Denis Vasko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Denis Vasko has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Ján Kardoš
Department of Robotics and Cybernetics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology in Bratislava, Bratislava, Slovakia
3 shared publications - Eva Miklovičová
Institute of Robotics and Cybernetics, Faculty of Electrical Engineering and Information Technology Slovak University of Technology in Bratislava, Ilkovičova 3, Bratislava, 841 04, Slovakia
2 shared publications - Jana Paulusová
Department of Robotics and Cybernetics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology in Bratislava, Bratislava, Slovakia
1 shared publication - Kristína Okienková
Department of Robotics and Cybernetics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology in Bratislava, Bratislava, Slovakia
1 shared publication - Marián Tárník
Department of Robotics and Cybernetics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology in Bratislava, Bratislava, Slovakia
1 shared publication - Róbert Málik
Department of Robotics and Cybernetics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology in Bratislava, Bratislava, Slovakia
1 shared publication
Latest Publications
- Open Access
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 143869-143882
Robust Control of a MIMO Laboratory Motion System Using Variable Structure Control and the Computed Torque Method With the Velocity Limitation
In this study, we experimentally verified a robust control law based on variable structure control and the computed torque method on a laboratory motion system. Variable structure control is characterized by high-frequency switching control, which does not have to be applicable to real motion systems. Therefore, we used a suitable reaching law to create a continuous substitution for the discontinuous nonlinear control law. This continuous substitution caused the loss of control invariance to parametric and signal disturbances, but the control loop remained robust, with bounded position errors. We augmented the variable structure control with the computed torque method, which ensured the feedback linearization of the dynamic system. The proposed design of the control law also considered the velocity constraints of the system. Both components of the control law needed to be considered in the velocity limitation, otherwise, the system constraints would be violated. We designed a velocity limitation algorithm for variable structure control to be compatible with the computed torque method, with regard to the desired performance, with exponential convergence and no overshoot. The control law is shown to satisfy the control objectives, and the results are discussed.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 143869-143882
Open AccessRobust Control of a MIMO Laboratory Motion System Using Variable Structure Control and the Computed Torque Method With the Velocity Limitation
In this study, we experimentally verified a robust control law based on variable structure control and the computed torque method on a laboratory motion system. Variable structure control is characterized by high-frequency switching control, which does not have to be applicable to real motion systems. Therefore, we used a suitable reaching law to create a continuous substitution for the discontinuous nonlinear control law. This continuous substitution caused the loss of control invariance to parametric and signal disturbances, but the control loop remained robust, with bounded position errors. We augmented the variable structure control with the computed torque method, which ensured the feedback linearization of the dynamic system. The proposed design of the control law also considered the velocity constraints of the system. Both components of the control law needed to be considered in the velocity limitation, otherwise, the system constraints would be violated. We designed a velocity limitation algorithm for variable structure control to be compatible with the computed torque method, with regard to the desired performance, with exponential convergence and no overshoot. The control law is shown to satisfy the control objectives, and the results are discussed.
- Open Access
- 29 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 104846-104856
Saturated Switching Functions for Sliding Mode Control With Speed Error Limitation
The saturated non-singular terminal switching function (SNTSF) for sliding mode control with speed error limitation and finite-time error convergence is proposed. The sliding-mode dynamics and the boundary layer dynamics of the SNTSF are analyzed. It is also shown that the non-singular terminal switching function does not have a higher boundary layer position tracking precision than the linear switching function, contrary to some previous claims in the literature. An SNTSF sliding mode controller with speed error limitation and finite-time convergence is proposed and tested both simulatively and experimentally on a laboratory DC motor system.
- 29 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 104846-104856
Open AccessSaturated Switching Functions for Sliding Mode Control With Speed Error Limitation
The saturated non-singular terminal switching function (SNTSF) for sliding mode control with speed error limitation and finite-time error convergence is proposed. The sliding-mode dynamics and the boundary layer dynamics of the SNTSF are analyzed. It is also shown that the non-singular terminal switching function does not have a higher boundary layer position tracking precision than the linear switching function, contrary to some previous claims in the literature. An SNTSF sliding mode controller with speed error limitation and finite-time convergence is proposed and tested both simulatively and experimentally on a laboratory DC motor system.
- Open Access
- 22 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 134157-134163
Variable Structure Control of Second Order Systems With Nonlinear Uncertain Discontinuous Input Functions Using Approximate Inverses
We consider second order nonlinear systems in control canonical form, where the functional relation between the control variable and the system acceleration is nonlinear, uncertain and discontinuous. We approximate the nonlinear uncertain and discontinuous function with an invertible one, and use variable structure control theory to suppress the error of the approximate inverse. We rewrite the finite time reaching law or the terminal reaching law into the form of inequalities and use these inequalities to design a control law that drives the system state to the sliding surface in finite time, and one that ensures the convergence of the system speed and position errors to a narrow, adjustable width band around zero. The stability of the control system is also analyzed and proven. We demonstrate how to ensure the sufficiency of the available control effort, by the proper design of control parameters. The method is then validated on a numerical model of a nonlinear system with nonlinear, uncertain and discontinuous input function.
- 22 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 134157-134163
Open AccessVariable Structure Control of Second Order Systems With Nonlinear Uncertain Discontinuous Input Functions Using Approximate Inverses
We consider second order nonlinear systems in control canonical form, where the functional relation between the control variable and the system acceleration is nonlinear, uncertain and discontinuous. We approximate the nonlinear uncertain and discontinuous function with an invertible one, and use variable structure control theory to suppress the error of the approximate inverse. We rewrite the finite time reaching law or the terminal reaching law into the form of inequalities and use these inequalities to design a control law that drives the system state to the sliding surface in finite time, and one that ensures the convergence of the system speed and position errors to a narrow, adjustable width band around zero. The stability of the control system is also analyzed and proven. We demonstrate how to ensure the sufficiency of the available control effort, by the proper design of control parameters. The method is then validated on a numerical model of a nonlinear system with nonlinear, uncertain and discontinuous input function.