Aman Tulegenovich Shakenov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aman Tulegenovich Shakenov has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Assem Utegenova
Institute of Energy and Mechanical Engineering Named after A. Burkitbayev, Department of Technological Machines and Gas Turbine Installations, Satbayev University, Almaty 050013, Kazakhstan
4 shared publications - Ainura Berikbolovna Orumbassarova
Institute of Energy and Mechanical Engineering Named after A. Burkitbayev, Department of Technological Machines and Gas Turbine Installations, Satbayev University, Almaty 050013, Kazakhstan
3 shared publications - Boris V. Malozyomov
Department of Electrotechnical Complexes, Novosibirsk State Technical University, 20, Karla Marksa Ave., 630073 Novosibirsk, Russia
3 shared publications - Ivan Nikitovich Stolpovskikh
Institute of Energy and Mechanical Engineering Named after A. Burkitbayev, Department of Technological Machines and Gas Turbine Installations, Satbayev University, Almaty 050013, Kazakhstan
3 shared publications - Ivan Stolpovskikh
Satpayev University
3 shared publications - Nikita Vladimirovich Martyushev
Department of Information Technology, Tomsk Polytechnic University, 634050 Tomsk, Russia
3 shared publications
Latest Publications
- Open Access
Infrastructure-Oriented Assessment of Energy Efficiency and Estimated CO2 Emissions at the Combustion Stage of a Diesel–LNG Dual-Fuel Mining Dump Truck Based on Field Telemetry Data
Haul-road condition can affect traction demand and diesel-to-LNG substitution in mining trucks. We evaluated a 140-t truck at the Ekibastuz coal mine using 180 registered cycles (88 diesel-only [DOM], 92 dual-fuel [DGB]), 24 road segments, 36 defect events and 30 matched fuel-mode pairs. Mean ECM-reported substitution was 30.61% across DGB cycles. In matched pairs, diesel use declined from 34.00 to 23.76 L/cycle, a mean saving of 10.24 L/cycle (95% CI 9.53–10.95); calculated combustion-stage CO2 declined by 7.10%. Total fuel energy, specific fuel-energy consumption and cycle time did not differ significantly (p > 0.30). Across Good-to-Poor road classes, engine load increased from 66.11% to 74.40% and substitution from 28.97% to 32.31%, while specific fuel-energy consumption increased from 5.91 to 6.72 MJ/(t·km). The load association persisted after temperature and wind adjustment and shift-clustered inference. Reference-state haul-road energy penalty was associated with rolling resistance and roughness, but remains dependent on a supplied reference input. The results distinguish diesel displacement from improved transport energy performance and are conditional on the cycle register. They do not establish causal road effects or a life-cycle climate benefit.
Open AccessInfrastructure-Oriented Assessment of Energy Efficiency and Estimated CO2 Emissions at the Combustion Stage of a Diesel–LNG Dual-Fuel Mining Dump Truck Based on Field Telemetry Data
Haul-road condition can affect traction demand and diesel-to-LNG substitution in mining trucks. We evaluated a 140-t truck at the Ekibastuz coal mine using 180 registered cycles (88 diesel-only [DOM], 92 dual-fuel [DGB]), 24 road segments, 36 defect events and 30 matched fuel-mode pairs. Mean ECM-reported substitution was 30.61% across DGB cycles. In matched pairs, diesel use declined from 34.00 to 23.76 L/cycle, a mean saving of 10.24 L/cycle (95% CI 9.53–10.95); calculated combustion-stage CO2 declined by 7.10%. Total fuel energy, specific fuel-energy consumption and cycle time did not differ significantly (p > 0.30). Across Good-to-Poor road classes, engine load increased from 66.11% to 74.40% and substitution from 28.97% to 32.31%, while specific fuel-energy consumption increased from 5.91 to 6.72 MJ/(t·km). The load association persisted after temperature and wind adjustment and shift-clustered inference. Reference-state haul-road energy penalty was associated with rolling resistance and roughness, but remains dependent on a supplied reference input. The results distinguish diesel displacement from improved transport energy performance and are conditional on the cycle register. They do not establish causal road effects or a life-cycle climate benefit.
- Open Access
- 4 August 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (15) , 7773
Quasi-Experimental Field Assessment of Haul-Road Maintenance Effects on Fuel Consumption, Cycle Time and Mechanical Loading of Open-Pit Dump Trucks
Haul-road condition in open-pit mining affects fuel consumption, transport-cycle throughput and dump-truck mechanical loading. This study conducted a quasi-experimental field assessment of local maintenance effects on severely degraded road segments. The full cycle register contained 32,000 entries, of which 30,808 passed quality control and were used for background engineering characterization. The primary difference-in-differences (DiD) analysis used 2634 matched-control cycle–focal-segment observations, while 72,000 one-second telemetry records formed a separate 20 h dynamic validation subset. Relative to matched-control dynamics, maintenance increased RCI by 3.26 points and reduced IRI by 6.24 m/km, the apparent rolling-resistance descriptor by 2.71 percentage points and rut depth by 41.2 mm. Regression-adjusted effects were −10.6 L/cycle for fuel, −0.78 min for cycle time, +10.7 km/h for segment speed, −0.351 g for vibration RMS and −78.2 MPa-eq. for the suspension-stress proxy. A 14-day lead-placebo/event-time diagnostic found no detectable pre-intervention divergence, and non-negative cohort-weighted group-time ATT estimates closely matched the TWFE results. The coefficients are interpreted as site-specific local intervention-window effects rather than annual fleet-wide constants.
- 4 August 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (15) , 7773
Open AccessQuasi-Experimental Field Assessment of Haul-Road Maintenance Effects on Fuel Consumption, Cycle Time and Mechanical Loading of Open-Pit Dump Trucks
Haul-road condition in open-pit mining affects fuel consumption, transport-cycle throughput and dump-truck mechanical loading. This study conducted a quasi-experimental field assessment of local maintenance effects on severely degraded road segments. The full cycle register contained 32,000 entries, of which 30,808 passed quality control and were used for background engineering characterization. The primary difference-in-differences (DiD) analysis used 2634 matched-control cycle–focal-segment observations, while 72,000 one-second telemetry records formed a separate 20 h dynamic validation subset. Relative to matched-control dynamics, maintenance increased RCI by 3.26 points and reduced IRI by 6.24 m/km, the apparent rolling-resistance descriptor by 2.71 percentage points and rut depth by 41.2 mm. Regression-adjusted effects were −10.6 L/cycle for fuel, −0.78 min for cycle time, +10.7 km/h for segment speed, −0.351 g for vibration RMS and −78.2 MPa-eq. for the suspension-stress proxy. A 14-day lead-placebo/event-time diagnostic found no detectable pre-intervention divergence, and non-negative cohort-weighted group-time ATT estimates closely matched the TWFE results. The coefficients are interpreted as site-specific local intervention-window effects rather than annual fleet-wide constants.
- Open Access
Field-Validated Multisensor Assessment of Haul-Road Degradation and Its Association with Fuel-Use Proxy Burden, Dynamic Response, and Transport-Cycle Stability in Open-Pit Mining
The performance of haul trucks in open-pit mining is strongly affected by haul-road geometry, surface condition, rolling resistance, and operational traffic regimes. However, existing studies often consider road-surface mapping, vehicle dynamic response, and onboard telemetry as separate information streams, which limits the reproducible assessment of how road-related factors are associated with VIMS-derived fuel-use proxy burden, mechanical dynamic response, and transport-cycle instability. This study proposes a field-based, segment-level multisensor framework that integrates unmanned aerial vehicle/light detection and ranging (UAV/LiDAR) road-surface reconstruction, global positioning system/inertial measurement unit (GPS/IMU) trajectory and vibration data, and Caterpillar Vial Information Management System (VIMS) telemetry into a unified spatiotemporal analytical dataset. The methodological contribution consists in the synchronization of heterogeneous data sources at the road-segment level, the calculation of interpretable road-condition and vehicle-response indicators, and the statistical assessment of road-related effects while explicitly accounting for confounding factors such as longitudinal grade, payload state, speed regime, truck class, and operational variability. Unlike studies that use LiDAR mapping, vibration monitoring, or onboard telemetry as separate diagnostic channels, the proposed approach introduces a segment-level analytical framework in which road morphology, truck response, and operational penalties are aligned within the same spatial unit, interpreted under confounder-aware conditions, and verified through repeat-pass reproducibility and robustness checks. The framework was tested on haul roads around the Ekibastuz open-pit coal mine. The field analysis identifies road segments where degraded surface morphology, increased waviness, unfavorable longitudinal profile, and higher rolling resistance coincide with increased mechanical dynamic response, VIMS-derived fuel-use proxy burden, braking instability, and travel-time variability. The results are interpreted as controlled field-supported associations rather than as isolated causal effects. The proposed maintenance ranking should therefore be regarded as a decision-support output, while the operational effectiveness of specific repair interventions requires future before–after validation.
Open AccessField-Validated Multisensor Assessment of Haul-Road Degradation and Its Association with Fuel-Use Proxy Burden, Dynamic Response, and Transport-Cycle Stability in Open-Pit Mining
The performance of haul trucks in open-pit mining is strongly affected by haul-road geometry, surface condition, rolling resistance, and operational traffic regimes. However, existing studies often consider road-surface mapping, vehicle dynamic response, and onboard telemetry as separate information streams, which limits the reproducible assessment of how road-related factors are associated with VIMS-derived fuel-use proxy burden, mechanical dynamic response, and transport-cycle instability. This study proposes a field-based, segment-level multisensor framework that integrates unmanned aerial vehicle/light detection and ranging (UAV/LiDAR) road-surface reconstruction, global positioning system/inertial measurement unit (GPS/IMU) trajectory and vibration data, and Caterpillar Vial Information Management System (VIMS) telemetry into a unified spatiotemporal analytical dataset. The methodological contribution consists in the synchronization of heterogeneous data sources at the road-segment level, the calculation of interpretable road-condition and vehicle-response indicators, and the statistical assessment of road-related effects while explicitly accounting for confounding factors such as longitudinal grade, payload state, speed regime, truck class, and operational variability. Unlike studies that use LiDAR mapping, vibration monitoring, or onboard telemetry as separate diagnostic channels, the proposed approach introduces a segment-level analytical framework in which road morphology, truck response, and operational penalties are aligned within the same spatial unit, interpreted under confounder-aware conditions, and verified through repeat-pass reproducibility and robustness checks. The framework was tested on haul roads around the Ekibastuz open-pit coal mine. The field analysis identifies road segments where degraded surface morphology, increased waviness, unfavorable longitudinal profile, and higher rolling resistance coincide with increased mechanical dynamic response, VIMS-derived fuel-use proxy burden, braking instability, and travel-time variability. The results are interpreted as controlled field-supported associations rather than as isolated causal effects. The proposed maintenance ranking should therefore be regarded as a decision-support output, while the operational effectiveness of specific repair interventions requires future before–after validation.
- Open Access
- 2 June 2026
- Published by Springer Nature in Geomechanics and Geophysics for Geo-Energy and Geo-Resources
- Vol. 12 (1)
Methods and applications of digital monitoring for mine haul road assessment
Transportation of rock mass is the main cost factor in open-pit mining, covering both the maintenance of mine haul roads and the operation of dump trucks. The high importance of optimizing the operation of mine transport is confirmed by the leading share of its costs in the total cost of mineral extraction. A relevant area of optimization is the development and implementation of digital technologies for processing data on the state of mine haul roads. The solution to these issues should be based on the results of research and development work on collecting and processing information on the operational and technical condition of dump trucks and mine roads. This study simultaneously tests three different modern digital monitoring methods, such as: unmanned aerial vehicle (UAV); vital information management system (VIMS) and GNSS-based data acquisition system (Racelogic VBOX), which allow experimental measurements of mine dump truck operating parameters both within the framework of special single experiments and in term of long-term monitoring measurements. The article presents data from experimental measurements to establish the condition of two sections of mine haul roads at the Vostochny open pit mine, Ekibastuz coal deposit. The study assessed the impact of mine road defects on the operating parameters of 130-ton dump trucks of the CAT 785 from Caterpillar, including recording the range of loads on the metal structures of dump trucks during their movement from road defects that exceed the regulated values of the manufacturers. Recommendations are presented to improve the efficiency of operation of mine haul roads.
- 2 June 2026
- Published by Springer Nature in Geomechanics and Geophysics for Geo-Energy and Geo-Resources
- Vol. 12 (1)
Open AccessMethods and applications of digital monitoring for mine haul road assessment
Transportation of rock mass is the main cost factor in open-pit mining, covering both the maintenance of mine haul roads and the operation of dump trucks. The high importance of optimizing the operation of mine transport is confirmed by the leading share of its costs in the total cost of mineral extraction. A relevant area of optimization is the development and implementation of digital technologies for processing data on the state of mine haul roads. The solution to these issues should be based on the results of research and development work on collecting and processing information on the operational and technical condition of dump trucks and mine roads. This study simultaneously tests three different modern digital monitoring methods, such as: unmanned aerial vehicle (UAV); vital information management system (VIMS) and GNSS-based data acquisition system (Racelogic VBOX), which allow experimental measurements of mine dump truck operating parameters both within the framework of special single experiments and in term of long-term monitoring measurements. The article presents data from experimental measurements to establish the condition of two sections of mine haul roads at the Vostochny open pit mine, Ekibastuz coal deposit. The study assessed the impact of mine road defects on the operating parameters of 130-ton dump trucks of the CAT 785 from Caterpillar, including recording the range of loads on the metal structures of dump trucks during their movement from road defects that exceed the regulated values of the manufacturers. Recommendations are presented to improve the efficiency of operation of mine haul roads.
- 13 October 2023
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 9(221),p. 49-54
Energy potential of high altitude mines in Central Asia
Зерттеудің негізгі мақсаты – Орта Азиядағы тау-кен жұмыстарында алтын кенін тасымалдаудың жаңа баламалы әдісін пайдалануды қарастыру және негіздеу. Зерттеудің жаңалығы – Қырғызстандағы кендеріның әлеуетті гравитациялық энергиясына алдын ала бағалау, жүк тиеу және төгу пунктінің GPS координаттарын орнында алу және көміртегі шығарындыларын азайту мақсатында кенді тасымалдаудың сәйкес технологияларын қарастыру. Алдыңғы зерттеулердегі әуе арқан жолының ерекше энергия тұтыну формуласы және қалпына келтіретін арқан жол жүйесі зерттеуде қарастырылады және пайдаланылады. Отын ұяшықтары бар энергияны қалпына келтіретін әуе арқан жүйесі Орта Азиядағы жоғары биіктікте орналасқан кендер үшін стратегиялық тұрғыдан ұзақ мерзімді таңдаулы шешім болуы мүмкін Consider and justify the use of a new alternative method of transporting ore at high-altitude mining in Central Asia as the main goal of the study. The novelty of the study lies in the preliminary assessment of mines in Kyrgyzstan for potential gravitational energy by taking GPS coordinates of loading and unloading points on site and considering appropriate technologies for transporting ore in order to reduce carbon dioxide emissions. The aerial ropeway specific energy consumption formula and the areal ropeway energy recovery system from previous studies are reviewed and used in the study a fuel cell energy recovery aerial ropeway could be a strategic long-term solution of choice for high-altitude mines in Central Asia Рассмотрено и обосновано использование нового альтернативного способа транспортировки руды на высотных горнодобывающих предприятиях в Центральной Азии в качестве основной цели исследования. Новизна исследования заключается в предварительной оценке рудников в Кыргызстане на предмет потенциальной гравитационной энергии путем снятия GPS-координат точек погрузки и разгрузки на месте и рассмотрения соответствующих технологий транспортировки руды с целью снижения выбросов углекислого газа. Формула удельного энергопотребления подвесной канатной дороги и система рекуперации энергии канатной дорогой из предыдущих исследований рассматриваются и используются в исследовании. Подвесная канатная дорога с рекуперацией энергии с топливными элементами может стать стратегически долгосрочным предпочтительным решением для рудников в Центральной Азии, расположенных на большой высоте
- 13 October 2023
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 9(221),p. 49-54
Energy potential of high altitude mines in Central Asia
Зерттеудің негізгі мақсаты – Орта Азиядағы тау-кен жұмыстарында алтын кенін тасымалдаудың жаңа баламалы әдісін пайдалануды қарастыру және негіздеу. Зерттеудің жаңалығы – Қырғызстандағы кендеріның әлеуетті гравитациялық энергиясына алдын ала бағалау, жүк тиеу және төгу пунктінің GPS координаттарын орнында алу және көміртегі шығарындыларын азайту мақсатында кенді тасымалдаудың сәйкес технологияларын қарастыру. Алдыңғы зерттеулердегі әуе арқан жолының ерекше энергия тұтыну формуласы және қалпына келтіретін арқан жол жүйесі зерттеуде қарастырылады және пайдаланылады. Отын ұяшықтары бар энергияны қалпына келтіретін әуе арқан жүйесі Орта Азиядағы жоғары биіктікте орналасқан кендер үшін стратегиялық тұрғыдан ұзақ мерзімді таңдаулы шешім болуы мүмкін Consider and justify the use of a new alternative method of transporting ore at high-altitude mining in Central Asia as the main goal of the study. The novelty of the study lies in the preliminary assessment of mines in Kyrgyzstan for potential gravitational energy by taking GPS coordinates of loading and unloading points on site and considering appropriate technologies for transporting ore in order to reduce carbon dioxide emissions. The aerial ropeway specific energy consumption formula and the areal ropeway energy recovery system from previous studies are reviewed and used in the study a fuel cell energy recovery aerial ropeway could be a strategic long-term solution of choice for high-altitude mines in Central Asia Рассмотрено и обосновано использование нового альтернативного способа транспортировки руды на высотных горнодобывающих предприятиях в Центральной Азии в качестве основной цели исследования. Новизна исследования заключается в предварительной оценке рудников в Кыргызстане на предмет потенциальной гравитационной энергии путем снятия GPS-координат точек погрузки и разгрузки на месте и рассмотрения соответствующих технологий транспортировки руды с целью снижения выбросов углекислого газа. Формула удельного энергопотребления подвесной канатной дороги и система рекуперации энергии канатной дорогой из предыдущих исследований рассматриваются и используются в исследовании. Подвесная канатная дорога с рекуперацией энергии с топливными элементами может стать стратегически долгосрочным предпочтительным решением для рудников в Центральной Азии, расположенных на большой высоте
- 26 April 2023
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 3(215),p. 44-49
Качар кені жолында троллей тасымалдау жүйусінің қолдану модельдеуі
Transportation costs in open pit mining may take 50 to 70% of overall open pit mining cost. Diesel fuel consumption takes more than 25% of owning and operating costs of large mining haul trucks and represents about 50% of carbon emissions at open pit sites. Modern software uses built-in characteristics of machine as rimpull and breaking performance, fuel, and electricity consumption rates. Computer simulation of CAT 794AC with trolley assist on conditions of Kachar mine 3068-meter haul road with 1100-meter trolley line section demonstrated 22% fuel consumption reduction and 10,9% higher production compare with conventional CAT 794AC. Study shown possible future efficiencies and practical recommendations for trolley assist application. During the study the real haul road condition’s data taken from mine site and used for simulation of future operational performance indicators. Key words: mining hauling truck; mine haul road; trolley assist; carbon emission, fuel efficiency, computer simulation, hydraulic front shovel, cost analyses, operator efficiency, lithium battery Тау-кен ашық әдіспен өндіруге арналған тасымалдау шығындары, әдетте, ашық әдіспен өндірудің жалпы шығындарының 50-ден 70%-ға дейін болады. Дизельді отынды тұтыну ірі тау-кен жүк көліктерін иелену және пайдалану шығындарының 25%-дан астамын құрайды және карьерлер- ден шығатын көміртегі шығарындыларының шамамен 50%-ын құрайды. Қазiргі замангі компьтерлік шешімдер машинаның кіріктірілген сипаттама- ларын пайдаланады, мысалы, тарту және тежеу өнімділігі, отын мен электр энергиясын тұтыну. Компьтерлік симуляция 1100 м троллейбус желісі бар 3068 метрлік көлік жолының Качар кеніның ортасында троллей жүйесі бар CAT 794AC үлгісінің симуляциясы кәдімгі CAT 794AC-пен салыстырғанда отын шығынының 22%-ға төмендеуін және өнімділіктің 10,9%-ға артқанын көрсетті. Зерттеу болашақта мүмкін болатын тиімділікті және троллей тарту жүйесін пайдалану бойынша практикалық ұсыныстарды көрсетті. Зеріттеуде карьердер тасымалдауға арналған нақты жол жағдайлары пайдаланылды Транспортные расходы при добыче открытым способом могут составлять от 50% до 70% от общих затрат на добычу. Потребление дизельного топлива составляет более 25% расходов на владение и эксплуатацию карьерных самосвалов и составляет около 50% выбросов углерода на карьерах. Современные программные решения используют встроенные характеристики машины, такие как тяговое усилие и тормозные характеристики, расход топлива и электроэнергии. Программное моделирование эксплуатации самосвала CAT 794AC с системой троллейной тяги в условиях Качар- ского рудника 3068-метровой технологической дороги с 1100-метровым участком троллейной линией продемонстрировало снижение расхода топлива на 22% и повышение производительности на 10,9% по сравнению с CAT 794AC в обычном исполнении. Исследование показало возможную эффектив- ность в будущем и практические рекомендации по применению системы троллейной тяги
- 26 April 2023
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 3(215),p. 44-49
Качар кені жолында троллей тасымалдау жүйусінің қолдану модельдеуі
Transportation costs in open pit mining may take 50 to 70% of overall open pit mining cost. Diesel fuel consumption takes more than 25% of owning and operating costs of large mining haul trucks and represents about 50% of carbon emissions at open pit sites. Modern software uses built-in characteristics of machine as rimpull and breaking performance, fuel, and electricity consumption rates. Computer simulation of CAT 794AC with trolley assist on conditions of Kachar mine 3068-meter haul road with 1100-meter trolley line section demonstrated 22% fuel consumption reduction and 10,9% higher production compare with conventional CAT 794AC. Study shown possible future efficiencies and practical recommendations for trolley assist application. During the study the real haul road condition’s data taken from mine site and used for simulation of future operational performance indicators. Key words: mining hauling truck; mine haul road; trolley assist; carbon emission, fuel efficiency, computer simulation, hydraulic front shovel, cost analyses, operator efficiency, lithium battery Тау-кен ашық әдіспен өндіруге арналған тасымалдау шығындары, әдетте, ашық әдіспен өндірудің жалпы шығындарының 50-ден 70%-ға дейін болады. Дизельді отынды тұтыну ірі тау-кен жүк көліктерін иелену және пайдалану шығындарының 25%-дан астамын құрайды және карьерлер- ден шығатын көміртегі шығарындыларының шамамен 50%-ын құрайды. Қазiргі замангі компьтерлік шешімдер машинаның кіріктірілген сипаттама- ларын пайдаланады, мысалы, тарту және тежеу өнімділігі, отын мен электр энергиясын тұтыну. Компьтерлік симуляция 1100 м троллейбус желісі бар 3068 метрлік көлік жолының Качар кеніның ортасында троллей жүйесі бар CAT 794AC үлгісінің симуляциясы кәдімгі CAT 794AC-пен салыстырғанда отын шығынының 22%-ға төмендеуін және өнімділіктің 10,9%-ға артқанын көрсетті. Зерттеу болашақта мүмкін болатын тиімділікті және троллей тарту жүйесін пайдалану бойынша практикалық ұсыныстарды көрсетті. Зеріттеуде карьердер тасымалдауға арналған нақты жол жағдайлары пайдаланылды Транспортные расходы при добыче открытым способом могут составлять от 50% до 70% от общих затрат на добычу. Потребление дизельного топлива составляет более 25% расходов на владение и эксплуатацию карьерных самосвалов и составляет около 50% выбросов углерода на карьерах. Современные программные решения используют встроенные характеристики машины, такие как тяговое усилие и тормозные характеристики, расход топлива и электроэнергии. Программное моделирование эксплуатации самосвала CAT 794AC с системой троллейной тяги в условиях Качар- ского рудника 3068-метровой технологической дороги с 1100-метровым участком троллейной линией продемонстрировало снижение расхода топлива на 22% и повышение производительности на 10,9% по сравнению с CAT 794AC в обычном исполнении. Исследование показало возможную эффектив- ность в будущем и практические рекомендации по применению системы троллейной тяги
- Open Access
- 1 January 2023
- Published by Satbayev University in Engineering Journal of Satbayev University
- Vol. 145 (4) , 32-35
Mining haul truck operation failure analysis
Estimated 45% of all mining equipment worldwide is mining haul trucks. More than 44 thousand mining haul trucks are in operation worldwide as per 2017 Mine Safety and Health Administration of USA reports and over 20% of accidents with fatalities on mining equipment happens with participation of mining haul trucks. Mining haul trucks are critical equipment for mining industry of Kazakhstan where 80% of mines are operated by open cast mining. To better understand haul trucks operation failures statistical method was used during this study. 8 training instructors were interviews who trained 1048 truck operators over 3 years at 5 mine sites. The analyses explore the context of the accidents with focus on initiating reasons, outcomes of accidents and possible preventive and mitigative controls. Overall, most accidents take place due to haul road condition, read design and operation decision making. Bow-tie diagram as a constructive risk management tool used in this study for visual presentation of links between hazards, initiating controls, preventive and mitigative controls, and outcomes. The results of the study suggest improving organizational control over operator trainings and mine haul road design and maintenance.
- 1 January 2023
- Published by Satbayev University in Engineering Journal of Satbayev University
- Vol. 145 (4) , 32-35
Open AccessMining haul truck operation failure analysis
Estimated 45% of all mining equipment worldwide is mining haul trucks. More than 44 thousand mining haul trucks are in operation worldwide as per 2017 Mine Safety and Health Administration of USA reports and over 20% of accidents with fatalities on mining equipment happens with participation of mining haul trucks. Mining haul trucks are critical equipment for mining industry of Kazakhstan where 80% of mines are operated by open cast mining. To better understand haul trucks operation failures statistical method was used during this study. 8 training instructors were interviews who trained 1048 truck operators over 3 years at 5 mine sites. The analyses explore the context of the accidents with focus on initiating reasons, outcomes of accidents and possible preventive and mitigative controls. Overall, most accidents take place due to haul road condition, read design and operation decision making. Bow-tie diagram as a constructive risk management tool used in this study for visual presentation of links between hazards, initiating controls, preventive and mitigative controls, and outcomes. The results of the study suggest improving organizational control over operator trainings and mine haul road design and maintenance.
- 25 December 2022
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 6,p. 25-29
Haul road condition impact on tire life of mining dump truck
New+Mining +https://doi.org/10.33271/nvngu/2022-6 +/jdownloads/pdf/2022/6/06_2022_Contents-en-GB.pdf
- 25 December 2022
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 6,p. 25-29
Haul road condition impact on tire life of mining dump truck
New+Mining +https://doi.org/10.33271/nvngu/2022-6 +/jdownloads/pdf/2022/6/06_2022_Contents-en-GB.pdf