Bhiksha Gugulothu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bhiksha Gugulothu has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
- Sivasundar Vijayakumar
Department of Mechanical Engineering, Saveetha School of Engineering, SIMATS, Saveetha University, Chennai, Tamil Nadu, India
4 shared publications A. Pradeep
Department of Mechanical Engineering
3 shared publicationsG. Krishna Mohana Rao
3 shared publicationsS. Vijayakumar
Department of Mechanical Engineering, BVC Engineering College (Autonomous), Odalarevu , India
3 shared publicationsDesta Kalbessa Kumsa
2 shared publicationsMinyahil Bezabih Kassa
2 shared publications
Latest Publications
- 14 August 2026
- Published by Springer Nature in Interactions
- Vol. 247 (1) , 382
Tool pin geometry design and material flow characteristics in friction stir welding of advanced composites: a comprehensive review
- 14 August 2026
- Published by Springer Nature in Interactions
- Vol. 247 (1) , 382
Tool pin geometry design and material flow characteristics in friction stir welding of advanced composites: a comprehensive review
- 9 February 2026
- Published by Springer Nature in Interactions
- Vol. 247 (1)
Development of stir-cast al 6063 hybrid composites with 5 Wt.% fly ash and varying SiC reinforcements for improved mechanical and impact properties
- 9 February 2026
- Published by Springer Nature in Interactions
- Vol. 247 (1)
Development of stir-cast al 6063 hybrid composites with 5 Wt.% fly ash and varying SiC reinforcements for improved mechanical and impact properties
- 30 June 2023
- Published by IGI Global Scientific Publishing
- p. 137-147
Electrical Discharge Machining Parameters and Dielectric Fluid
This chapter describes the basic working principle of electrical discharge machining. The impacts of both significant and insignificant machining parameters were also detailed. Also, the purpose, properties, and types of dielectric fluid were discussed to better understand the process. This chapter is concluded with describing the benefits of flushing with its types. The rapid impedance of cold dielectric fluid causes an explosive evacuation of molten metal from the electrode and workpiece surfaces. This results in the formation of a tiny crater on the surfaces of the two conductors, which hardens hollow balls of material that are subsequently drained from the gap by the fluid. Request access from your librarian to read this chapter's full text.
- 30 June 2023
- Published by IGI Global Scientific Publishing
- p. 137-147
Electrical Discharge Machining Parameters and Dielectric Fluid
This chapter describes the basic working principle of electrical discharge machining. The impacts of both significant and insignificant machining parameters were also detailed. Also, the purpose, properties, and types of dielectric fluid were discussed to better understand the process. This chapter is concluded with describing the benefits of flushing with its types. The rapid impedance of cold dielectric fluid causes an explosive evacuation of molten metal from the electrode and workpiece surfaces. This results in the formation of a tiny crater on the surfaces of the two conductors, which hardens hollow balls of material that are subsequently drained from the gap by the fluid. Request access from your librarian to read this chapter's full text.
- 30 June 2023
- Published by IGI Global Scientific Publishing
- p. 107-136
Electric Discharge Machining
In the last decade, there has been an increase in interest in electrical discharge machining (EDM)'s innovative applications, with a focus on this technology's potential for surface modification. Along with the erosion of the work material during machining, the inherent nature of the operation also causes some tool material to be lost. The surface composition after machining and, subsequently, its characteristics are influenced by the formation of plasma channel, which is composed of material vapours from the eroding work material and tool electrode, and pyrolysis of dielectric. Under appropriate machining circumstances, deliberate material transfer can be accomplished by distributing metallic powders in the dielectric or utilizing composite electrodes, or by combining the two. This study provides an overview of the phenomena of surface modification by electric discharge machining as well as potential future directions for its use. Request access from your librarian to read this chapter's full text.
- 30 June 2023
- Published by IGI Global Scientific Publishing
- p. 107-136
Electric Discharge Machining
In the last decade, there has been an increase in interest in electrical discharge machining (EDM)'s innovative applications, with a focus on this technology's potential for surface modification. Along with the erosion of the work material during machining, the inherent nature of the operation also causes some tool material to be lost. The surface composition after machining and, subsequently, its characteristics are influenced by the formation of plasma channel, which is composed of material vapours from the eroding work material and tool electrode, and pyrolysis of dielectric. Under appropriate machining circumstances, deliberate material transfer can be accomplished by distributing metallic powders in the dielectric or utilizing composite electrodes, or by combining the two. This study provides an overview of the phenomena of surface modification by electric discharge machining as well as potential future directions for its use. Request access from your librarian to read this chapter's full text.
- Open Access
- 1 March 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (3) , 035302
Manihot esculenta tuber microcrystalline cellulose and woven bamboo fiber-reinforced unsaturated polyester composites: mechanical, hydrophobic and wear behavior
In this research Manihot esculenta (cassava) tuber stem microcrystalline cellulose (MCC) and woven bamboo fiber (WBF) reinforced unsaturated polyester (UP) composites are prepared and tested. The main aim of this study was to synthesis the microcrystalline cellulose from Manihot esculenta tuber stem and investigate the mechanical, wear and hydrophobic properties of UP resin composite made using MCC and WBF. The laminated composites were prepared by the hand layup method and characterized according to ASTM standards. According to the results, the composite containing 40 vol% of WBF increased the tensile strength and modulus, flexural strength and modulus, interlaminar shear strength, Izod impact as well as hardness by 39%, 10%, 42%, 27%, 1%, 91%, and 1%, respectively as compare to pure polyester resin composites. In comparison to all composites, the composite with 4 vol% of MCC exhibits the lowest sp. wear rate of 0.011 mm3/Nm. The water absorption contact angle indicated that all composite designations had a wider contact angle of more than 70°, which indicates a stronger hydrophobicity of composites. The SEM fractography reveals improved bonding and toughness for 4 vol% of MCC and WBF reinforced UP composites. Such mechanically stronger, wear resistance, as well as high hydrophobic composites, could be used in aerospace, automobile, defence and industrial sector.
- 1 March 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (3) , 035302
Open AccessManihot esculenta tuber microcrystalline cellulose and woven bamboo fiber-reinforced unsaturated polyester composites: mechanical, hydrophobic and wear behavior
In this research Manihot esculenta (cassava) tuber stem microcrystalline cellulose (MCC) and woven bamboo fiber (WBF) reinforced unsaturated polyester (UP) composites are prepared and tested. The main aim of this study was to synthesis the microcrystalline cellulose from Manihot esculenta tuber stem and investigate the mechanical, wear and hydrophobic properties of UP resin composite made using MCC and WBF. The laminated composites were prepared by the hand layup method and characterized according to ASTM standards. According to the results, the composite containing 40 vol% of WBF increased the tensile strength and modulus, flexural strength and modulus, interlaminar shear strength, Izod impact as well as hardness by 39%, 10%, 42%, 27%, 1%, 91%, and 1%, respectively as compare to pure polyester resin composites. In comparison to all composites, the composite with 4 vol% of MCC exhibits the lowest sp. wear rate of 0.011 mm3/Nm. The water absorption contact angle indicated that all composite designations had a wider contact angle of more than 70°, which indicates a stronger hydrophobicity of composites. The SEM fractography reveals improved bonding and toughness for 4 vol% of MCC and WBF reinforced UP composites. Such mechanically stronger, wear resistance, as well as high hydrophobic composites, could be used in aerospace, automobile, defence and industrial sector.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2764 (1)
Optimization of process parameters by response surface methodology using Box-Behnken method on electrical discharge machining of Ti-6Al-4VAlloy
In this research paper, drinking water was used as a dielectric fluid, and EDM parameters such as pulse on and off times, discharge current, and graphite powder concentration were used to machine Ti-6Al-4V. A graphite powder concentration of 4.5 grams per liter, 9 grams per liter, and 13.5 grams per liter was mixed in water. An orthogonal array based on Taguchi L15 was used to conduct the experiments. Processes of significance analyzing the variance (ANOVA) was done for each parameter. Additionally, micro hardness tests and EDAX analysis were also carried out. The purpose of this research was to increase the MRR and reduce the Ra and recast layer thickness (RLT).
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2764 (1)
Open AccessOptimization of process parameters by response surface methodology using Box-Behnken method on electrical discharge machining of Ti-6Al-4VAlloy
In this research paper, drinking water was used as a dielectric fluid, and EDM parameters such as pulse on and off times, discharge current, and graphite powder concentration were used to machine Ti-6Al-4V. A graphite powder concentration of 4.5 grams per liter, 9 grams per liter, and 13.5 grams per liter was mixed in water. An orthogonal array based on Taguchi L15 was used to conduct the experiments. Processes of significance analyzing the variance (ANOVA) was done for each parameter. Additionally, micro hardness tests and EDAX analysis were also carried out. The purpose of this research was to increase the MRR and reduce the Ra and recast layer thickness (RLT).
- Open Access
- 12 September 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-9
Optimization of Stir-Squeeze Casting Parameters to Analyze the Mechanical Properties of Al7475/B4C/Al2O3/TiB2 Hybrid Composites by the Taguchi Method
Optimization of Stir-Squeeze Casting Parameters to Analyze the Mechanical Properties of Al7475/B4C/Al2O3/TiB2 Hybrid Composites by the Taguchi Method: Stir-squeeze casting (SSC) is the appropriate and inexpensive technique for producing aluminum hybrid matrix composites as it creates a uniform distribution of reinforcements in the composite with finer grains. Al7475 is a lightweight castable alloy that possesses enough hardness and strength with applications in automotive and aerospace. This research work examines the effect of process parameters for Al7475/Al2O3/B4C/TiB2 hybrid matrix composites produced by the stir-squeeze casting methodology. As per Taguchi design L16, four parameters with four levels were selected in the optimization process of SSC are stir speed (SD) of 300-450rpm, melting temperature (ME) of 750900°C, squeeze pressure (SE) of 50-125MPa, and reinforcement (RT) of 2-8 wt. The mechanical properties such as tensile strength (TS) and hardness (HN) are studied by the variation of each process parameters levels. The optimization results on TS and HN are predicted by Minitab-17 Software. It is observed that maximum TS of 325MPa and HN of 130.6 Hv are attained at experiments L1 and L7, respectively. From the SN ratio result, the TS value is improved at the parameter level of RT2-SE4-ME2-SD4. The ANOVA result exposed that reinforcement is the most significant factor for enhancing tensile strength which contributes 38.9, followed by squeeze pressure of 28.4, stir speed of 13.6, and melting temperature of 12.16.
- 12 September 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-9
Open AccessOptimization of Stir-Squeeze Casting Parameters to Analyze the Mechanical Properties of Al7475/B4C/Al2O3/TiB2 Hybrid Composites by the Taguchi Method
Optimization of Stir-Squeeze Casting Parameters to Analyze the Mechanical Properties of Al7475/B4C/Al2O3/TiB2 Hybrid Composites by the Taguchi Method: Stir-squeeze casting (SSC) is the appropriate and inexpensive technique for producing aluminum hybrid matrix composites as it creates a uniform distribution of reinforcements in the composite with finer grains. Al7475 is a lightweight castable alloy that possesses enough hardness and strength with applications in automotive and aerospace. This research work examines the effect of process parameters for Al7475/Al2O3/B4C/TiB2 hybrid matrix composites produced by the stir-squeeze casting methodology. As per Taguchi design L16, four parameters with four levels were selected in the optimization process of SSC are stir speed (SD) of 300-450rpm, melting temperature (ME) of 750900°C, squeeze pressure (SE) of 50-125MPa, and reinforcement (RT) of 2-8 wt. The mechanical properties such as tensile strength (TS) and hardness (HN) are studied by the variation of each process parameters levels. The optimization results on TS and HN are predicted by Minitab-17 Software. It is observed that maximum TS of 325MPa and HN of 130.6 Hv are attained at experiments L1 and L7, respectively. From the SN ratio result, the TS value is improved at the parameter level of RT2-SE4-ME2-SD4. The ANOVA result exposed that reinforcement is the most significant factor for enhancing tensile strength which contributes 38.9, followed by squeeze pressure of 28.4, stir speed of 13.6, and melting temperature of 12.16.
- Open Access
- 28 August 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-7
Design and Fabrication of Patient-Specific Implant for Maxillofacial Surgery Using Additive Manufacturing
Patient-specific implants are well known for fixing the fracture for bone repairs. However, the exact fixation of the fabricated implant to the patients is a challenging task. To overcome this problem, in the present study two kinds of designs are developed and fabricated. Based on the exact fitting to the patient’s oral system, the best design is selected to fabricate. Computed tomography (CT) scan data of the patient oral anatomy is converted into a 3D model using the DICOM Software “Slicer 3D.” The patient-specific maxillofacial implant is fabricated using fused filament fabrication (FFF) and direct metal laser sintering (DMLS) techniques. Before fabricating real time product, a prototype is fabricated at the initial stage using FFF. Later, stress distribution and displacement of the implant was investigated using a FEM simulation. The conclusion of the present work results are potential for FFF of patient-specific implants out of Ti-6Al-4V.
- 28 August 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-7
Open AccessDesign and Fabrication of Patient-Specific Implant for Maxillofacial Surgery Using Additive Manufacturing
Patient-specific implants are well known for fixing the fracture for bone repairs. However, the exact fixation of the fabricated implant to the patients is a challenging task. To overcome this problem, in the present study two kinds of designs are developed and fabricated. Based on the exact fitting to the patient’s oral system, the best design is selected to fabricate. Computed tomography (CT) scan data of the patient oral anatomy is converted into a 3D model using the DICOM Software “Slicer 3D.” The patient-specific maxillofacial implant is fabricated using fused filament fabrication (FFF) and direct metal laser sintering (DMLS) techniques. Before fabricating real time product, a prototype is fabricated at the initial stage using FFF. Later, stress distribution and displacement of the implant was investigated using a FEM simulation. The conclusion of the present work results are potential for FFF of patient-specific implants out of Ti-6Al-4V.
- 11 March 2022
- Published by Elsevier in Materials Today: Proceedings
- Vol. 62, 2115-2118
Process parameter optimization for tensile strength and Hardness of Al-MMC using RSM technique
- 11 March 2022
- Published by Elsevier in Materials Today: Proceedings
- Vol. 62, 2115-2118
Process parameter optimization for tensile strength and Hardness of Al-MMC using RSM technique