CÖCengiz Özel

Cengiz Özel

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Cengiz Özel has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Investigation of Physical, Mechanical, Durability, and Radiation Shielding Properties of Siderite-Based Shotcrete

    by H. Polat, C. Özel, F. Akman, M. R. Kaçal, H. Oğul, A. Turşucu

    In this study, the physical, mechanical, durability, and radiation shielding properties of wet-mix shotcrete (SC) containing crushed stone (CS), ferrochrome slag (FS), and siderite (S) aggregates were investigated. S aggregate replaced FS at 25%, 50%, 75%, and 100% to produce various SC groups. Physical and mechanical properties, including density, ultrasonic pulse velocity (UPV), and compressive, flexural, and splitting tensile strengths, were examined. Durability was assessed through freeze–thaw and sulfate resistance tests. Gamma radiation shielding was evaluated using a high-purity germanium (HPGe) detector with sources emitting 276.5–1,332.5 keV energies. The mass attenuation coefficient ( μ / ρ ), linear attenuation coefficients ( μ ), half-value layer (HVL), tenth-value layer (TVL), mean free path (MFP), and radiation protection efficiency (REF) were determined. Experimental results were compared with theoretical (WinXCOM) and simulation (FLUKA) data. Increasing siderite content enhanced both gamma attenuation and mechanical strength. The findings suggest that siderite-based shotcrete is suitable for radiation protection applications.

  • Open Access

    Experimental Investigation of Polymer-Modified Bituminous Stone Mastic Asphalt Mixtures Containing Cellulose Acetate Recycled from Cigarette Butts

    by Hande Varol Morova, Cengiz Özel

    Stone Mastic Asphalt (SMA) mixtures exhibit superior performance under traffic loads due to the high content of coarse aggregates; however, the high bitumen content also leads to the problem of bitumen drainage from the mixture. Several studies have been conducted on the use of stabilizing additives such as fibers, polymers, or mineral fillers to reduce binder drainage in SMA mixtures. In this study, however, an innovative and sustainable solution was developed to address the bitumen drainage problem encountered in SMA pavements and to improve the long-term performance of the mixture. In this context, the feasibility of using cellulose acetate (SG) material recycled from cigarette butts as an alternative fiber additive to the traditionally used cellulose fiber (SL) was investigated. This method aims to achieve both environmental benefits in terms of waste management and economic advantages in terms of additive materials. Additionally, the effect of using different SL contents (0.1%, 0.2%, 0.3%, 0.4%, 0.5%) on mixture performance was examined. Within this scope, both pure bitumen (B) and Elvaloy RET + PPA (E)-modified bitumen (1.6%, 1.7%, and 1.8% Elvaloy RET + 0.2% PPA) were used to produce both fiber-reinforced and non-fiber-reinforced SMA mixtures. Traditional and Superpave tests were conducted to determine the rheological and physical properties of the pure and modified binders. All SMA specimens were tested for Marshall stability and flow, Marshall quotient, indirect tensile strength (ITS), tensile strength ratio (TSR), Schellenberg bitumen drainage, sand patch, and Cantabro particle loss. Furthermore, a cost analysis was carried out to evaluate the economic effect of different fiber types and proportions. Among the SMA mixtures, the highest stability and resistance to moisture damage were achieved in the mixtures containing 1.6% Elvaloy RET + 0.2% PPA with 0.3–0.4% SG and 1.7% Elvaloy RET + 0.2% PPA with 0.3–0.4% SL, while the optimum surface texture depth was obtained in the mixtures containing 1.6–1.7% Elvaloy RET + 0.2% PPA with 0.3% SG. In conclusion, the Elvaloy RET + PPA modification enhanced the aging resistance of the bitumen, while the SG fibers used at 0.3–0.4% fiber content in the 1.6–1.7% Elvaloy RET + 0.2% PPA-modified series were identified as a promising mechanical and economic alternative to conventional SL fibers.


  • Cellulose and its derivatives as biodegradable materials: A review

    by Muhammed Zakir Tufan, Cengiz Özel

    From ancient times to the present day, human beings have carried out many studies to make their lives easier. As a result of these studies, they aimed to discover something new. With the industrial revolution, petrochemical materials began to be produced. The fact that these materials have gone through various chemical stages has become a threat to human health. In addition, the fact that petroleum-derived materials remain in nature for centuries without degrading, and the parallel increase in environmental problems has led humanity to search for different resources. In this work, general information is given about the types of derivatives obtained from cellulose, which is the most common in nature.


  • Basınç Dayanımı Açısından Püskürtme Beton Uygulamalarındaki Başlık Sistemlerinin Değerlendirmesi

    by Hasan Polat, Cengiz Özel

    Bu çalışmada, farklı başlık tiplerinin püskürtme betonunun basınç dayanımı üzerindeki etkisi incelenmiştir. Yapılan bu çalışmada, başlıksız (kontrol), kükürt başlıklı ve neopren başlıklı olmak üzere üç farklı başlık sisteminin etkisi değerlendirmiştir. Deneyler kapsamında her bir başlık sistemi için dokuz farklı numune üzerinde testler gerçekleştirilmiştir. Elde edilen sonuçlar, başlıksız numunelerin kükürt başlık ve neopren başlığa kıyasla daha düşük basınç dayanımı gösterdiğini belirlenmiştir. Bu sonuçlar, başlık kullanımının önemini vurgulamaktadır. Ayrıca, kükürt başlık sistemine alternatif olarak sunulan neopren başlığın, kükürt başlık sistemine göre % 2.96 daha yüksek ortalama basınç dayanımı değeri sunduğu belirlenmiştir. Bu durum, numune başlık birleşim bölgelerinde oluşan gerilme yığılmalarından kaynaklanabileceği şeklinde yorumlanmıştır. Çalışmanın sonuçları, püskürtme betonunun başlık seçiminin ve başlık-beton etkileşiminin, malzemenin basınç dayanımı özellikleri üzerinde önemli bir rol oynayabileceğini göstermektedir. Sonuç olarak günümüzde laboratuvarda yaygın olarak kullanılan kükürt başlıklamaya alternatif olarak neopren başlık sistemlerin tavsiye edilebileceği sonucuna varılmıştır.

  • Open Access

    INVESTIGATION OF PHYSICAL AND MECHANICAL PROPERTIES OF LIGHTWEIGHT CONCRETES WITH POLYMER BINDERS

    by Ali Nadi Kaplan, Cengiz Özel

    Bu çalışmada, polimer bağlayıcı olarak vinilester reçine ve hafif agrega olarak pomza ile genleştirilmiş perlit agregalarının kullanıldığı polimer beton kompozitleri üretilmiştir. Beton karışımlarında kullanılan agregalar hacimce %0, %15, %30 ve %45 oranlarında belirlenmiş ve belirlenen karışım oranlarında üretilen polimer beton numuneleri üzerinde bir dizi deneysel çalışma gerçekleştirilmiştir. Bu kapsamda polimer beton numunelerinin teorik yoğunlukları ile görünür yoğunlukları karşılaştırılmış, boyuna dalga hızı deneyi yapılmıştır. Numunelerin mekanik özellikleri için eğilme ve basınç deneyleri yapılarak polimer betonların dayanımları belirlenmiştir. Mekanik ve fiziksel özelliklerin kullanılan agrega tipine ve oranına göre değiştiği ortaya çıkmıştır. Her iki agregalı polimer beton serileri incelendiğinde pomza kullanılarak üretilen numunelerin eğilme ve basınç dayanımlarının genleştirilmiş perlit kullanılarak üretilen numunelerden daha yüksek değerlerde olduğu görülmüştür. Çalışmada en yüksek dayanım değerlerini %30 pomza agregası kullanılarak üretilen polimer beton numuneleri sağlamıştır. Bu numunelerde eğilme dayanımı 44 MPa, basınç dayanımı 122 MPa’dır. Son olarak agrega oranının artışına bağlı olarak eğilme dayanımları pomzalı serilerde önce artıp sonra azalışa geçmişken, genleştirilmiş perlitli serilerde azalış göstermiştir. Basınç dayanımları ise her iki agregalı serilerde de önce artmış daha sonra azalışa geçmiştir.

  • Open Access

    Farklı Priz Hızlandırıcı Katkıların Püskürtme Beton Performansına Karşılaştırmalı Analizi

    by Hasan Polat, Cengiz Özel

    Dayanım, aderans, donma/çözülme ve aşınma direnci özelliklerini iyileştirmek ve geri tepmeyi azaltmak için püskürtme betona çeşitli priz hızlandırıcı katkı maddeleri ve karışımlar eklenir. Priz hızlandırıcılar hem kuru hem de ıslak karışım püskürtme beton uygulamalarında giderek daha fazla kullanılmaktadırlar. Priz hızlandırıcılar, erken yaş dayanımı artırmak, tozu ve geri tepmeyi azaltmak için kuru karışım uygulamalarında yaygın olarak kullanılırken, ıslak karışımda hızlı sertleşme ve erken mukavemet elde etmek için kullanılırlar. Yapılan bu çalışmada ıslak karışım püskürtme betonlarda kullanılan sıvı priz hızlandırıcı katkıların optimum değerleri araştırılmıştır. Priz hızlandırıcı katkı miktarı kullanılan çimento miktarının %0 (kontrol), %2, %4, %6 ve %8 oranlarında kullanılarak püskürtme beton numuneleri üretilmiştir. Üretilen numuneler üzerinde, priz süresi tayini, basınç dayananımı (1gün, 7gün, 28 gün) deneyleri yapılmış ve iç yapı analizleri ile incelenmiştir. Çalışmada çimento olarak CEM I 42,5 R tipi çimento kullanılmış olup, katkı olarak alkali içeren ve içeremeyen iki farklı kimyasal katkı kullanılmış, su/çimento oranı 0,32 olarak sabit tutulmuştur. Yapılan deneyler sonucunda, alkali içeren katkılarda %4’den yüksek, alkali içermeyen katkı türünde ise %8’den yüksek katkı kullanımın uygun olduğu belirlenmiştir. Ayrıca 1 ve 7 günlük basınç dayanımlarında priz hızlandırıcı katkı etkisinin bariz bir şekilde görüldüğü 28 günde ise kontrol betonun basınç dayanımına göre yaklaşık %22 oranında bir azalma meydana geldiği görülmüş olup yapılan içyapı analizleriyle bu durum desteklenmiştir.

  • Open Access

    The Effects of Water/Cement Ratio and Cement Dosage Variables on the Performance of Shotcrete: Compressive Strength and Drying Shrinkage Perspective

    by Hasan Polat, Cengiz Özel

    Shotcrete is a construction material that is applied by spraying under high pressure, and there are many factors that affect its properties. In this study, the effect of cement dosage and water-to-cement ratio on the compressive strength and drying shrinkage performance of shotcrete was investigated. For this purpose, shotcrete specimens were produced using three different water-to-cement ratios (0.40, 0.45, 0.50) and three different cement dosages (400, 450, 500). The unit weight, ultrasonic pulse velocity (UPV), compressive strength, splitting tensile strength, and drying shrinkage performance of the produced specimens were examined. As a result of the experimental studies, an increase in cement dosage resulted in an increase in unit weight values, with the amount of increase ranging from approximately 1% to 3%. When the UPV value was examined, an increase in cement dosage resulted in an increase in UPV values, with an increase of approximately 1% to 5%. An increase in cement dosage also resulted in an increase in compressive strength and splitting tensile strength values, with the increase ranging from approximately 12%-16%, 5%-9%, and 10%-12% for the 500, 450, and 400 dosage groups, respectively. The drying shrinkage values increased with increasing cement dosage, the highest shrinkage values occurred in the groups with 0.50 water/cement ratio and 500 dosage, and it was observed that 85-95% of the total shrinkage of the shotcrete specimens was completed within the first 1 hour. Furthermore, the data obtained can be used to determine the optimum water/cement ratio and cement dosage for the construction of shotcrete.