Aleksey Smerdov
Research Subjects
Aleksey Smerdov has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Roman Alexandrovich Rozov
Pavlov First Saint Petersburg State Medical University
3 shared publications - Vladimir N. Trezubov
Pavlov First St. Petersburg State Medical University
3 shared publications - Marat Z. Ertuvkhanov
National Medical Research Center «Central Research Institute of Dentistry and Maxillofacial Surgery», Moscow, Russian Federation
2 shared publications - S.N. Andreeva
Russian University of Medicine
2 shared publications - Максим Мишнев
Yaroslav-the-Wise Novgorod State University
2 shared publications - Andreev M.M.
Pirogov Russian National Research Medical University (Pirogov Medical University), Moscow, Russian Federation
1 shared publication
Latest Publications
- 30 September 2023
- Published by PNRPU Publishing House in Российский журнал биомеханики
- Vol. 27 (3) , 24-35
Трехмерный конечно-элементный анализ влияния утраты дентального имплантата на распределение напряжения в имплантационном протезе нижней челюсти.
Имплантационный протез может иметь всего три опорных имплантата, и утрата одного из них может повлечь за собой потерю всей конструкции. Каркасом конструкции Trefoil является стандартная балка из высокопрочного титана. При циклическом нагружении металлов и металлических конструкций возникает эффект, уменьшающий прочностные характеристики – усталость. Предел усталости – значение напряжений, ниже которых разрушить конструкцию циклической нагрузкой невозможно. Целью работы является выбор тактики ведения пациента с утратой дистального имплантата и ее обоснование на основании результатов трехмерного конечно-элементного анализа влияния утраты одного дентального имплантата на биомеханику имплантационного протеза нижней челюсти с тремя опорами. Моделирование нагружения мостовидного протеза осуществлялось с помощью пакета для конечно-элементного анализа Ansys 19.3. Решалась задача определения напряженно-деформированного состояния протеза и его составных частей – имплантатов и непосредственно каркаса – балки. По полученным значениям напряжений делался вывод о состоянии металлических конструкций при циклическом силовом воздействии. Геометрическая модель представлена нижней челюстью, включающей компактный и губчатый слои, мостовидной конструкцией с двумя имплантатами, ввернутыми в резьбу губчатого слоя, и зубами, закрепленными на имплантационной конструкции. Для ее получения использованы результаты компьютерной конусно-лучевой томограммы реального пациента. Конечно-элементная модель состоит из 383 507 тетраэдральных элементов второго порядка и 619 339 узлов. Составные части соединены между собой контактными элементами типа Bonded, имитирующими жесткое соединение без проскальзывания.
- 30 September 2023
- Published by PNRPU Publishing House in Российский журнал биомеханики
- Vol. 27 (3) , 24-35
Трехмерный конечно-элементный анализ влияния утраты дентального имплантата на распределение напряжения в имплантационном протезе нижней челюсти.
Имплантационный протез может иметь всего три опорных имплантата, и утрата одного из них может повлечь за собой потерю всей конструкции. Каркасом конструкции Trefoil является стандартная балка из высокопрочного титана. При циклическом нагружении металлов и металлических конструкций возникает эффект, уменьшающий прочностные характеристики – усталость. Предел усталости – значение напряжений, ниже которых разрушить конструкцию циклической нагрузкой невозможно. Целью работы является выбор тактики ведения пациента с утратой дистального имплантата и ее обоснование на основании результатов трехмерного конечно-элементного анализа влияния утраты одного дентального имплантата на биомеханику имплантационного протеза нижней челюсти с тремя опорами. Моделирование нагружения мостовидного протеза осуществлялось с помощью пакета для конечно-элементного анализа Ansys 19.3. Решалась задача определения напряженно-деформированного состояния протеза и его составных частей – имплантатов и непосредственно каркаса – балки. По полученным значениям напряжений делался вывод о состоянии металлических конструкций при циклическом силовом воздействии. Геометрическая модель представлена нижней челюстью, включающей компактный и губчатый слои, мостовидной конструкцией с двумя имплантатами, ввернутыми в резьбу губчатого слоя, и зубами, закрепленными на имплантационной конструкции. Для ее получения использованы результаты компьютерной конусно-лучевой томограммы реального пациента. Конечно-элементная модель состоит из 383 507 тетраэдральных элементов второго порядка и 619 339 узлов. Составные части соединены между собой контактными элементами типа Bonded, имитирующими жесткое соединение без проскальзывания.
- 30 September 2023
- Published by PNRPU Publishing House in Russian Journal of Biomechanics
- Vol. 27 (3) , 18-26
3D finite element analysis of the dental implant loss effect on the stress distribution in the mandibular implant-supported prosthesis
An implant-supported prosthesis may have as few as three supporting implants, and the loss of one of them may lead to the loss of the entire structure. The framework of the Trefoil design is a standard bar made of high-strength titanium. Cyclic loading of metals and metal structures brings about the effect reducing the strength characteristics and known as fatigue. Fatigue limit is the value of stress below which the cyclic loading can-not destroy the structure. The aim of the work is to determine the treatment tactics for a patient having lost a distal implant and justify it according to the results of a three-dimensional finite element analysis of the effect of one dental implant loss on the biome-chanics of a mandibular implant-supported prosthesis with three supports. Bridge loading modeling was carried out with the Ansys 19.3 finite element analysis package and thus the stress-strain condition of the prosthesis and its components, im-plants and the frame itself, namely the bar, were determined. The stress values obtained allowed to draw the conclusion about the condition of metal structures under cyclic load-ing. The geometric model represents the mandible, including the compact and spongy bone layers, a bridge structure with two implants screwed into the spongy layer, and arti-ficial teeth attached to the implant structure. The model was created with the use of a real patient’s computerized cone-beam tomogram (CBCT) findings. The finite element model consists of 383507 second-order tetrahedral elements and 619339 nodes. The compo-nents are interconnected by contact elements of the "bonded" type, imitating a rigid con-nection without slipping. With 220 MPa being the fatigue limit for the loaded titanium implant construction, it was concluded that extended prosthesis construction can withstand an unlimited number of loading cycles at 100 N loading with the maximum stress of 154 MPa occurring in the left part of the jaw. The clinician’s tactics was determined for the potential loss of function or removal of one of the three Trefoil supporting implants: the prosthesis must not be removed until reimplantation.
- 30 September 2023
- Published by PNRPU Publishing House in Russian Journal of Biomechanics
- Vol. 27 (3) , 18-26
3D finite element analysis of the dental implant loss effect on the stress distribution in the mandibular implant-supported prosthesis
An implant-supported prosthesis may have as few as three supporting implants, and the loss of one of them may lead to the loss of the entire structure. The framework of the Trefoil design is a standard bar made of high-strength titanium. Cyclic loading of metals and metal structures brings about the effect reducing the strength characteristics and known as fatigue. Fatigue limit is the value of stress below which the cyclic loading can-not destroy the structure. The aim of the work is to determine the treatment tactics for a patient having lost a distal implant and justify it according to the results of a three-dimensional finite element analysis of the effect of one dental implant loss on the biome-chanics of a mandibular implant-supported prosthesis with three supports. Bridge loading modeling was carried out with the Ansys 19.3 finite element analysis package and thus the stress-strain condition of the prosthesis and its components, im-plants and the frame itself, namely the bar, were determined. The stress values obtained allowed to draw the conclusion about the condition of metal structures under cyclic load-ing. The geometric model represents the mandible, including the compact and spongy bone layers, a bridge structure with two implants screwed into the spongy layer, and arti-ficial teeth attached to the implant structure. The model was created with the use of a real patient’s computerized cone-beam tomogram (CBCT) findings. The finite element model consists of 383507 second-order tetrahedral elements and 619339 nodes. The compo-nents are interconnected by contact elements of the "bonded" type, imitating a rigid con-nection without slipping. With 220 MPa being the fatigue limit for the loaded titanium implant construction, it was concluded that extended prosthesis construction can withstand an unlimited number of loading cycles at 100 N loading with the maximum stress of 154 MPa occurring in the left part of the jaw. The clinician’s tactics was determined for the potential loss of function or removal of one of the three Trefoil supporting implants: the prosthesis must not be removed until reimplantation.
- 21 June 2023
- Published by Media Sphere Publishing Group in Russian Journal of Stomatology
- Vol. 16 (2)
Comparative analysis of stress-strain state of tissues of multi-root teeth restored by root pin tabs made of zirconium dioxide and cobalt-chromium alloy
Goal. Determination of optimal designs of root pin inlays of multi-root teeth depending on the shape of the structure of the roots and the material of the orthopedic structure, taking into account the analysis of stress-strain states using mathematical models. Material and methods. 84 units of 3D models of the teeth of the upper and lower jaw chewing group with the most typical structure of the roots restored by root pin tabs made of cobalt chromium alloy (CCC) and zirconium dioxide have been developed. Results. Calculation of the main stresses arising in the tissues of teeth restored by root pin tabs under the action of chewing load at an angle 0°, 15°, 30°, 45° to the axis of the tooth showed that the nature of the stress distribution largely depends not on the shape of the structure of the roots of the teeth, but on the quality of modeling of the unloading area, as well as the number and length of the pin parts of the root pin tabs.
- 21 June 2023
- Published by Media Sphere Publishing Group in Russian Journal of Stomatology
- Vol. 16 (2)
Comparative analysis of stress-strain state of tissues of multi-root teeth restored by root pin tabs made of zirconium dioxide and cobalt-chromium alloy
Goal. Determination of optimal designs of root pin inlays of multi-root teeth depending on the shape of the structure of the roots and the material of the orthopedic structure, taking into account the analysis of stress-strain states using mathematical models. Material and methods. 84 units of 3D models of the teeth of the upper and lower jaw chewing group with the most typical structure of the roots restored by root pin tabs made of cobalt chromium alloy (CCC) and zirconium dioxide have been developed. Results. Calculation of the main stresses arising in the tissues of teeth restored by root pin tabs under the action of chewing load at an angle 0°, 15°, 30°, 45° to the axis of the tooth showed that the nature of the stress distribution largely depends not on the shape of the structure of the roots of the teeth, but on the quality of modeling of the unloading area, as well as the number and length of the pin parts of the root pin tabs.
- 1 January 2022
- Published by Media Sphere Publishing Group in Stomatologiya
- Vol. 101 (6) , 28-34
Experimental design of the lower jaw functional loading for implant-supported restoration in unfavorable clinical conditions
ЦЕЛЬ ИССЛЕДОВАНИЯ Повышение эффективности распределения нагрузки на кость нижней челюсти при протезировании с опорой на малое количество имплантатов. МАТЕРИАЛ И МЕТОДЫ Геометрическая модель создана с использованием результатов компьютерной конусно-лучевой томограммы реального пациента. Перевод формата DICOM в STL выполнен в программе Mimics Medical 21, в ней же проводилось конструирование авторского шинирующего устройства для имплантата. Реальные толщины компактного и губчатого слоев кости пациента были измерены с использованием программы Romexis ver. 4.5.1. Сканирование искусственного зубного ряда аппаратом iTero Element 2 Version 1.7 с получением объекта в формате STL. Моделирование выполнено в пакете для конечно-элементного анализа Ansys 19.3. При расчете использовались тетраэдральные элементы второго порядка. Элементы конструкции соединены в модели жестким контактом типа Bonded. Анализ полученных результатов проводился с использованием статистической программы SPSS 24. РЕЗУЛЬТАТЫ Создана конечно-элементная модель для экспериментального моделирования нагрузки на нижнюю челюсть при немедленном протезировании конструкцией с малым числом искусственных опор в сочетании с устройством для стабилизации имплантата в неблагоприятных клинических условиях. Показано, что разработанная конечно-элементная модель учитывает специфику биомеханики протеза с малым числом опор. При расчете вся модель закреплена за ветви нижней челюсти у основания ее отростков и нагружена силой 500 Н, распределенной по зубам. Значения максимальных напряжений составили 51,8 Мпа для компактного слоя и 245 Мпа — для титановых элементов. Исходное авторское шинирующее устройство снижает напряжение на 30%, а добавление горизонтальных подкрепляющих элементов позволяет снизить напряжения еще на 31%. ЗАКЛЮЧЕНИЕ Создана эффективная персонифицированная геометрическая и конечно-элементная модель для расчетов распределения функциональной нагрузки на полный несъемный протез большой протяженности с малым числом искусственных опор.
- 1 January 2022
- Published by Media Sphere Publishing Group in Stomatologiya
- Vol. 101 (6) , 28-34
Experimental design of the lower jaw functional loading for implant-supported restoration in unfavorable clinical conditions
ЦЕЛЬ ИССЛЕДОВАНИЯ Повышение эффективности распределения нагрузки на кость нижней челюсти при протезировании с опорой на малое количество имплантатов. МАТЕРИАЛ И МЕТОДЫ Геометрическая модель создана с использованием результатов компьютерной конусно-лучевой томограммы реального пациента. Перевод формата DICOM в STL выполнен в программе Mimics Medical 21, в ней же проводилось конструирование авторского шинирующего устройства для имплантата. Реальные толщины компактного и губчатого слоев кости пациента были измерены с использованием программы Romexis ver. 4.5.1. Сканирование искусственного зубного ряда аппаратом iTero Element 2 Version 1.7 с получением объекта в формате STL. Моделирование выполнено в пакете для конечно-элементного анализа Ansys 19.3. При расчете использовались тетраэдральные элементы второго порядка. Элементы конструкции соединены в модели жестким контактом типа Bonded. Анализ полученных результатов проводился с использованием статистической программы SPSS 24. РЕЗУЛЬТАТЫ Создана конечно-элементная модель для экспериментального моделирования нагрузки на нижнюю челюсть при немедленном протезировании конструкцией с малым числом искусственных опор в сочетании с устройством для стабилизации имплантата в неблагоприятных клинических условиях. Показано, что разработанная конечно-элементная модель учитывает специфику биомеханики протеза с малым числом опор. При расчете вся модель закреплена за ветви нижней челюсти у основания ее отростков и нагружена силой 500 Н, распределенной по зубам. Значения максимальных напряжений составили 51,8 Мпа для компактного слоя и 245 Мпа — для титановых элементов. Исходное авторское шинирующее устройство снижает напряжение на 30%, а добавление горизонтальных подкрепляющих элементов позволяет снизить напряжения еще на 31%. ЗАКЛЮЧЕНИЕ Создана эффективная персонифицированная геометрическая и конечно-элементная модель для расчетов распределения функциональной нагрузки на полный несъемный протез большой протяженности с малым числом искусственных опор.