Huimin Chang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Huimin Chang has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Yan Zhao
School of Environment, Beijing Normal University, Beijing 100875, China
5 shared publications Anders Damgaard
Department of Environmental and Resource Engineering, Technical University of Denmark, Kongens Lyngby 2800, Denmark
3 shared publicationsAnkun Xu
School of Environment, Beijing Normal University, Beijing, China
2 shared publicationsThomas H Christensen
Department of Environmental Engineering, Technical University of Denmark, Kongens Lyngby, Denmark
2 shared publicationsXiang Li
2 shared publicationsChangqing Xu
School of Economics, Beijing Institute of Technology, Beijing, 100081, China; Digital Economy and Policy Intelligentization Key Laboratory of Ministry of Industry and Information Technology, Beijing, 100081, China
1 shared publication
Latest Publications
- 25 February 2025
- Published by Elsevier in Journal of Environmental Management
- Vol. 377, 124644
Emission factors and driving forces of provincial-level CO2 from electricity production and consumption in China from 2013 to 2020
- 25 February 2025
- Published by Elsevier in Journal of Environmental Management
- Vol. 377, 124644
Emission factors and driving forces of provincial-level CO2 from electricity production and consumption in China from 2013 to 2020
- 18 March 2024
- Published by Elsevier in Biomass and Bioenergy
- Vol. 183
Life cycle environmental impacts of five technological routes for straw utilisation in China
- 18 March 2024
- Published by Elsevier in Biomass and Bioenergy
- Vol. 183
Life cycle environmental impacts of five technological routes for straw utilisation in China
- 18 November 2023
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 200
Green steel: The future path towards sustainable automotive manufacturing
- 18 November 2023
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 200
Green steel: The future path towards sustainable automotive manufacturing
- 21 May 2023
- Published by Elsevier in Water Research
- Vol. 240, 120109
Climate change impacts of conventional sewage sludge treatment and disposal
- 21 May 2023
- Published by Elsevier in Water Research
- Vol. 240, 120109
Climate change impacts of conventional sewage sludge treatment and disposal
- Open Access
- 12 January 2023
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 41 (6) , 1081-1088
Mini-review of inventory data for the dewatering and drying of sewage sludge
Technological comparison and system modelling of sewage sludge treatment are important in terms of sustainable development and climate change mitigation. Dewatering and drying are important processes for reducing volume for transportation and often a requirement for further sludge treatment. Inventory data on mass transfers and material and energy consumptions are therefore crucial in improving and understanding sludge management systems. Reviewing the scientific literature (2003–2021) revealed 55 and 21 datasets on dewatering and drying of sewage sludge, respectively. The scarcity of data did not allow for identifying detailed relationships between inputs and outputs for the technologies, but the reviewed data can serve as the first port of call when planning sludge management. The average total solid (TS) content obtained was statistically different for mechanical dewatering (MDW), deep dewatering, bio-drying (BDR) and thermal drying (TDR). Loss of volatile solids (VS) during dewatering is barely described, but a substantial VS loss was observed for TDR (8%) and BDR (27%). The use of chemical agents in MDW showed typical values of 5–15 g kg−1 TS. The use of energy is low for MDW (average of 0.12 and 0.26 kWh kg−1 TS for raw and digested sludges, respectively) but substantially higher for TDR (average of 3.8 kWh kg−1 TS). The justified inventory data for sludge dewatering and drying provide essential support to system modelling and technological comparison in future studies, but additional data from full-scale plants on energy consumption and the composition of removed water are strongly requested to improve the inventory.
- 12 January 2023
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 41 (6) , 1081-1088
Open AccessMini-review of inventory data for the dewatering and drying of sewage sludge
Technological comparison and system modelling of sewage sludge treatment are important in terms of sustainable development and climate change mitigation. Dewatering and drying are important processes for reducing volume for transportation and often a requirement for further sludge treatment. Inventory data on mass transfers and material and energy consumptions are therefore crucial in improving and understanding sludge management systems. Reviewing the scientific literature (2003–2021) revealed 55 and 21 datasets on dewatering and drying of sewage sludge, respectively. The scarcity of data did not allow for identifying detailed relationships between inputs and outputs for the technologies, but the reviewed data can serve as the first port of call when planning sludge management. The average total solid (TS) content obtained was statistically different for mechanical dewatering (MDW), deep dewatering, bio-drying (BDR) and thermal drying (TDR). Loss of volatile solids (VS) during dewatering is barely described, but a substantial VS loss was observed for TDR (8%) and BDR (27%). The use of chemical agents in MDW showed typical values of 5–15 g kg−1 TS. The use of energy is low for MDW (average of 0.12 and 0.26 kWh kg−1 TS for raw and digested sludges, respectively) but substantially higher for TDR (average of 3.8 kWh kg−1 TS). The justified inventory data for sludge dewatering and drying provide essential support to system modelling and technological comparison in future studies, but additional data from full-scale plants on energy consumption and the composition of removed water are strongly requested to improve the inventory.
- Open Access
- 9 December 2022
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 41 (5) , 970-976
Mini-review of sewage sludge parameters related to system modelling
System modelling of sewage sludge (SS) treatment attracts a growing interest for better comparison and optimisation of technologies. However, SS parameters need to be generalised to be used in holistic assessments, since scattered data may inhibit the development and interpretation of system models. A review of the literature on SS parameters relevant to modelling SS treatment systems revealed 208 datasets published in 162 publicly available scientific papers. We treated thickened and dewatered sludge in the same data analysis, but in some cases, this was an incorrect assumption. The compositional data showed significant variations, but most of the data subscribed to a lognormal distribution, albeit with varying levels of significance. On average, the thickened sludge contained 3.3 ± 1.7% total solid (TS), and the dewatered sludge contained 21.0 ± 6.7% TS. For the combined data, the average Ash content was 32.4 ± 11.8% of TS. Other characteristic parameters were the lower heating value (LHV) of 22.1 ± 2.1 MJ kg−1 volatile solid (VS) and the biochemical methane potential (BMP) of 0.25 ± 0.11 m3 CH4 kg−1 VS. Fertiliser-related elements were on average 53.3 ± 9.3% C in VS, 6.8 ± 2.2% N in VS, 6.7 ± 2.4% P in Ash and 1.7 ± 1.3% K in Ash. The data reviewed herein provide a good basis for assessing the generality of individual SS data and for selecting key parameters for modelling SS treatment systems. However, the review reveals a need for the better characterisation of SS in the future.
- 9 December 2022
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 41 (5) , 970-976
Open AccessMini-review of sewage sludge parameters related to system modelling
System modelling of sewage sludge (SS) treatment attracts a growing interest for better comparison and optimisation of technologies. However, SS parameters need to be generalised to be used in holistic assessments, since scattered data may inhibit the development and interpretation of system models. A review of the literature on SS parameters relevant to modelling SS treatment systems revealed 208 datasets published in 162 publicly available scientific papers. We treated thickened and dewatered sludge in the same data analysis, but in some cases, this was an incorrect assumption. The compositional data showed significant variations, but most of the data subscribed to a lognormal distribution, albeit with varying levels of significance. On average, the thickened sludge contained 3.3 ± 1.7% total solid (TS), and the dewatered sludge contained 21.0 ± 6.7% TS. For the combined data, the average Ash content was 32.4 ± 11.8% of TS. Other characteristic parameters were the lower heating value (LHV) of 22.1 ± 2.1 MJ kg−1 volatile solid (VS) and the biochemical methane potential (BMP) of 0.25 ± 0.11 m3 CH4 kg−1 VS. Fertiliser-related elements were on average 53.3 ± 9.3% C in VS, 6.8 ± 2.2% N in VS, 6.7 ± 2.4% P in Ash and 1.7 ± 1.3% K in Ash. The data reviewed herein provide a good basis for assessing the generality of individual SS data and for selecting key parameters for modelling SS treatment systems. However, the review reveals a need for the better characterisation of SS in the future.