Александр Станиславович Милонов
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Александр Станиславович Милонов has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Undrakh L. Mishigdorzhiin
Hubei Digital Textile Equipment Key Laboratory, Wuhan Textile University, Wuhan 430073, China
5 shared publications - Stepan A. Lysykh
Institute of Physical Materials Science, Siberian Branch, Russian Academy of Sciences, Ulan-Ude, Russia
3 shared publications A. P. Semenov
2 shared publications- Alexander P. Semenov
Institute of Physical Materials Science, Siberian Branch, Russian Academy of Sciences, Ulan-Ude, Russia
2 shared publications D E Dasheev
Institute of Physical Materials Science SB RAS, 8 Sakhyanova Str., Ulan-Ude, The Republic of Buryatia, 670047, Russia
2 shared publicationsN N Smirnyagina
Institute of Physical Materials Science SB RAS, 8 Sakhyanova Str., Ulan-Ude, The Republic of Buryatia, 670047, Russia
2 shared publications
Latest Publications
- 1 December 2024
- Published by Pleiades Publishing Ltd in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
- Vol. 18 (S1) , S122-S126
Protective Coatings based on VB2 on the Surface of D2 die Steel Formed by an Electron Beam in a Vacuum
The paper presents the results of surface hardening of samples made of D2 die steel by complex alloying with preliminary application of a saturating mixture to the surface of the sample, followed by exposure to an electron beam. The morphology and structure of surface layers after electron beam treatment have been studied. Microhardness, elemental and phase compositions, as well as wear resistance in terms of mass loss depending on time were determined. Complex alloying of boron-containing components together with electron beam processing leads to the production of layers with improved physical and mechanical characteristics. The structure of the surface layer, its hardness, structural and phase composition are subject to change. It was found that the alloyed sample has wear resistance from 2.4 to 3.8 times higher than the sample in the original state.
- 1 December 2024
- Published by Pleiades Publishing Ltd in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
- Vol. 18 (S1) , S122-S126
Protective Coatings based on VB2 on the Surface of D2 die Steel Formed by an Electron Beam in a Vacuum
The paper presents the results of surface hardening of samples made of D2 die steel by complex alloying with preliminary application of a saturating mixture to the surface of the sample, followed by exposure to an electron beam. The morphology and structure of surface layers after electron beam treatment have been studied. Microhardness, elemental and phase compositions, as well as wear resistance in terms of mass loss depending on time were determined. Complex alloying of boron-containing components together with electron beam processing leads to the production of layers with improved physical and mechanical characteristics. The structure of the surface layer, its hardness, structural and phase composition are subject to change. It was found that the alloyed sample has wear resistance from 2.4 to 3.8 times higher than the sample in the original state.
- 1 October 2024
- Published by Pleiades Publishing Ltd in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
- Vol. 18 (5) , 1260-1264
Formation of a Protective Layer Based on Chromium Boride on the Surface of Kh12MF Steel Using Electron-Beam Treatment
The preparation of coating layers containing the borides Cr2B, Cr2B3, and FeB on Kh12MF steel using the electron-beam treatment of reacting coatings made of Cr2O3, amorphous boron, and carbon is considered. The influence of the treatment time on the structure, composition, and microhardness of the layers is investigated. The maximum microhardness of the layers is ~18.5 GPa. The studies allow one to conclude that electron-beam treatment can be used to strengthen cutting and other tools, which experience high temperature heating during operation, without a significant reduction in performance. It is known that, along with high hardness and wear resistance, boride layers also have a significant disadvantage: increased brittleness. The studies carried out show that the use of electronic heating allows a reduction in brittleness and increase in plasticity of the alloys. The layers after electron-beam boriding have a heterogeneous structure combining hard (brittle) and more plastic structural components.
- 1 October 2024
- Published by Pleiades Publishing Ltd in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
- Vol. 18 (5) , 1260-1264
Formation of a Protective Layer Based on Chromium Boride on the Surface of Kh12MF Steel Using Electron-Beam Treatment
The preparation of coating layers containing the borides Cr2B, Cr2B3, and FeB on Kh12MF steel using the electron-beam treatment of reacting coatings made of Cr2O3, amorphous boron, and carbon is considered. The influence of the treatment time on the structure, composition, and microhardness of the layers is investigated. The maximum microhardness of the layers is ~18.5 GPa. The studies allow one to conclude that electron-beam treatment can be used to strengthen cutting and other tools, which experience high temperature heating during operation, without a significant reduction in performance. It is known that, along with high hardness and wear resistance, boride layers also have a significant disadvantage: increased brittleness. The studies carried out show that the use of electronic heating allows a reduction in brittleness and increase in plasticity of the alloys. The layers after electron-beam boriding have a heterogeneous structure combining hard (brittle) and more plastic structural components.
- Open Access
- 25 March 2024
- Published by Siberian State Industrial University in Bulletin of the Siberian State Industrial University
- Vol. 1 (1) , 92-102
ELECTRON BEAM PROCESSING OF DIFFUSION BOROALUMINIZING LAYERSON THE SURFACE OF STEEL 5KHNM
The hardening of the surface of samples made of die steel 5KhNM by a combined method is considered, which consists of sequential thermal-chemical treatment (TCT) followed by modification of the resulting diffu-sion layer using pulsed electron beam processing using an electron source with a plasma cathode based on a low-pressure arc discharge. Electron beam processing was carried out in the SOLO experimental installation, which is included in the list of unique electrophysical installations in Russia. The results of local structural-phase transformation of diffusion boroaluminizing layers due to high-speed heating by an electron beam of millisecond duration are presented. A comparative analysis of the structure of the diffusion layer after thermal -chemical treatment and subsequent modification ofthe layer with a pulsed electron beam was carried out. Mi-crohardness was studied, and the phase state of the diffusion layer was assessed before and after electron beam exposure. Electron beam treatment (EBT) of the diffusion layer leads to an increase inmicro-hardness values, the maximum value of which reaches 1400 HV, and to a decrease in surface roughness values in the Raparam-eter (up to seven times). After electron beam treatment of the diffusion layer, the Fe2Bphase and intermetallic phases FeAl, Fe2AlCr, CrSi2are formed, which have high heat resistance, wear resistance and corrosion re-sistance. Рассмотрено упрочнение поверхности образцов из штамповой стали 5ХНМ комбинированным методом, заключающимся в последовательном проведении химико-термической обработки с последующей модификацией полученного диффузионного слоя с помощью импульсной электронно-пучковой обработки с использованием источника электронов с плазменным катодом на основе дугового разряда низкого давления. Электронно-пучковую обработку проводили в экспериментальной установке «СОЛО», входящей в перечень уникальных электрофизических установок России. Представлены результаты локальной структурно-фазовой трансформации диффузионных бороалитированныхслоев за счет скоростного нагрева электронным пучком миллисекундной длительности. Проведен сравнительный анализ строения диффузионного слоя после химико-термической обработки и последующей модификации слоя импульсным электронным пучком. Изучена микротвердость, проведена оценка фазового состояния диффузионного слоя до и после электронно-пучкового воздействия. Электронно-пучковая обработка диффузионного слоя приводит к повышению микротвердости, максимальное значений которой достигает 1400 HV, и к снижению шероховатости поверхности по параметру Ra(до семи раз). После электронно-пучковой обработки диффузионного слоя формируются фаза Fe2B, интерметалидные фазы FeAl, Fe2AlCr, CrSi2, обладающие высокой жаростойкостью, износостойкостью и коррозийной стойкостью.
- 25 March 2024
- Published by Siberian State Industrial University in Bulletin of the Siberian State Industrial University
- Vol. 1 (1) , 92-102
Open AccessELECTRON BEAM PROCESSING OF DIFFUSION BOROALUMINIZING LAYERSON THE SURFACE OF STEEL 5KHNM
The hardening of the surface of samples made of die steel 5KhNM by a combined method is considered, which consists of sequential thermal-chemical treatment (TCT) followed by modification of the resulting diffu-sion layer using pulsed electron beam processing using an electron source with a plasma cathode based on a low-pressure arc discharge. Electron beam processing was carried out in the SOLO experimental installation, which is included in the list of unique electrophysical installations in Russia. The results of local structural-phase transformation of diffusion boroaluminizing layers due to high-speed heating by an electron beam of millisecond duration are presented. A comparative analysis of the structure of the diffusion layer after thermal -chemical treatment and subsequent modification ofthe layer with a pulsed electron beam was carried out. Mi-crohardness was studied, and the phase state of the diffusion layer was assessed before and after electron beam exposure. Electron beam treatment (EBT) of the diffusion layer leads to an increase inmicro-hardness values, the maximum value of which reaches 1400 HV, and to a decrease in surface roughness values in the Raparam-eter (up to seven times). After electron beam treatment of the diffusion layer, the Fe2Bphase and intermetallic phases FeAl, Fe2AlCr, CrSi2are formed, which have high heat resistance, wear resistance and corrosion re-sistance. Рассмотрено упрочнение поверхности образцов из штамповой стали 5ХНМ комбинированным методом, заключающимся в последовательном проведении химико-термической обработки с последующей модификацией полученного диффузионного слоя с помощью импульсной электронно-пучковой обработки с использованием источника электронов с плазменным катодом на основе дугового разряда низкого давления. Электронно-пучковую обработку проводили в экспериментальной установке «СОЛО», входящей в перечень уникальных электрофизических установок России. Представлены результаты локальной структурно-фазовой трансформации диффузионных бороалитированныхслоев за счет скоростного нагрева электронным пучком миллисекундной длительности. Проведен сравнительный анализ строения диффузионного слоя после химико-термической обработки и последующей модификации слоя импульсным электронным пучком. Изучена микротвердость, проведена оценка фазового состояния диффузионного слоя до и после электронно-пучкового воздействия. Электронно-пучковая обработка диффузионного слоя приводит к повышению микротвердости, максимальное значений которой достигает 1400 HV, и к снижению шероховатости поверхности по параметру Ra(до семи раз). После электронно-пучковой обработки диффузионного слоя формируются фаза Fe2B, интерметалидные фазы FeAl, Fe2AlCr, CrSi2, обладающие высокой жаростойкостью, износостойкостью и коррозийной стойкостью.
- Open Access
- 1 January 2023
- Published by Buryat Scientific Center SB RAS
- p. 273-279
ELECTRON-BEAM MODIFICATION OF BORIDE DIFFUSION LAYERS ON THE SURFACE OF STEEL 45 AND U10
- 1 January 2023
- Published by Buryat Scientific Center SB RAS
- p. 273-279
Open AccessELECTRON-BEAM MODIFICATION OF BORIDE DIFFUSION LAYERS ON THE SURFACE OF STEEL 45 AND U10
- Open Access
- 26 December 2022
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 19 (4) , 546-553
ПОВЫШЕНИЕ ПЛАСТИЧНОСТИ БОРИДНОГО ПОКРЫТИЯ НА НИЗКОУГЛЕРОДИСТОЙ СТАЛИ
В работе представлены сравнительные исследования структуры, микротвердости, коэффициента диффузии и пластичности борированного и боромедненного слоев, полученных на низкоуглеродистой стали Ст3 за время выдержки 3, 4 и 5 ч при помощи разработанного совмещенного твердофазного метода с использованием высокотемпературного синтеза насыщающих элементов из окислов бора и медив процессе термической обработки (ТО), что приводит к интенсификации процесса легирования поверхности железоуглеродистых сплавов (ЖУС). При чистом борировании в процессе химической термообработки (ХТО) формирование покрытия происходит по классическому варианту с образованием слоя со структурой игольчатые кристаллиты, ориентированные от поверхности вглубь металла. После 5-ти часовой обработки формируется двухфазное покрытие из высшего борида FeB с микротвердостью 21-22 ГПа и расположенного под ним слоя низшего борида Fe2B с микротвердостью 18-19 ГПа. Толщина слоя высшего борида составляет до трети от общей протяженности борированного покрытия. Максимальная длинна игл для борирования составила 120 мкм, Структура боромедненного покрытия также имеет структуру игольчатых кристаллитов, но отличается более плотной упаковкой и большей длинной игл – до 200 мкм. При боромеднении устанавливает положительный градиент роста микротвердости от поверхности вглубь слоя с максимальной величиной 18-18,5 ГПа на расстоянии 10…20 % от поверхности от общей толщины покрытия. Коэффициент диффузии бора при наличии в грануле окиси меди увеличивается до 4-х раз, определенный расчетом и уравнениями, полученными при помощи программного обеспечения Excel. Величина хрупкости eпред для борирования составила 1,25-1,27, для боромеднения – 2,21-2,42, что оценивается баллами хрупкости: для борирования – 3, для боромеднения – 1. Наличие окиси меди в реакционной грануле способствует диффузии бора вглубь ЖУС с формированием фазы из низшего борида железа, что положительно сказывается на финишной обработке и эксплуатации обрабатываемых деталей.
- 26 December 2022
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 19 (4) , 546-553
Open AccessПОВЫШЕНИЕ ПЛАСТИЧНОСТИ БОРИДНОГО ПОКРЫТИЯ НА НИЗКОУГЛЕРОДИСТОЙ СТАЛИ
В работе представлены сравнительные исследования структуры, микротвердости, коэффициента диффузии и пластичности борированного и боромедненного слоев, полученных на низкоуглеродистой стали Ст3 за время выдержки 3, 4 и 5 ч при помощи разработанного совмещенного твердофазного метода с использованием высокотемпературного синтеза насыщающих элементов из окислов бора и медив процессе термической обработки (ТО), что приводит к интенсификации процесса легирования поверхности железоуглеродистых сплавов (ЖУС). При чистом борировании в процессе химической термообработки (ХТО) формирование покрытия происходит по классическому варианту с образованием слоя со структурой игольчатые кристаллиты, ориентированные от поверхности вглубь металла. После 5-ти часовой обработки формируется двухфазное покрытие из высшего борида FeB с микротвердостью 21-22 ГПа и расположенного под ним слоя низшего борида Fe2B с микротвердостью 18-19 ГПа. Толщина слоя высшего борида составляет до трети от общей протяженности борированного покрытия. Максимальная длинна игл для борирования составила 120 мкм, Структура боромедненного покрытия также имеет структуру игольчатых кристаллитов, но отличается более плотной упаковкой и большей длинной игл – до 200 мкм. При боромеднении устанавливает положительный градиент роста микротвердости от поверхности вглубь слоя с максимальной величиной 18-18,5 ГПа на расстоянии 10…20 % от поверхности от общей толщины покрытия. Коэффициент диффузии бора при наличии в грануле окиси меди увеличивается до 4-х раз, определенный расчетом и уравнениями, полученными при помощи программного обеспечения Excel. Величина хрупкости eпред для борирования составила 1,25-1,27, для боромеднения – 2,21-2,42, что оценивается баллами хрупкости: для борирования – 3, для боромеднения – 1. Наличие окиси меди в реакционной грануле способствует диффузии бора вглубь ЖУС с формированием фазы из низшего борида железа, что положительно сказывается на финишной обработке и эксплуатации обрабатываемых деталей.
- Open Access
- 7 May 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (5) , 90
Microstructure and Wear Resistance of Hot-Work Tool Steels after Electron Beam Surface Alloying with B4C and Al
(1) Background: Operational properties and durability of dies in different metal-forming processes significantly depend on their surface quality. Major die failures are related to surface damage due to heat checking cracks, wear, etc. Thereby, strengthening of the working surfaces of dies for hot bending, stamping, forging, and die casting processes is an urgent engineering challenge. Surface alloying with high-energy beams improves the properties of steel products. In these processes, the alloying powders and the treated surfaces can be remelted by electron beam within a short time while the bulk structure of the component remains unchanged, resulting in minimal distortion. The paper presents the results of the electron beam surface alloying (EBSA) of H21 and L6 tool steels with the treatment pastes containing boron carbide and aluminum powders. (2) Methods: Two types of pastes were used for surface alloying: a single-component (B4C) paste and a two-component (B4C+Al) one. The microstructure, microhardness, wear resistance, and elemental and phase composition of the layers obtained on steels were investigated. (3) Results: Four layers up to 0.4 mm thick were distinguished on the surface of the steels after the EBSA. Metallographic analysis showed coarse dendrite formation in the layers embedded in matrices of a eutectic or a solid solution. Microhardness of the steels after the two-component EBSA was higher than after B4C EBSA, which was related to a higher concentration of hard phases, such as iron borides and carbides. In addition, aluminum boride was revealed by the XRD analysis on L6 steel after B4C+Al EBSA. (4) Conclusions: Wear test indicated that the most resistant samples were H21 steel after single B4C EBSA and L6 steel after B4C+Al EBSA. Both samples contained carbon particles in the layer contributing to the high wear resistance as a lubricant. The conducted research is beneficial for mechanical engineering, automotive engineering, medical technology, aerospace engineering, and related industries, where coatings with high microhardness, wear resistance, and surface quality are demanded.
- 7 May 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (5) , 90
Open AccessMicrostructure and Wear Resistance of Hot-Work Tool Steels after Electron Beam Surface Alloying with B4C and Al
(1) Background: Operational properties and durability of dies in different metal-forming processes significantly depend on their surface quality. Major die failures are related to surface damage due to heat checking cracks, wear, etc. Thereby, strengthening of the working surfaces of dies for hot bending, stamping, forging, and die casting processes is an urgent engineering challenge. Surface alloying with high-energy beams improves the properties of steel products. In these processes, the alloying powders and the treated surfaces can be remelted by electron beam within a short time while the bulk structure of the component remains unchanged, resulting in minimal distortion. The paper presents the results of the electron beam surface alloying (EBSA) of H21 and L6 tool steels with the treatment pastes containing boron carbide and aluminum powders. (2) Methods: Two types of pastes were used for surface alloying: a single-component (B4C) paste and a two-component (B4C+Al) one. The microstructure, microhardness, wear resistance, and elemental and phase composition of the layers obtained on steels were investigated. (3) Results: Four layers up to 0.4 mm thick were distinguished on the surface of the steels after the EBSA. Metallographic analysis showed coarse dendrite formation in the layers embedded in matrices of a eutectic or a solid solution. Microhardness of the steels after the two-component EBSA was higher than after B4C EBSA, which was related to a higher concentration of hard phases, such as iron borides and carbides. In addition, aluminum boride was revealed by the XRD analysis on L6 steel after B4C+Al EBSA. (4) Conclusions: Wear test indicated that the most resistant samples were H21 steel after single B4C EBSA and L6 steel after B4C+Al EBSA. Both samples contained carbon particles in the layer contributing to the high wear resistance as a lubricant. The conducted research is beneficial for mechanical engineering, automotive engineering, medical technology, aerospace engineering, and related industries, where coatings with high microhardness, wear resistance, and surface quality are demanded.
- Open Access
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1393 (1) , 012110
Nanostructuring of the T31507 steel surface by vanadium borides under the influence electron beams in a vacuum
The microstructures and microhardness of boride layers formed on die steel of T31507 by electron-beam boron reduction in vacuum are investigated and compared. Formed layers have a heterogeneous structure, combining solid and plastic components, leading to a decrease in brittleness of the boride layer.
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1393 (1) , 012110
Open AccessNanostructuring of the T31507 steel surface by vanadium borides under the influence electron beams in a vacuum
The microstructures and microhardness of boride layers formed on die steel of T31507 by electron-beam boron reduction in vacuum are investigated and compared. Formed layers have a heterogeneous structure, combining solid and plastic components, leading to a decrease in brittleness of the boride layer.
- Open Access
- 4 May 2017
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 830 (1) , 012093
Creation of the nanostructured superhard and heatproof layers on die steels under influence of intensive electron beams in vacuum
Studying and comparing microstructure and microhardness of boride layers formed on die D2 steel by using different methods – electron beam borating with continuous and pulsed beams under vacuum. The created layers have a heterogeneous structure combining hard and plastic components resulting in decrease of boride layer embrittlement.
- 4 May 2017
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 830 (1) , 012093
Open AccessCreation of the nanostructured superhard and heatproof layers on die steels under influence of intensive electron beams in vacuum
Studying and comparing microstructure and microhardness of boride layers formed on die D2 steel by using different methods – electron beam borating with continuous and pulsed beams under vacuum. The created layers have a heterogeneous structure combining hard and plastic components resulting in decrease of boride layer embrittlement.