinguishing CO2 emission factors according to engine type is not necessary, and additional research is required to understand the emission factors of each fuel type.
- 15 July 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (14) , 6134
Open AccessCarbon Dioxide Emission Characteristics and Operation Condition Optimization for Slow-Speed and High-Speed Ship Engines
Greenhouse gas emissions from ships are estimated to be approximately 1002 million tons per year; this is the largest carbon dioxide (CO2) emission source among nonroad transportation. Previous studies have generally estimated CO2 emissions using fuel- or power-based emission factors based on fuel consumption or engine power. In this study, CO2 emissions from vessels were measured using a portable emission measurement system. Emission characteristics were analyzed according to the vessel’s operation conditions and compared with the results of other studies. Generally, the higher the rpm value, the more CO2 is emitted, and the emissions at the maximum rpm differ depending on the type and size of the engine. In order to minimize the emissions by ships, those from high seas should be reduced rather than nearby ports. In addition, a method of establishing optimal operating conditions in consideration of economic and environmental perspectives was proposed. Fuel-based emission factors elicited in this study were constant regardless of engine rpm. The fuel-based emission factors of each engine were found to be similar at 3144.22 and 3150.58 kg-CO2/tonne-fuel. Therefore, distinguishing CO2 emission factors according to engine type is not necessary, and additional research is required to understand the emission factors of each fuel type.
- Open Access
- 1 January 2023
- Published by The Korean Society of Automotive Engineers in Transaction of the Korean Society of Automotive Engineers
- Vol. 31 (1) , 11-18
A Study on a Comparison of Greenhouse Gas Emission Results According to Actual Measurement and Domestic Calculation Method for Medium-sized Diesel Engine of Vessel
- 1 January 2023
- Published by The Korean Society of Automotive Engineers in Transaction of the Korean Society of Automotive Engineers
- Vol. 31 (1) , 11-18
Open AccessA Study on a Comparison of Greenhouse Gas Emission Results According to Actual Measurement and Domestic Calculation Method for Medium-sized Diesel Engine of Vessel
- Open Access
Characteristics of Real-World Gaseous Emissions from Construction Machinery
In Korea’s air pollutant inventory, construction machinery is a major emission source in the non-road sector. Since 2004, the Korean government has introduced and reinforced emission regulations to reduce the air pollutants emitted from their diesel engines. Since the engine dynamometer test method used in emission regulations has limitations in reflecting emission characteristics under the diverse working conditions of construction machinery, it is necessary to examine the effectiveness of emission regulations and the validity of the emission factors applied as inputs to the air pollutants inventory. This could be done by evaluating engine operation and emission characteristics under real-world working conditions. In this study, 14 units were selected among the excavators, wheel loaders, and forklifts that represent approximately 90% of the registered construction machines in Korea. They were equipped with a portable emission measurement system (PEMS) to measure gaseous emissions and collect engine data under various real-world working conditions. With the reinforcement of emission regulations for the construction machinery from K-tier3 to K-tier4 in Korea, exhaust after-treatment technologies, such as selective catalytic reduction and diesel oxidation catalyst, were applied. Real world NOx was reduced by approximately 83%, and THC 77% and CO by 73%, respectively. Real world NOx + THC of the K-tier3 machines exceeded the laboratory emission limit, but the K-tier4 machines considerably improved, 20% for excavator (124 kW), 61% for excavator (90 kW), 90% for wheel loader (202 kW) and 21% for Fork-lift (55 kW), despite some differences. The emission factors applied to the air pollutant inventory have been developed using the engine dynamometer test method, but they were considerably underestimated compared with emissions under real-world working conditions. The difference was even larger for the K-tier4 machines. In this study, the possibility of developing emission factor equations that use the engine load factor as a parameter was confirmed by using the engine work 1 g/kW·h segment moving averaging window (MAW) method.
Open AccessCharacteristics of Real-World Gaseous Emissions from Construction Machinery
In Korea’s air pollutant inventory, construction machinery is a major emission source in the non-road sector. Since 2004, the Korean government has introduced and reinforced emission regulations to reduce the air pollutants emitted from their diesel engines. Since the engine dynamometer test method used in emission regulations has limitations in reflecting emission characteristics under the diverse working conditions of construction machinery, it is necessary to examine the effectiveness of emission regulations and the validity of the emission factors applied as inputs to the air pollutants inventory. This could be done by evaluating engine operation and emission characteristics under real-world working conditions. In this study, 14 units were selected among the excavators, wheel loaders, and forklifts that represent approximately 90% of the registered construction machines in Korea. They were equipped with a portable emission measurement system (PEMS) to measure gaseous emissions and collect engine data under various real-world working conditions. With the reinforcement of emission regulations for the construction machinery from K-tier3 to K-tier4 in Korea, exhaust after-treatment technologies, such as selective catalytic reduction and diesel oxidation catalyst, were applied. Real world NOx was reduced by approximately 83%, and THC 77% and CO by 73%, respectively. Real world NOx + THC of the K-tier3 machines exceeded the laboratory emission limit, but the K-tier4 machines considerably improved, 20% for excavator (124 kW), 61% for excavator (90 kW), 90% for wheel loader (202 kW) and 21% for Fork-lift (55 kW), despite some differences. The emission factors applied to the air pollutant inventory have been developed using the engine dynamometer test method, but they were considerably underestimated compared with emissions under real-world working conditions. The difference was even larger for the K-tier4 machines. In this study, the possibility of developing emission factor equations that use the engine load factor as a parameter was confirmed by using the engine work 1 g/kW·h segment moving averaging window (MAW) method.
- Open Access
- 8 December 2022
- Published by MDPI AG in Preprints.org
Characteristics of Real-world Gaseous Emissions from Construction Machinery
In Korea’s air pollutant inventory, construction machinery is a major emission source in the non-road sector. Since 2004, the Korean government has introduced and reinforced emission regulations to reduce the air pollutants emitted from their diesel engines. Since the engine dynamometer test method used in emission regulations has limitations in reflecting emission characteristics under the diverse working conditions of construction machinery, it is necessary to examine the effectiveness of emission regulations and the validity of the emission factors applied as inputs to the air pollutants inventory. This could be done by evaluating engine operation and emission characteristics under real-world working conditions. In this study, 14 units were selected among the excavators, wheel loaders, and forklifts that represent approximately 90% of the registered construction machines in Korea. They were equipped with a portable emission measurement system (PEMS) to measure gaseous emissions and collect engine data under various real-world working conditions. With the reinforcement of emission regulations for the construction machinery from K-tier3 to K-tier4 in Korea, exhaust after-treatment technologies, such as selective catalytic reduction and diesel oxidation catalyst, were applied. Real world NOx were reduced by approximately 83%, and THC 77% and CO by 73%, respectively. Real world NOx + THC of the K-tier3 machines exceeded the laboratory emission limit, but the K-tier4 machines considerably improved despite some differences. The emission factors applied to the air pollutant inventory have been developed using the engine dynamometer test method, but they were considerably underestimated compared with emissions under real-world working conditions. The difference was even larger for the K-tier4 machines. In this study, the possibility of developing emission factor equations that use the engine load factor as a parameter was confirmed by using the engine work 1 g/kW·h segment moving averaging window (MAW) method.
- 8 December 2022
- Published by MDPI AG in Preprints.org
Open AccessCharacteristics of Real-world Gaseous Emissions from Construction Machinery
In Korea’s air pollutant inventory, construction machinery is a major emission source in the non-road sector. Since 2004, the Korean government has introduced and reinforced emission regulations to reduce the air pollutants emitted from their diesel engines. Since the engine dynamometer test method used in emission regulations has limitations in reflecting emission characteristics under the diverse working conditions of construction machinery, it is necessary to examine the effectiveness of emission regulations and the validity of the emission factors applied as inputs to the air pollutants inventory. This could be done by evaluating engine operation and emission characteristics under real-world working conditions. In this study, 14 units were selected among the excavators, wheel loaders, and forklifts that represent approximately 90% of the registered construction machines in Korea. They were equipped with a portable emission measurement system (PEMS) to measure gaseous emissions and collect engine data under various real-world working conditions. With the reinforcement of emission regulations for the construction machinery from K-tier3 to K-tier4 in Korea, exhaust after-treatment technologies, such as selective catalytic reduction and diesel oxidation catalyst, were applied. Real world NOx were reduced by approximately 83%, and THC 77% and CO by 73%, respectively. Real world NOx + THC of the K-tier3 machines exceeded the laboratory emission limit, but the K-tier4 machines considerably improved despite some differences. The emission factors applied to the air pollutant inventory have been developed using the engine dynamometer test method, but they were considerably underestimated compared with emissions under real-world working conditions. The difference was even larger for the K-tier4 machines. In this study, the possibility of developing emission factor equations that use the engine load factor as a parameter was confirmed by using the engine work 1 g/kW·h segment moving averaging window (MAW) method.
- Open Access
- 1 December 2022
- Published by The Korean Society of Automotive Engineers in Transaction of the Korean Society of Automotive Engineers
- Vol. 30 (12) , 949-954
Study on Evaluation and Improvement of CAPSS Diurnal Loss Emission Formula by Gasoline Vehicle Diurnal Test
- 1 December 2022
- Published by The Korean Society of Automotive Engineers in Transaction of the Korean Society of Automotive Engineers
- Vol. 30 (12) , 949-954
Open AccessStudy on Evaluation and Improvement of CAPSS Diurnal Loss Emission Formula by Gasoline Vehicle Diurnal Test