Xing Zou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xing Zou has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Botao Xie
CNOOC Research Institute Co., Ltd., Beijing 100028, China
4 shared publications - Zhipeng Zang
Tianjin University
4 shared publications - Enbang Chen
State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin University, Tianjin 300350, China
1 shared publication - Fan Zhang
State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin University, Tianjin 300350, China
1 shared publication - Jinfeng Zhang
State Key Laboratory of Hydraulic Engineering Intelligent Construction and Operation, Tianjin University, Tianjin, China
1 shared publication - Jing Hou
Engineering Research & Design Department, CNOOC Research Institute, Beijing 100027, China
1 shared publication
Latest Publications
- Open Access
- 8 January 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (1) , 107
Investigations on Free Span Rectification for a Submarine Pipeline on Sand Wave Seabeds
Sand waves are large-scale bed forms commonly occurring on the continental shelf seabed and can result in free spans of submarine pipelines, which may have an influence on the stability of the pipelines. Existing span rectification procedures have primarily focused on local rectification methods for free spans caused by local scour or individual spans resulting from seabed unevenness. This paper aims to present a span rectification design applicable to the pipeline crossing sand wave region, and to offer practical guidance on sand wave intervention strategies. A large-scale approach is necessary for the rectification of multiple spans across the field, which may involve the use of either a mass flow excavator (MFE) or a remotely operated vehicle (ROV) jetting tool. A comparative analysis of the estimated durations for post-lay trenching using the MFE and ROV jetting tools is also provided. In instances where the large-scale method fails to achieve span lengths suitable for long-term operation, a localized approach is necessary to address individual spans. The desired trench depth can be attained through a combination of pre-lay and/or post-lay trenching techniques. The analysis of on-bottom roughness and free span has demonstrated that, given the natural seabed profile without trenching, there are no spans surpassing the ultimate limit state (ULS) or fatigue limit state (FLS) criteria for the temporary installation scenario. Consequently, pre-lay rectification is not necessary. However, the analysis indicates that post-lay rectification is essential to meet ULS and FLS criteria under operating conditions. All spans that exceed the ULS and FLS criteria can be effectively rectified by trenching to a depth of 1 m.
- 8 January 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (1) , 107
Open AccessInvestigations on Free Span Rectification for a Submarine Pipeline on Sand Wave Seabeds
Sand waves are large-scale bed forms commonly occurring on the continental shelf seabed and can result in free spans of submarine pipelines, which may have an influence on the stability of the pipelines. Existing span rectification procedures have primarily focused on local rectification methods for free spans caused by local scour or individual spans resulting from seabed unevenness. This paper aims to present a span rectification design applicable to the pipeline crossing sand wave region, and to offer practical guidance on sand wave intervention strategies. A large-scale approach is necessary for the rectification of multiple spans across the field, which may involve the use of either a mass flow excavator (MFE) or a remotely operated vehicle (ROV) jetting tool. A comparative analysis of the estimated durations for post-lay trenching using the MFE and ROV jetting tools is also provided. In instances where the large-scale method fails to achieve span lengths suitable for long-term operation, a localized approach is necessary to address individual spans. The desired trench depth can be attained through a combination of pre-lay and/or post-lay trenching techniques. The analysis of on-bottom roughness and free span has demonstrated that, given the natural seabed profile without trenching, there are no spans surpassing the ultimate limit state (ULS) or fatigue limit state (FLS) criteria for the temporary installation scenario. Consequently, pre-lay rectification is not necessary. However, the analysis indicates that post-lay rectification is essential to meet ULS and FLS criteria under operating conditions. All spans that exceed the ULS and FLS criteria can be effectively rectified by trenching to a depth of 1 m.
- Open Access
- 23 October 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (10) , 2031
Vortex-Induced Vibration and Fatigue Damage Assessment for a Submarine Pipeline on a Sand Wave Seabed
Sand waves are commonly formed on the sandy seabed of the continental shelf and characterized by their regular wave-like shape. When a submarine pipeline is laid on this type of seabed, it often experiences free spans due to the unevenness of the seabed. These free spans are particularly vulnerable to vortex-induced vibration (VIV) and the resulting fatigue damage, which have been identified as the primary causes of pipeline failures in offshore oil and gas exploration. This study examines the VIV and fatigue damage of free spans in a submarine pipeline in the Lufeng oilfield, which is located in a large area of sand waves. The assessment conditions encompass the as-laid empty state, the flooded state, and the operational state. Additionally, both the minimum and maximum lay tension are taken into account during the evaluation of VIV and fatigue. The VIV onset screening conducted revealed a considerable number of pipeline free spans exceeding the VIV onset span lengths under both temporary and operating conditions for the non-trench seabed. Furthermore, the analyses indicate that the pipeline does not meet the criteria for VIV fatigue on a non-trenched seabed. Consequently, a proposed solution of implementing a 1 m trench rectification measure for the seabed is recommended. The results demonstrate that this measure effectively mitigates the occurrence of VIV and subsequently reduces fatigue damage across all conditions.
- 23 October 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (10) , 2031
Open AccessVortex-Induced Vibration and Fatigue Damage Assessment for a Submarine Pipeline on a Sand Wave Seabed
Sand waves are commonly formed on the sandy seabed of the continental shelf and characterized by their regular wave-like shape. When a submarine pipeline is laid on this type of seabed, it often experiences free spans due to the unevenness of the seabed. These free spans are particularly vulnerable to vortex-induced vibration (VIV) and the resulting fatigue damage, which have been identified as the primary causes of pipeline failures in offshore oil and gas exploration. This study examines the VIV and fatigue damage of free spans in a submarine pipeline in the Lufeng oilfield, which is located in a large area of sand waves. The assessment conditions encompass the as-laid empty state, the flooded state, and the operational state. Additionally, both the minimum and maximum lay tension are taken into account during the evaluation of VIV and fatigue. The VIV onset screening conducted revealed a considerable number of pipeline free spans exceeding the VIV onset span lengths under both temporary and operating conditions for the non-trench seabed. Furthermore, the analyses indicate that the pipeline does not meet the criteria for VIV fatigue on a non-trenched seabed. Consequently, a proposed solution of implementing a 1 m trench rectification measure for the seabed is recommended. The results demonstrate that this measure effectively mitigates the occurrence of VIV and subsequently reduces fatigue damage across all conditions.
- Open Access
- 27 February 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (3) , 517
A Numerical Simulation of Internal Wave Propagation on a Continental Slope and Its Influence on Sediment Transport
Significant current velocity near the sea bottom can be induced by internal waves, even for water a few hundred meters in depth. In this study, a nonhydrostatic ocean model was applied to simulate the generation and propagation of internal waves on the continental slope of the northern SCS. Based on the analyses of the vertical profiles of the currents, the propagation of internal waves along the continental slope can be categorized into six modes. The bed shear stress and the bedload transport were calculated to analyze the general characteristics of sediment transport along the continental slope of the northern SCS. Generally, there was no sediment transport on the sea bottom induced by the internal waves when the water depth was deeper than 650 m or shallower than 80 m. The downslope sediment transport dominated the slope at a water depth range of 200~650 m, while the upslope sediment transport dominated the slope at a water depth range of 80~200 m. The predicted directions of the bedload transport are coincident with the field observations of sand wave migration on the continental slope, which further confirms that the main cause of the generation and formation of sand waves on the continental slope of the northern SCS is the strong bottom current induced by the shoaling process of internal waves.
- 27 February 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (3) , 517
Open AccessA Numerical Simulation of Internal Wave Propagation on a Continental Slope and Its Influence on Sediment Transport
Significant current velocity near the sea bottom can be induced by internal waves, even for water a few hundred meters in depth. In this study, a nonhydrostatic ocean model was applied to simulate the generation and propagation of internal waves on the continental slope of the northern SCS. Based on the analyses of the vertical profiles of the currents, the propagation of internal waves along the continental slope can be categorized into six modes. The bed shear stress and the bedload transport were calculated to analyze the general characteristics of sediment transport along the continental slope of the northern SCS. Generally, there was no sediment transport on the sea bottom induced by the internal waves when the water depth was deeper than 650 m or shallower than 80 m. The downslope sediment transport dominated the slope at a water depth range of 200~650 m, while the upslope sediment transport dominated the slope at a water depth range of 80~200 m. The predicted directions of the bedload transport are coincident with the field observations of sand wave migration on the continental slope, which further confirms that the main cause of the generation and formation of sand waves on the continental slope of the northern SCS is the strong bottom current induced by the shoaling process of internal waves.
- Open Access
- 17 December 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (12) , 2019
Numerical Investigations on Scour and Flow around Two Crossing Pipelines on a Sandy Seabed
When a pipeline is laid on the seabed, local scour often occurs below it due to sea currents. In practical engineering, there are some cases that two pipelines laid on the seabed need to cross with each other. The complex flow structures around two crossing pipelines make the scour characteristics different from that of an isolated single pipeline. In this study, scour below two crossing pipelines was simulated numerically using the CFD software Flow-3D. The study is focused on the effect of the intersecting angle on the equilibrium depth and time scale of scour below the crossing position. Five intersecting angles, i.e., α = 0°, 15°, 30°, 45° and 90°, are considered, where α = 0° and 90° represent two pipelines parallel and perpendicular to each other, respectively. The results show that the equilibrium depth and the time scale of scour below the two crossing pipelines are greater than those of an isolated single pipeline. The equilibrium depth and time scale of scour have the largest values at α = 0° and decrease with the increase of the intersecting angle. Finally, the flow structures around the crossing pipelines are presented to explain the scour process.
- 17 December 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (12) , 2019
Open AccessNumerical Investigations on Scour and Flow around Two Crossing Pipelines on a Sandy Seabed
When a pipeline is laid on the seabed, local scour often occurs below it due to sea currents. In practical engineering, there are some cases that two pipelines laid on the seabed need to cross with each other. The complex flow structures around two crossing pipelines make the scour characteristics different from that of an isolated single pipeline. In this study, scour below two crossing pipelines was simulated numerically using the CFD software Flow-3D. The study is focused on the effect of the intersecting angle on the equilibrium depth and time scale of scour below the crossing position. Five intersecting angles, i.e., α = 0°, 15°, 30°, 45° and 90°, are considered, where α = 0° and 90° represent two pipelines parallel and perpendicular to each other, respectively. The results show that the equilibrium depth and the time scale of scour below the two crossing pipelines are greater than those of an isolated single pipeline. The equilibrium depth and time scale of scour have the largest values at α = 0° and decrease with the increase of the intersecting angle. Finally, the flow structures around the crossing pipelines are presented to explain the scour process.