Taisiya Guseva
Taisiya Guseva has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Alexander A. Saprykin
National Research Tomsk Polytechnic University, Tomsk Russian Federation 634050
2 shared publications - Egor A. Ibragimov
National Research Tomsk Polytechnic University, Tomsk Russian Federation 634050
2 shared publications - Natalia Saprykina
Natl Res Tomsk Polytech Univ, 30 Lenin Ave, Tomsk 634050, Russia
2 shared publications - Valentina V. Chebodaeva
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia
2 shared publications - Yurii P. Sharkeev
Institute of Strength Physics and Materials Science, Siberian Branch of the Russian Academy of Sciences
2 shared publications
Latest Publications
- 15 March 2024
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 26 (1)
Optimization of selective laser melting modes of powder composition of the AlSiMg system
Introduction. New aluminum-based powder systems are currently being developed for additive manufacturing. The scientists' work is aimed at comprehensive studies of powder production, optimization of conditions for alloy production and formation of three-dimensional specimens with minimal porosity and absence of cracking during selective laser melting. The purpose of this work is the synthesis of an almost spherical Al-Si-Mg composite powder (91 wt. % Al, 8 wt. % Si, 1 wt. % Mg) from aluminum powder PA-4 (GOST 6058-22), silicon powder (GOST 2169-69) and magnesium powder MPF-4 (GOST 6001-79), which were not originally intended for selective laser melting technology. The work also provides for the optimization of selective laser melting modes to obtain an alloy and form three-dimensional specimens with minimal porosity and no cracking. To create a powder composition, powders ranging in size from 20 to 64 μm were selected by sieve analysis and subjected to mechanical mixing in a ball mill in a protective argon medium for one hour. The research methods are methods of X-ray diffraction and X-ray phase analysis, transmission electron microscopy, mechanical tests of microhardness. Studies of the powder composition after mechanical mixing showed that the mixed powder of aluminum, silicon and magnesium is a conglomerate of particles of spherical, oval and irregular shape. Results and discussions. The optimal modes for obtaining a specimen with a minimum porosity of 0.03 % and a microhardness of 1,291 MPa are selective laser melting modes: P = 90 W, V = 225 mm/s, S = 0.08 mm, h = 0.025 mm. The conducted research shows the possibility of synthesizing products from metal powders that are not adapted to processing by selective laser melting and obtaining an alloy with new mechanical properties during laser action.
- 15 March 2024
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 26 (1)
Optimization of selective laser melting modes of powder composition of the AlSiMg system
Introduction. New aluminum-based powder systems are currently being developed for additive manufacturing. The scientists' work is aimed at comprehensive studies of powder production, optimization of conditions for alloy production and formation of three-dimensional specimens with minimal porosity and absence of cracking during selective laser melting. The purpose of this work is the synthesis of an almost spherical Al-Si-Mg composite powder (91 wt. % Al, 8 wt. % Si, 1 wt. % Mg) from aluminum powder PA-4 (GOST 6058-22), silicon powder (GOST 2169-69) and magnesium powder MPF-4 (GOST 6001-79), which were not originally intended for selective laser melting technology. The work also provides for the optimization of selective laser melting modes to obtain an alloy and form three-dimensional specimens with minimal porosity and no cracking. To create a powder composition, powders ranging in size from 20 to 64 μm were selected by sieve analysis and subjected to mechanical mixing in a ball mill in a protective argon medium for one hour. The research methods are methods of X-ray diffraction and X-ray phase analysis, transmission electron microscopy, mechanical tests of microhardness. Studies of the powder composition after mechanical mixing showed that the mixed powder of aluminum, silicon and magnesium is a conglomerate of particles of spherical, oval and irregular shape. Results and discussions. The optimal modes for obtaining a specimen with a minimum porosity of 0.03 % and a microhardness of 1,291 MPa are selective laser melting modes: P = 90 W, V = 225 mm/s, S = 0.08 mm, h = 0.025 mm. The conducted research shows the possibility of synthesizing products from metal powders that are not adapted to processing by selective laser melting and obtaining an alloy with new mechanical properties during laser action.
- 15 December 2022
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 24 (4)
Synthesis of a three-component aluminum-based alloy by selective laser melting
Introduction. The technology of selective laser melting is one of the key technologies in Industry 4.0, which allows manufacturing products of any complex geometric shape, reducing significantly the amount of material used, reducing the lead time and obtaining a new alloy from elementary powders in the melting process. To understand the process of alloy formation under laser exposure, it is necessary to know the initial data of powders, which significantly affect the quality of the products obtained. The purpose of this study is to determine the requirements for the structural-phase state, elemental composition of aluminum, silicon and magnesium powders and further preparation of Al-Si-Mg (Al — 91 wt.%, Si — 8 wt.%, Mg — 1 wt.%) powder mixture for laser synthesis. The initial powders of aluminum PA-4 (GOST 6058-73), silicon (GOST 2169-69) and magnesium MPF-4 (GOST 6001-79) and powder composition Al-Si-Mg are studied using X-ray diffraction and X-ray phase analysis. The shape and sizes of particles are determined by the studies of raster electronic images. By the method of selective laser melting, samples are obtained from a powder composition under constant and pulsed laser exposure. The composition is prepared by mixing powders in a globe mill. Results and discussion. It is shown that the initial powders of aluminum, silicon and magnesium are single-phase. Particles with a size of 20–64 µm, recommended for selective laser melting, are used to obtain a powder composition. By mixing the powders for one hour, spherical particles are obtained, which is preferable for laser melting. The results of grinding the samples after laser melting showed that the samples obtained under constant laser exposure at the following mode parameters: P = 80 W, V = 300 mm/s, s = 90 μm, h = 25 μm have the greatest mechanical strength. Conclusions. The described study shows the possibility of synthesizing products from a powder composition of aluminum, silicon and magnesium by selective laser melting.
- 15 December 2022
- Published by Novosibirsk State Technical University in Metal Working and Material Science
- Vol. 24 (4)
Synthesis of a three-component aluminum-based alloy by selective laser melting
Introduction. The technology of selective laser melting is one of the key technologies in Industry 4.0, which allows manufacturing products of any complex geometric shape, reducing significantly the amount of material used, reducing the lead time and obtaining a new alloy from elementary powders in the melting process. To understand the process of alloy formation under laser exposure, it is necessary to know the initial data of powders, which significantly affect the quality of the products obtained. The purpose of this study is to determine the requirements for the structural-phase state, elemental composition of aluminum, silicon and magnesium powders and further preparation of Al-Si-Mg (Al — 91 wt.%, Si — 8 wt.%, Mg — 1 wt.%) powder mixture for laser synthesis. The initial powders of aluminum PA-4 (GOST 6058-73), silicon (GOST 2169-69) and magnesium MPF-4 (GOST 6001-79) and powder composition Al-Si-Mg are studied using X-ray diffraction and X-ray phase analysis. The shape and sizes of particles are determined by the studies of raster electronic images. By the method of selective laser melting, samples are obtained from a powder composition under constant and pulsed laser exposure. The composition is prepared by mixing powders in a globe mill. Results and discussion. It is shown that the initial powders of aluminum, silicon and magnesium are single-phase. Particles with a size of 20–64 µm, recommended for selective laser melting, are used to obtain a powder composition. By mixing the powders for one hour, spherical particles are obtained, which is preferable for laser melting. The results of grinding the samples after laser melting showed that the samples obtained under constant laser exposure at the following mode parameters: P = 80 W, V = 300 mm/s, s = 90 μm, h = 25 μm have the greatest mechanical strength. Conclusions. The described study shows the possibility of synthesizing products from a powder composition of aluminum, silicon and magnesium by selective laser melting.