Zhiqiang Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhiqiang Zhang has a total of 108 co-authors. Here are the top co-authors by number of shared publications:
Tiangang Zhang
10 shared publicationsXuecheng Lu
Civil Aviation University of China
5 shared publicationsPan Gong
Huazhong University of Science and Technology
4 shared publications- Tiangang Zhang
College of Aeronautical Engineering, Civil Aviation University of China, Tianjin 300300, China
4 shared publications Dongquan Wu
Sino‐European Institute of Aviation Engineering Civil Aviation University of China Tianjin 300300 China
3 shared publicationsHongli Liu
College of Aeronautical Engineering, Civil Aviation University of China, Tianjin, China
3 shared publications
Latest Publications
- 27 September 2026
- Published by Elsevier in Tribology International
- Vol. 227
Effects of heat treatment and titanium modification on the microstructure and tribological properties of CMT-processed 2024 aluminum alloy
- 27 September 2026
- Published by Elsevier in Tribology International
- Vol. 227
Effects of heat treatment and titanium modification on the microstructure and tribological properties of CMT-processed 2024 aluminum alloy
- 7 September 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (41) , 42944-42966
The Effect of Laser Oscillation Frequency on the Microstructure and Properties of a Novel Low-Density Aluminum Alloy in Laser-Cold Metal Transfer Hybrid Welded Joints
- 7 September 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (41) , 42944-42966
The Effect of Laser Oscillation Frequency on the Microstructure and Properties of a Novel Low-Density Aluminum Alloy in Laser-Cold Metal Transfer Hybrid Welded Joints
- 11 August 2026
- Published by Taylor & Francis in International Journal of Computer Integrated Manufacturing
- p. 1-67
Machine learning in additive manufacturing of aluminum alloys: a review of fundamentals, challenges, and evolution of intelligent pathways
1. Additive manufacturing (AM), commonly known as 3D printing, is profoundly transforming traditional industrial production as a core pillar of the digital intelligent manufacturing paradigm. This ...
- 11 August 2026
- Published by Taylor & Francis in International Journal of Computer Integrated Manufacturing
- p. 1-67
Machine learning in additive manufacturing of aluminum alloys: a review of fundamentals, challenges, and evolution of intelligent pathways
1. Additive manufacturing (AM), commonly known as 3D printing, is profoundly transforming traditional industrial production as a core pillar of the digital intelligent manufacturing paradigm. This ...
- 20 June 2026
- Published by Elsevier in Optics & Laser Technology
- Vol. 203
Simulation and experimental study of variable-frequency laser cleaning of composite coating on aluminum alloy surface
- 20 June 2026
- Published by Elsevier in Optics & Laser Technology
- Vol. 203
Simulation and experimental study of variable-frequency laser cleaning of composite coating on aluminum alloy surface
- Open Access
- 20 May 2026
- Published by Elsevier in SSRN Electronic Journal
Study on the Microstructure and Properties of PE-HAS NiCrMoAl-x%AT Composite Coatings Fabricated via Wire-Powder Co-Melting
A series of NiCrMoAl-x%AT cermet composite anti-skid coatings were prepared using plasma-enhanced high-velocity arc spraying (PE-HAS) technology, with NiCrMoAl alloy wire (2.0 mm in diameter) and AT ceramic powder (average particle size of 35 μm, consisting of Al2O3 and Ti2O3) as feedstocks, under different wire-to-powder feeding ratios. The microstructure, mechanical properties, corrosion resistance, and tribological performance of the coatings were comprehensively investigated. The results indicate that all composite coatings with varying ceramic contents exhibit relatively high surface roughness and a high friction coefficient. As the AT content increases, the microhardness and wear resistance of the coatings improve significantly, which is attributed to the presence of multiple locally reinforced regions composed of different forms of ceramic phases that resist abrasive action. The wear mechanisms of the coatings are identified as abrasive wear and adhesive wear, and the wear resistance mechanism is hard-phase strengthening. However, excessively high ceramic feeding rates lead to incomplete melting or rebound of the ceramic powder, resulting in a decrease in the deposition rate of the ceramic within the coating and consequently degraded coating performance. Furthermore, the unique dual feeding method promotes the formation of an in-situ bilayer structure in coatings with high ceramic content, further enhancing their wear resistance and corrosion resistance.
- 20 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessStudy on the Microstructure and Properties of PE-HAS NiCrMoAl-x%AT Composite Coatings Fabricated via Wire-Powder Co-Melting
A series of NiCrMoAl-x%AT cermet composite anti-skid coatings were prepared using plasma-enhanced high-velocity arc spraying (PE-HAS) technology, with NiCrMoAl alloy wire (2.0 mm in diameter) and AT ceramic powder (average particle size of 35 μm, consisting of Al2O3 and Ti2O3) as feedstocks, under different wire-to-powder feeding ratios. The microstructure, mechanical properties, corrosion resistance, and tribological performance of the coatings were comprehensively investigated. The results indicate that all composite coatings with varying ceramic contents exhibit relatively high surface roughness and a high friction coefficient. As the AT content increases, the microhardness and wear resistance of the coatings improve significantly, which is attributed to the presence of multiple locally reinforced regions composed of different forms of ceramic phases that resist abrasive action. The wear mechanisms of the coatings are identified as abrasive wear and adhesive wear, and the wear resistance mechanism is hard-phase strengthening. However, excessively high ceramic feeding rates lead to incomplete melting or rebound of the ceramic powder, resulting in a decrease in the deposition rate of the ceramic within the coating and consequently degraded coating performance. Furthermore, the unique dual feeding method promotes the formation of an in-situ bilayer structure in coatings with high ceramic content, further enhancing their wear resistance and corrosion resistance.
- Open Access
- 21 April 2026
- Published by Elsevier in SSRN Electronic Journal
Investigation into the Tribocorrosion Behavior of Laser Cladding Titanium Matrix Composite Coatings with Y2O3 Addition
Y2O3-modified titanium-based composite coatings were fabricated on Ti6Al4V titanium alloy substrates using coaxial powder feeding laser cladding technology. The influence of Y2O3 addition on the microstructure and tribocorrosion properties of the coatings was systematically investigated. The results indicate that coatings with different Y2O3 contents consist of a β-Ti matrix, TiC reinforcing phase, and other phases such as Ti2Ni, Ti2S and TiS3. Compared with the coating without Y2O3, the microstructure of the coating with 4 wt.% Y2O3 was significantly refined, with coarse dendrites transforming into fine particles. Tribocorrosion tests in a 3.5 wt.% NaCl solution revealed that the volumetric wear rate of the modified coating was significantly reduced by 74.3% and 50.0%, respectively, compared to the substrate and the unmodified coating. First-principles calculations further revealed that the low surface energy of TiS3 and the high work function of TiC synergistically enhance the anti-adhesion and corrosion resistance properties of coatings.
- 21 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInvestigation into the Tribocorrosion Behavior of Laser Cladding Titanium Matrix Composite Coatings with Y2O3 Addition
Y2O3-modified titanium-based composite coatings were fabricated on Ti6Al4V titanium alloy substrates using coaxial powder feeding laser cladding technology. The influence of Y2O3 addition on the microstructure and tribocorrosion properties of the coatings was systematically investigated. The results indicate that coatings with different Y2O3 contents consist of a β-Ti matrix, TiC reinforcing phase, and other phases such as Ti2Ni, Ti2S and TiS3. Compared with the coating without Y2O3, the microstructure of the coating with 4 wt.% Y2O3 was significantly refined, with coarse dendrites transforming into fine particles. Tribocorrosion tests in a 3.5 wt.% NaCl solution revealed that the volumetric wear rate of the modified coating was significantly reduced by 74.3% and 50.0%, respectively, compared to the substrate and the unmodified coating. First-principles calculations further revealed that the low surface energy of TiS3 and the high work function of TiC synergistically enhance the anti-adhesion and corrosion resistance properties of coatings.
- 24 March 2026
- Published by Springer Nature in Applied Physics A
- Vol. 132 (4) , 319
Simulation and experimental study on UV laser removal of composite paint layers from civil aircraft skins at variable scan speeds
- 24 March 2026
- Published by Springer Nature in Applied Physics A
- Vol. 132 (4) , 319
Simulation and experimental study on UV laser removal of composite paint layers from civil aircraft skins at variable scan speeds
- 3 November 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (1)
Effect of Travel Speed on Microstructure Evolution of Cold Metal Transfer with Pulse Wire Arc Additive Manufacturing AA2024
This study investigates the effect of arc travel speed (TS) on molten pool morphology, grain structure, crystallographic texture, and grain boundaries in cold metal transfer with pulse hybrid wire arc additive manufacturing of AA2024 alloy. Deposits are fabricated at TS of 7.2, 7.9, and 8.6 mm s −1 . Electron backscatter diffraction is used to examine grain orientation, size, and dislocation distribution in the molten pool zone (MPZ), molten pool boundary zone (MPB), and molten pool transition zone (MTZ). Porosity varies nonmonotonically with TS, reaching a minimum at 7.9 mm s −1 . Higher TS reduces heat input and accelerates droplet transfer, producing flatter pools with finer, more uniform grains. Grain size decreases and equiaxed fraction increases in MPB and MPZ, while equiaxed formation becomes more pronounced in MTZ. Q and U textures weaken with higher TS; MTZ exhibits increased low‐angle grain boundary density; and Σ3 boundary fraction peaks at 7.9 mm s −1 , indicating strain energy release and reduced grain deformation. Tensile properties improve with TS, reaching 289.1 MPa ultimate tensile strength and 11.6% elongation at 8.6 mm s −1 . Anisotropy results from grain refinement, higher equiaxed fraction, weakened texture, and low porosity.
- 3 November 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (1)
Effect of Travel Speed on Microstructure Evolution of Cold Metal Transfer with Pulse Wire Arc Additive Manufacturing AA2024
This study investigates the effect of arc travel speed (TS) on molten pool morphology, grain structure, crystallographic texture, and grain boundaries in cold metal transfer with pulse hybrid wire arc additive manufacturing of AA2024 alloy. Deposits are fabricated at TS of 7.2, 7.9, and 8.6 mm s −1 . Electron backscatter diffraction is used to examine grain orientation, size, and dislocation distribution in the molten pool zone (MPZ), molten pool boundary zone (MPB), and molten pool transition zone (MTZ). Porosity varies nonmonotonically with TS, reaching a minimum at 7.9 mm s −1 . Higher TS reduces heat input and accelerates droplet transfer, producing flatter pools with finer, more uniform grains. Grain size decreases and equiaxed fraction increases in MPB and MPZ, while equiaxed formation becomes more pronounced in MTZ. Q and U textures weaken with higher TS; MTZ exhibits increased low‐angle grain boundary density; and Σ3 boundary fraction peaks at 7.9 mm s −1 , indicating strain energy release and reduced grain deformation. Tensile properties improve with TS, reaching 289.1 MPa ultimate tensile strength and 11.6% elongation at 8.6 mm s −1 . Anisotropy results from grain refinement, higher equiaxed fraction, weakened texture, and low porosity.
- 3 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (14) , 13364-13384
Effect of Arc Travel Speed on Corrosion Resistance of AA2024 by Cold Metal Transfer with Pulsed Wire Arc Additive Manufacturing
- 3 November 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (14) , 13364-13384
Effect of Arc Travel Speed on Corrosion Resistance of AA2024 by Cold Metal Transfer with Pulsed Wire Arc Additive Manufacturing
- 31 October 2025
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 34 (8) , 3440-3454
Effect of Wire Diameter on the Microstructure and Properties of Al-Based Coatings by Plasma-enhanced High-Velocity Arc Spraying
- 31 October 2025
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 34 (8) , 3440-3454
Effect of Wire Diameter on the Microstructure and Properties of Al-Based Coatings by Plasma-enhanced High-Velocity Arc Spraying