Ahmet Ali Sertkaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ahmet Ali Sertkaya has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Anilcan Sarikaya
Selcuk Universitesi
2 shared publications - Cengiz Güler
DÜZCE ÜNİVERSİTESİ, ORMAN FAKÜLTESİ, ORMAN ENDÜSTRİSİ MÜHENDİSLİĞİ BÖLÜMÜ
2 shared publications - Eyüb Canli
Selcuk Universitesi
2 shared publications - Abdullah Çakan
Department of Mechanical Engineering, Konya Technical University, Selçuklu, Konya 42250, Türkiye
1 shared publication - Can Çalişkan
Selcuk University
1 shared publication Furkan Parlak
1 shared publication
Latest Publications
- Open Access
- 20 May 2024
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 39 (3) , 1917-1932
Badem kabuğu içerikli yonga levha üretimi ve ısıl iletkenliklerinin belirlenmesi
Badem meyvesi, tüketimi sürekli artan, ülkemiz için de öneme haiz, değerli bir tarım ürünüdür. Üç katmanından dıştaki insanlar tarafından tüketilmez ve başka endüstrilerde kullanılmaktadır. Kalan iki katman çekirdeği oluşturur. Çekirdeğin kabuğu ile içi neredeyse aynı ağırlığa sahiptir. İç kısım insanlar için değerli bir yemişken kabuk genellikle yakılarak, nadiren de öğütülerek kozmetik sektöründe veya filtrelerde kullanılmaktadır. Badem kabuğu gözenekli ve sert, lignoselülozik, yenilenebilir bir kaynaktır. Bu kaynağa sürdürülebilir, daha yüksek katma değer oluşturan, çevre etkisi daha düşük bir kullanım için yonga levha endüstrisi düşünülmüştür. Bu amaçla detaylı bir literatür taraması yapılmış ve akabinde badem kabuğu parçacıkları kullanılarak yonga levhalar üretilmiştir. Badem kabuğu parçacıklarının yonga levha içerisindeki ağırlıkça farklı oranları ile bir üretim seti oluşturulmuş, daha sonra levhaların yoğunluk değişiminin incelenebilmesi için farklı yoğunluklarda ikinci bir üretim yapılmıştır. Levhaların ısıl iletkenlikleri deneysel olarak belirlenmiştir. Levha yoğunluğu artışı ile ısıl iletkenlik değeri artmaktadır. Badem kabuğu oranı ise levha yoğunluklarına bağlı olarak farklı etkiler göstermektedir. Çalışmada en küçük ısıl iletkenlik değeri 0,07 W/m·K olarak elde edilirken en yüksek değer 0,19 W/m·K olarak bulunmuştur. Çalışma sabit sıcaklık farkı ile gerçekleştirilmesine rağmen sıcaklık değerlerindeki artışa bağlı olarak ısıl iletkenlik değeri artmaktadır. En düşük ısıl iletkenlik 0,6 g/cm3 ve %60 badem kabuğu katkılı levha için elde edilmiştir.
- 20 May 2024
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 39 (3) , 1917-1932
Open AccessBadem kabuğu içerikli yonga levha üretimi ve ısıl iletkenliklerinin belirlenmesi
Badem meyvesi, tüketimi sürekli artan, ülkemiz için de öneme haiz, değerli bir tarım ürünüdür. Üç katmanından dıştaki insanlar tarafından tüketilmez ve başka endüstrilerde kullanılmaktadır. Kalan iki katman çekirdeği oluşturur. Çekirdeğin kabuğu ile içi neredeyse aynı ağırlığa sahiptir. İç kısım insanlar için değerli bir yemişken kabuk genellikle yakılarak, nadiren de öğütülerek kozmetik sektöründe veya filtrelerde kullanılmaktadır. Badem kabuğu gözenekli ve sert, lignoselülozik, yenilenebilir bir kaynaktır. Bu kaynağa sürdürülebilir, daha yüksek katma değer oluşturan, çevre etkisi daha düşük bir kullanım için yonga levha endüstrisi düşünülmüştür. Bu amaçla detaylı bir literatür taraması yapılmış ve akabinde badem kabuğu parçacıkları kullanılarak yonga levhalar üretilmiştir. Badem kabuğu parçacıklarının yonga levha içerisindeki ağırlıkça farklı oranları ile bir üretim seti oluşturulmuş, daha sonra levhaların yoğunluk değişiminin incelenebilmesi için farklı yoğunluklarda ikinci bir üretim yapılmıştır. Levhaların ısıl iletkenlikleri deneysel olarak belirlenmiştir. Levha yoğunluğu artışı ile ısıl iletkenlik değeri artmaktadır. Badem kabuğu oranı ise levha yoğunluklarına bağlı olarak farklı etkiler göstermektedir. Çalışmada en küçük ısıl iletkenlik değeri 0,07 W/m·K olarak elde edilirken en yüksek değer 0,19 W/m·K olarak bulunmuştur. Çalışma sabit sıcaklık farkı ile gerçekleştirilmesine rağmen sıcaklık değerlerindeki artışa bağlı olarak ısıl iletkenlik değeri artmaktadır. En düşük ısıl iletkenlik 0,6 g/cm3 ve %60 badem kabuğu katkılı levha için elde edilmiştir.
- 11 May 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 431
Almond shell particle containing particleboard mechanical and physical properties
- 11 May 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 431
Almond shell particle containing particleboard mechanical and physical properties
- Open Access
- 16 December 2022
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 25 (4) , 1835-1845
Comparison of Real and Simulation Aerodynamic Coefficients for 155 mm Ammunition Using Open-Source Code SU2 Software
In this study, density, energy, pressure, temperature changes, and drag coefficients occurring during the trajectory of movement for a 155 mm ammunition shell were simulated with the computational flow dynamics software Stanford University Unstructured (SU2). Reynolds-Averaged Navier-Stokes (RANS) equations, which are operationally simplified variations of the Navier-Stokes (N-S) flow solver, were used in the simulations. The Reynolds number based on the velocity was between 1.65x107 to 6.5x107 according to the Mach (M) number between 0.7 to 2.8 in the present simulation. The drag coefficients from 0.7 M to 2.8 M were obtained separately for each Mach 0.3 increase. The Free Computer-Aided Design (FreeCAD) program was used for geometrical drawings of the ammunition, the Geometry Description, Meshing, Solving, and Post-Processing (GMSH) software for mesh operations, and the Shear Stress Transport (SST) turbulence model to create a compressible finite volume. As well, 0 degrees was used as the angle of attack. For estimation of the aerodynamic coefficient percentage changes obtained from the simulations, exponential equations with the highest validity based on the R2 value were created. In addition, the calculated drag coefficients were compared with the actual values and a good fit was observed between them.
- 16 December 2022
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 25 (4) , 1835-1845
Open AccessComparison of Real and Simulation Aerodynamic Coefficients for 155 mm Ammunition Using Open-Source Code SU2 Software
In this study, density, energy, pressure, temperature changes, and drag coefficients occurring during the trajectory of movement for a 155 mm ammunition shell were simulated with the computational flow dynamics software Stanford University Unstructured (SU2). Reynolds-Averaged Navier-Stokes (RANS) equations, which are operationally simplified variations of the Navier-Stokes (N-S) flow solver, were used in the simulations. The Reynolds number based on the velocity was between 1.65x107 to 6.5x107 according to the Mach (M) number between 0.7 to 2.8 in the present simulation. The drag coefficients from 0.7 M to 2.8 M were obtained separately for each Mach 0.3 increase. The Free Computer-Aided Design (FreeCAD) program was used for geometrical drawings of the ammunition, the Geometry Description, Meshing, Solving, and Post-Processing (GMSH) software for mesh operations, and the Shear Stress Transport (SST) turbulence model to create a compressible finite volume. As well, 0 degrees was used as the angle of attack. For estimation of the aerodynamic coefficient percentage changes obtained from the simulations, exponential equations with the highest validity based on the R2 value were created. In addition, the calculated drag coefficients were compared with the actual values and a good fit was observed between them.
- 30 June 2022
- Published by International Journal of Energy Applications and Technologies in International Journal of Energy Applications and Technologies
- Vol. 9 (2) , 38-44
Determining the design parameters for manufacturing a shell and tube heat exchanger with minimum cost using The Bees Algorithm
The shell and tube heat exchanger is one of the commonly used heat exchangers. Minimizing the cost required to manufacture these heat exchangers is one of the main objectives for designers and users. This study determined the necessary design parameters for a shell and tube heat exchanger to be manufactured with minimum cost using The Bees Algorithm (BA). These design parameters are the shell side inside diameter, the tube side outside diameter, and the baffle spaces. The system mathematical model is created to find the optimum values of these parameters, the necessary boundary conditions are determined, and an optimization study is carried out. The cost obtained by BA $ 11187.86 compared with GA $ 11190.17 and SPQ $ 18429.4 from the literature. It is observed that The Bees Algorithm (BA) gives successful results in the design of shell and tube heat exchangers.- 30 June 2022
- Published by International Journal of Energy Applications and Technologies in International Journal of Energy Applications and Technologies
- Vol. 9 (2) , 38-44
Determining the design parameters for manufacturing a shell and tube heat exchanger with minimum cost using The Bees Algorithm
The shell and tube heat exchanger is one of the commonly used heat exchangers. Minimizing the cost required to manufacture these heat exchangers is one of the main objectives for designers and users. This study determined the necessary design parameters for a shell and tube heat exchanger to be manufactured with minimum cost using The Bees Algorithm (BA). These design parameters are the shell side inside diameter, the tube side outside diameter, and the baffle spaces. The system mathematical model is created to find the optimum values of these parameters, the necessary boundary conditions are determined, and an optimization study is carried out. The cost obtained by BA $ 11187.86 compared with GA $ 11190.17 and SPQ $ 18429.4 from the literature. It is observed that The Bees Algorithm (BA) gives successful results in the design of shell and tube heat exchangers.