Haibing Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Haibing Li has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Linyu Yang
Xinjiang Key Laboratory of Solid State Physics and Devices, Xinjiang University, Urumqi 830046, China
3 shared publications Fumin Zhang
State Key Laboratory of Precision Measurement Technology and Instruments, Tianjin University, Tianjin 300072, P.R. China
2 shared publications- Feng Li
Xinjiang Uygur Autonomous Region Research Institute of Measurement and Testing, Urumqi, China
1 shared publication Hongyu Mi
School of Chemical Engineering and Technology, Xinjiang University, Urumqi 830046, China
1 shared publicationJiadong Wu
School of Physics and Technology, Xin Jiang University, Urumqi, Xinjiang 830046, P.R. China
1 shared publicationLiyun Zhu
College of Modern Science and Technology, China Jiliang University, Jinhua 322000, P.R. China
1 shared publication
Latest Publications
- 6 December 2024
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (2) , 191-201
K + -regulated vanadium oxide heterostructure enables high-performance aqueous zinc-ion batteries
Novel triple-phase K 2 V 3 O 8 , K 3 V 8 O 21 and VO 2 heterostructures were synthesized using a solid reaction procedure for zinc-ion batteries.
- 6 December 2024
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 27 (2) , 191-201
K + -regulated vanadium oxide heterostructure enables high-performance aqueous zinc-ion batteries
Novel triple-phase K 2 V 3 O 8 , K 3 V 8 O 21 and VO 2 heterostructures were synthesized using a solid reaction procedure for zinc-ion batteries.
- 7 March 2024
- Published by Springer Nature in Ionics
- Vol. 30 (5) , 2697-2704
In-situ sintering induced VO2/V2O5 heterostructure as cathode for high-capacity reversible aqueous Zn-ion batteries
- 7 March 2024
- Published by Springer Nature in Ionics
- Vol. 30 (5) , 2697-2704
In-situ sintering induced VO2/V2O5 heterostructure as cathode for high-capacity reversible aqueous Zn-ion batteries
- Open Access
Development and Characterizations of Novel Aqueous-Based Ceramic Inks for Inkjet Printing
Stable rheological properties of ceramic ink are a key requirement for inkjet printing (IJP), which should be satisfied in terms of the Reynolds and Weber numbers. In this paper, the reverse microemulsion was introduced for the synthesis of monodispersed nanosized ceramic powders, and the average size was less than 100 nm. A comparison of two different dispersants, i.e., polyacrylic ammonium (PAANH4) and polyacrylic aid (PAA), revealed that the former exerted a good dispersion effect on the ceramic ink. The sedimentation ratio, zeta potential, surface tension, viscosity, and density of the inks were measured, and the Reynolds and Weber numbers, as well as Z value, were calculated. A stable, homogeneous, and high solid loading (20 wt%) ceramic ink could be achieved after aging for a period of 72 h. Finally, the ceramic inks showed the desired printable property in the inkjet printing process. Combining inkjet printing technology with a sintering process, Ni-Mn-O films have the potential to monitor temperature and humidity parameters for intelligent wearable devices.
Open AccessDevelopment and Characterizations of Novel Aqueous-Based Ceramic Inks for Inkjet Printing
Stable rheological properties of ceramic ink are a key requirement for inkjet printing (IJP), which should be satisfied in terms of the Reynolds and Weber numbers. In this paper, the reverse microemulsion was introduced for the synthesis of monodispersed nanosized ceramic powders, and the average size was less than 100 nm. A comparison of two different dispersants, i.e., polyacrylic ammonium (PAANH4) and polyacrylic aid (PAA), revealed that the former exerted a good dispersion effect on the ceramic ink. The sedimentation ratio, zeta potential, surface tension, viscosity, and density of the inks were measured, and the Reynolds and Weber numbers, as well as Z value, were calculated. A stable, homogeneous, and high solid loading (20 wt%) ceramic ink could be achieved after aging for a period of 72 h. Finally, the ceramic inks showed the desired printable property in the inkjet printing process. Combining inkjet printing technology with a sintering process, Ni-Mn-O films have the potential to monitor temperature and humidity parameters for intelligent wearable devices.