Wei Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wei Yu has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
Yu Bai
7 shared publicationsKaixi Jiang
6 shared publicationsYong Li
State Key Laboratory of Rolling and Automation Northeastern University Shenyang China
6 shared publicationsGuangming Xu
5 shared publicationsHai Hao
5 shared publicationsYishan Wang
5 shared publications
Latest Publications
- Open Access
- 12 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (8) , e202502468
Mechanical and Electromagnetic Interference Shielding Properties of Structurally Reinforced Aluminum Foam
The rapid development of wireless communication technologies has intensified the demand for electromagnetic interference (EMI) shielding materials that simultaneously deliver high shielding effectiveness, robust mechanical performance, and low density. Here, guided by heterointerface engineering and structural reinforcement, fabricates bi‐continuous interpenetrating porous composite structures (BIPCs) by integrating ZL111 alloy lattice struts with an aluminum foam (AF). Three reinforcement architectures are designed: a cubic‐symmetric framework with unidirectional struts (Structure A), a lateral reinforcement (Structure B), and a longitudinal reinforcement (Structure C). Compared with AF, all BIPCs exhibit pronounced improvements in both compressive properties and EMI shielding. Among them, Structure C shows the largest mechanical enhancement, with compressive strength, specific strength, plateau stress, and elastic modulus increased to 2.06, 1.62, 1.42, and 2.25 times those of AF, respectively, while the total shielding effectiveness (SET) increases by 6.6%. The enhanced mechanical response is attributed to the cooperative load transfer provided by the alloy struts and metallurgical bonding in heterointerfaces. Meanwhile, EMI shielding was collaboratively enhanced by reflection loss improvement from the higher electrical conductivity and polarization losses evoked by lattice distortions. This work can not only provide idea for solving the problem of synergistic enhancement of mechanical and EMI shielding properties of AF, but also give a reference for subsequent research to enhance the EMI shielding properties of BIPCs.
- 12 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (8) , e202502468
Open AccessMechanical and Electromagnetic Interference Shielding Properties of Structurally Reinforced Aluminum Foam
The rapid development of wireless communication technologies has intensified the demand for electromagnetic interference (EMI) shielding materials that simultaneously deliver high shielding effectiveness, robust mechanical performance, and low density. Here, guided by heterointerface engineering and structural reinforcement, fabricates bi‐continuous interpenetrating porous composite structures (BIPCs) by integrating ZL111 alloy lattice struts with an aluminum foam (AF). Three reinforcement architectures are designed: a cubic‐symmetric framework with unidirectional struts (Structure A), a lateral reinforcement (Structure B), and a longitudinal reinforcement (Structure C). Compared with AF, all BIPCs exhibit pronounced improvements in both compressive properties and EMI shielding. Among them, Structure C shows the largest mechanical enhancement, with compressive strength, specific strength, plateau stress, and elastic modulus increased to 2.06, 1.62, 1.42, and 2.25 times those of AF, respectively, while the total shielding effectiveness (SET) increases by 6.6%. The enhanced mechanical response is attributed to the cooperative load transfer provided by the alloy struts and metallurgical bonding in heterointerfaces. Meanwhile, EMI shielding was collaboratively enhanced by reflection loss improvement from the higher electrical conductivity and polarization losses evoked by lattice distortions. This work can not only provide idea for solving the problem of synergistic enhancement of mechanical and EMI shielding properties of AF, but also give a reference for subsequent research to enhance the EMI shielding properties of BIPCs.
- Open Access
- 6 March 2026
- Published by Wiley in Advanced Science
- Vol. 13 (25) , e22466
Cluster‐Mediated Solute Stabilization and Shear‐Bypass Synergistic Strengthening in High‐Alloyed Systems
High alloy content and multiphase synergistic strengthening have become crucial strategies in contemporary metallic materials design for performance enhancement. A major challenge in this field lies in addressing compositional segregation arising from differences in solute diffusion, especially in high‐alloy systems such as aluminum‐lithium (Al‐Li) alloys. This study explores the 2060 Al‐Li alloy, a representative high‐alloy system, produced using twin‐roll casting, a segregation‐sensitive process, and analyzes segregation behavior through a customized solute field model. The results reveal that nanoclusters with high solute tolerance effectively reduce segregation‐induced degradation, leading to significant improvements in both strength and ductility, with an 18.7% increase in strength and a 41.5% increase in elongation. Furthermore, a shear‐bypass synergistic strengthening mechanism was identified. This work not only unlocks the potential of the twin‐roll casting process by leveraging sub‐rapid solidification advantages but also offers a promising technical and theoretical approach to mitigating compositional segregation, addressing a long‐standing challenge within the high‐alloy metallic materials industry.
- 6 March 2026
- Published by Wiley in Advanced Science
- Vol. 13 (25) , e22466
Open AccessCluster‐Mediated Solute Stabilization and Shear‐Bypass Synergistic Strengthening in High‐Alloyed Systems
High alloy content and multiphase synergistic strengthening have become crucial strategies in contemporary metallic materials design for performance enhancement. A major challenge in this field lies in addressing compositional segregation arising from differences in solute diffusion, especially in high‐alloy systems such as aluminum‐lithium (Al‐Li) alloys. This study explores the 2060 Al‐Li alloy, a representative high‐alloy system, produced using twin‐roll casting, a segregation‐sensitive process, and analyzes segregation behavior through a customized solute field model. The results reveal that nanoclusters with high solute tolerance effectively reduce segregation‐induced degradation, leading to significant improvements in both strength and ductility, with an 18.7% increase in strength and a 41.5% increase in elongation. Furthermore, a shear‐bypass synergistic strengthening mechanism was identified. This work not only unlocks the potential of the twin‐roll casting process by leveraging sub‐rapid solidification advantages but also offers a promising technical and theoretical approach to mitigating compositional segregation, addressing a long‐standing challenge within the high‐alloy metallic materials industry.
- 9 February 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1057
Synergistic control of α-Al grain refinement and eutectic Si modification enabled by the novel Al-5La-1B inoculant
- 9 February 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1057
Synergistic control of α-Al grain refinement and eutectic Si modification enabled by the novel Al-5La-1B inoculant
- Open Access
- 3 February 2026
- Published by Elsevier in Materials & Design
- Vol. 263
Strength-ductility synergy and multiscale particle-solute interaction mechanisms in Al-Cu composites reinforced by TiC/TiB2 nanoparticles
- 3 February 2026
- Published by Elsevier in Materials & Design
- Vol. 263
Open AccessStrength-ductility synergy and multiscale particle-solute interaction mechanisms in Al-Cu composites reinforced by TiC/TiB2 nanoparticles
- 1 November 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1046
Synergistic improvement of strength and plasticity of HPDC Al-7Si-Mg-Cu alloy with submicron-nanometer multi-scale particles
- 1 November 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1046
Synergistic improvement of strength and plasticity of HPDC Al-7Si-Mg-Cu alloy with submicron-nanometer multi-scale particles
- Open Access
Effects of Fe and Zn Additions on Microstructure and Mechanical Properties of Al–10Si–Mg Alloy
Based on the idea of integrated computational materials Engineering (ICME), this research applies a digital integrated computing platform integrating ProCAST and MATLAB software. The effects of Fe and Zn contents on the microstructure and properties of die-casting Al–10Si–Mg alloy was investigated through numerical simulation and experimental characterization. The results show that with Fe and Zn contents of 1.30 and 0.25 wt.%, respectively, the grain size and porosity of the die-cast parts are the smallest, and the yield strength and tensile strength are 203 MPa and 313 MPa, respectively. Compared with the addition of 0.14 wt.% Fe and 0.01 wt.% Zn, the increase was 16% and 15.5%, respectively. When the Fe content is higher than 1.30 wt.%, the size of the β-Al5FeSi phase in the alloy matrix increases. Moreover, as the Fe content increases, the morphology of the β-Al5FeSi transforms from elongated to a needle-like shape, which increases brittleness and reduces elongation, tensile strength, and yield strength. When 0.25 wt.% Zn is added, the segregation phenomenon of eutectic Si in the Al–10Si–Mg alloy is inhibited and the tensile strength and yield strength are improved. However, with the increase in Zn content to 0.95 wt.%, there is the coarsening of eutectic Si, resulting in a decreased elongation and decreased mechanical properties. The optimization method of the integrated computing platform greatly simplifies the computing cycle and improves work efficiency.
Open AccessEffects of Fe and Zn Additions on Microstructure and Mechanical Properties of Al–10Si–Mg Alloy
Based on the idea of integrated computational materials Engineering (ICME), this research applies a digital integrated computing platform integrating ProCAST and MATLAB software. The effects of Fe and Zn contents on the microstructure and properties of die-casting Al–10Si–Mg alloy was investigated through numerical simulation and experimental characterization. The results show that with Fe and Zn contents of 1.30 and 0.25 wt.%, respectively, the grain size and porosity of the die-cast parts are the smallest, and the yield strength and tensile strength are 203 MPa and 313 MPa, respectively. Compared with the addition of 0.14 wt.% Fe and 0.01 wt.% Zn, the increase was 16% and 15.5%, respectively. When the Fe content is higher than 1.30 wt.%, the size of the β-Al5FeSi phase in the alloy matrix increases. Moreover, as the Fe content increases, the morphology of the β-Al5FeSi transforms from elongated to a needle-like shape, which increases brittleness and reduces elongation, tensile strength, and yield strength. When 0.25 wt.% Zn is added, the segregation phenomenon of eutectic Si in the Al–10Si–Mg alloy is inhibited and the tensile strength and yield strength are improved. However, with the increase in Zn content to 0.95 wt.%, there is the coarsening of eutectic Si, resulting in a decreased elongation and decreased mechanical properties. The optimization method of the integrated computing platform greatly simplifies the computing cycle and improves work efficiency.
- 4 March 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 897
The effect of asymmetric rolling on the microstructure and properties of Al–Cu–Li–TiC/TiB2 alloys
- 4 March 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 897
The effect of asymmetric rolling on the microstructure and properties of Al–Cu–Li–TiC/TiB2 alloys