LLLi Liu

Li Liu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Li Liu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:

  • Xin Guo

    Engineering Research Center of High-Performance Polymer and Molding Technology, Ministry of Education, Qingdao University of Science and Technology, Qingdao 266042, China

    2 shared publications
  • Baogang Zhang

    Institute of High Performance Polymer, Qingdao University of Science & Technology, Qingdao 266042, China

    1 shared publication
  • Guangye Liu

    Engineering Research Center of High-Performance Polymer and Molding Technology, Ministry of Education, Qingdao University of Science and Technology, Qingdao 266042, China

    1 shared publication
  • Le Kang

    Engineering Research Center for High Performance Polymer and Molding Technology, Ministry of Education, Qingdao University of Science & Technology, Qingdao 266042, China

    1 shared publication
  • Mei Shen

    Key Laboratory of Rubber-Plastics, Ministry of Education, School of Polymer Science and Engineering, Qingdao University of Science and Technology, Qingdao 266042, China

    1 shared publication
  • Naixiu Ding

    Engineering Research Center of High Performance Polymer and Molding Technology, Ministry of Education, College of Polymer Science and Engineering, Qingdao University of Science and Technology, Qingdao, China

    1 shared publication

Latest Publications

  • Open Access

    Enhanced Thermal Conductivity of High-Density Polyethylene Composites with Hybrid Fillers of Flaky and Spherical Boron Nitride Particles

    by Zhenliang Gao, Yiding Wang, Baogang Zhang, Li Liu, Xianhu Liu

    The synergistic effect between different fillers plays a crucial role in determining the performance of composites. In this work, spherical boron nitride (BN) and flaky BN are used as hybrid fillers to improve the thermal conductivity (TC) of high-density polyethylene (HDPE) composites. A series of HDPE composites were prepared by adjusting the mass ratio (1:0, 4:1, 2:1, 1:1, 1:2, 1:4, and 0:1) of spherical BN and flaky BN. The SEM results indicate that the spherical BN (with a particle size of 3 μm) effectively filled the gaps between the flaky BN (with a particle size of 30 μm), leading to the formation of more continuous heat conduction paths with the composite. Remarkably, when the mass ratio of spherical BN to flaky BN was set to 1:4 (with a total BN filling amount of 30 wt%), the TC of the composite could reach up to 1.648 Wm−1K−1, which is obviously higher than that of the composite containing a single filler, realizing the synergistic effect of the hybrid fillers. In addition, the synergistic effect of fillers also affects the thermal stability and crystallization behavior of composites. This work is of great significance for optimizing the application of hybrid BN fillers in the field of thermal management.


  • Open Access

    Transformation from Electromagnetic Inflection to Absorption of Silicone Rubber and Accordion-Shaped Ti3C2MXene Composites by Highly Electric Conductive Multi-Walled Carbon Nanotubes

    by Xin Guo, Li Liu, Naixiu Ding, Guangye Liu

    Electromagnetic (EM) pollution becomes more penetrating in daily life and work due to more convenience provided by multi-electrical devices, as does secondary pollution caused by electromagnetic reflection. EM wave absorption material with less reflection is a good solution to absorb unavoidable EM radiation or reduce it from the source. Filled with two-dimensional Ti3SiC2MXenes, silicone rubber (SR)composite demonstrated a good electromagnetic shielding effectiveness of 20 dB in the X band by melt-mixing processes for good conductivity of more than 10−3 S/cm and displayed dielectric properties and a low magnetic permeability; however, the reflection loss was only −4 dB. By the combination of one-dimensional highly electric conductive multi-walled carbon nanotubes (HEMWCNTs) and MXenes, the composites achieved the transformation from electromagnetic inflection to an excellent absorbing performance to reach a minimum reflection loss of −30.19 dB due to electric conductivity of above 10−4 S/cm, a higher dielectric constant, and more loss in both dielectric and magnetic properties. Ni-added multi-walled carbon nanotubes were not able to achieve the transformation. The as-prepared SR/HEMWCNT/MXene composites have potential application prospects in protective layers, which can be used for electromagnetic wave absorption, electromagnetic interference suppression of devices, and stealth of the equipment.


  • Open Access

    Highly Strong Interface Adhesion of Polyester Fiber Rubber Composite via Fiber Surface Modification by Meta-Cresol/Formaldehyde Latex Dipping Emulsion

    by Xiangze Meng, Le Kang, Xin Guo, Xiaohao Tang, Li Liu, Mei Shen

    As a skeleton material, polyester (PET) fiber can significantly improve the strength and durability of rubber composites, but the interfacial adhesion between polyester fiber and rubber is poor due to the chemical inertia of PET fiber surface. Resorcinol-formaldehyde-latex (RFL) impregnating solution is usually used to treat PET fibers, but RFL contains toxic components such as resorcinol, which is harmful to the human body. A simple and less toxic resin-impregnating system cresol-formaldehyde-latex (CFL) was obtained by alternating resorcinol with low-toxicity cresol and m-cresol formaldehyde resin was synthesized from m-cresol and formaldehyde. CFL (m-cresol formaldehyde resin latex) systems with different C/F mole ratios and CF resin/latex ratios were adopted to modify the surface of PET fibers. The strip peeling adhesive and the H pull-out test results indicated that the PET fiber/rubber adhesion strength increased with the increase in the formaldehyde dosage and the CF resin content, and the peeling force value and the H-pull-out force of treated PET/rubber composites reached 7.3 N/piece and 56.8 N, respectively. The optimal choice of CFL adhesive system was obtained, when the C/F mole ratio was 1/2 and the CF resin/latex weight ratio was 0.23. This environment-friendly CFL dipping emulsion can be used as a new surface modification strategy as it can remarkably enhance the interfacial adhesion of PET/rubber composites.