Lingaraju Sannananjapla Vageshappa
Research Subjects
Lingaraju Sannananjapla Vageshappa has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- H. S. Naveen Kumar
Department of Mechanical Engineering, Government Polytechnic, Holenarasipura, India
3 shared publications - Mahesh R. Jadhav
TKIET
3 shared publications - Mukund S. Dhuttargaon
Department of Mechanical Engineering, Tatyasaheb Kore Institute of Engineering and Technology, Warananagar, Warana University, Warananagar, India
3 shared publications - Saleemsab Doddamani
Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal, India
3 shared publications - Pramod V. Mulik
TKIET
2 shared publications - Prashant J. Patil
TKIET
2 shared publications
Latest Publications
- 26 August 2026
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 12 (4) , 155
Corrosion Rate and Hardness Degradation of LM6 Hybrid Composites Reinforced with Boron Carbide and Cow Dung Ash
- 26 August 2026
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 12 (4) , 155
Corrosion Rate and Hardness Degradation of LM6 Hybrid Composites Reinforced with Boron Carbide and Cow Dung Ash
- 25 June 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1195, 101-113
Wear and Friction Behaviour of Stir-Cast Al7075 Metal Matrix Composites Reinforced with TiC Particles
The tribological behavior of an aluminum metal matrix composite with TiC particles was investigated in this study. Composite specimens were prepared using the stir casting method, with the weight percentage of TiC particles with 2.5% Experiments were designed employing the Taguchi technique, with applied load, sliding velocity and sliding distance considered as control parameters with varying levels. Wear rate and coefficient of friction were determined using a Magnum pin-on-disc machine. ANOVA was then applied to assess the impact of each factor on wear rate and coefficient of friction. The results showed a significant effect of TiC reinforcement weight percentage on both specific wear rate and coefficient of friction. Increasing TiC reinforcement led to enhanced wear resistance of the composite material. Mathematical models were subsequently developed via regression to predict specific wear rate and coefficient of friction.
- 25 June 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1195, 101-113
Wear and Friction Behaviour of Stir-Cast Al7075 Metal Matrix Composites Reinforced with TiC Particles
The tribological behavior of an aluminum metal matrix composite with TiC particles was investigated in this study. Composite specimens were prepared using the stir casting method, with the weight percentage of TiC particles with 2.5% Experiments were designed employing the Taguchi technique, with applied load, sliding velocity and sliding distance considered as control parameters with varying levels. Wear rate and coefficient of friction were determined using a Magnum pin-on-disc machine. ANOVA was then applied to assess the impact of each factor on wear rate and coefficient of friction. The results showed a significant effect of TiC reinforcement weight percentage on both specific wear rate and coefficient of friction. Increasing TiC reinforcement led to enhanced wear resistance of the composite material. Mathematical models were subsequently developed via regression to predict specific wear rate and coefficient of friction.
- 5 December 2025
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 107 (1) , 287-297
Optimization and Statistical Analysis of Stress Parameters in Helical Gears Using Taguchi Method and ANOVA
- 5 December 2025
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 107 (1) , 287-297
Optimization and Statistical Analysis of Stress Parameters in Helical Gears Using Taguchi Method and ANOVA
- 4 December 2025
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48 (1) , 60
Nonlinear transient deflection of thermally loaded functionally graded porous skew plates
- 4 December 2025
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48 (1) , 60
Nonlinear transient deflection of thermally loaded functionally graded porous skew plates
- Open Access
- 5 November 2025
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 20 (75) , 265-280
Experimental and 3D numerical analysis on the effect of specimen thickness on fracture toughness of Al6061-SiC-cenosphere Hybrid composites
This study examines the fracture toughness of Al6061 alloy-based hybrid composites reinforced with silicon carbide particles and cenosphere microspheres. Aluminum alloy Al6061 is widely utilized in structural applications due to its balanced mechanical properties, and its hybridization with SiC and cenosphere reinforcements enhances its performance under critical loading conditions. The effect of specimen thickness on fracture toughness was examined by fabricating compact tension specimens in accordance with ASTM E399 standards, with thickness-to-width ratios ranging from 0.2 to 0.7. Controlled fatigue cracks were introduced, and both experimental testing and finite element simulations were conducted to assess the critical stress intensity factor and crack propagation behaviour across different thicknesses. Results show that the fracture toughness is constant after the B/W ratio of 0.5 and above, states as plane strain fracture toughness. The 3wt% SiC and 6wt% cenosphere in Al6061 shows the highest fracture toughness up to 15.56 MPa√m, due to the effective stress distribution and interfacial bonding. The fractography using the scanning electron microscopy reveals that particle debonding is major failure mechanism, with microcracking in 3wt% cenosphere composites and crack deflection and stress transfer at high reinforcement contents. Experimental results were well matched with the simulation model with ±10% differences, proving its validity.
- 5 November 2025
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 20 (75) , 265-280
Open AccessExperimental and 3D numerical analysis on the effect of specimen thickness on fracture toughness of Al6061-SiC-cenosphere Hybrid composites
This study examines the fracture toughness of Al6061 alloy-based hybrid composites reinforced with silicon carbide particles and cenosphere microspheres. Aluminum alloy Al6061 is widely utilized in structural applications due to its balanced mechanical properties, and its hybridization with SiC and cenosphere reinforcements enhances its performance under critical loading conditions. The effect of specimen thickness on fracture toughness was examined by fabricating compact tension specimens in accordance with ASTM E399 standards, with thickness-to-width ratios ranging from 0.2 to 0.7. Controlled fatigue cracks were introduced, and both experimental testing and finite element simulations were conducted to assess the critical stress intensity factor and crack propagation behaviour across different thicknesses. Results show that the fracture toughness is constant after the B/W ratio of 0.5 and above, states as plane strain fracture toughness. The 3wt% SiC and 6wt% cenosphere in Al6061 shows the highest fracture toughness up to 15.56 MPa√m, due to the effective stress distribution and interfacial bonding. The fractography using the scanning electron microscopy reveals that particle debonding is major failure mechanism, with microcracking in 3wt% cenosphere composites and crack deflection and stress transfer at high reinforcement contents. Experimental results were well matched with the simulation model with ±10% differences, proving its validity.
- 12 August 2025
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 95 (8) , 1-27
Influence of saturated porosity distributions on the geometrically nonlinear behavior of functionally graded porous plates in a thermal environment
- 12 August 2025
- Published by Springer Nature in Archive of Applied Mechanics
- Vol. 95 (8) , 1-27
Influence of saturated porosity distributions on the geometrically nonlinear behavior of functionally graded porous plates in a thermal environment
- 20 September 2024
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 10 (4) , 1-13
Investigation on Tribological Behavior of Al7075-TiC/Graphene Nano-composite Using Taguchi Method
- 20 September 2024
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 10 (4) , 1-13
Investigation on Tribological Behavior of Al7075-TiC/Graphene Nano-composite Using Taguchi Method
- Open Access
- 1 January 2022
- Published by MIM Research Group in Research on Engineering Structures and Materials
Effect of addition of TiC nanoparticles on the tensile strength of Al7075-graphene hybrid composites
Effect of addition of TiC nanoparticles on the tensile strength of Al7075-graphene hybrid composites
- 1 January 2022
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessEffect of addition of TiC nanoparticles on the tensile strength of Al7075-graphene hybrid composites
Effect of addition of TiC nanoparticles on the tensile strength of Al7075-graphene hybrid composites
- 25 November 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 54, 479-485
Processing, and Characterization of AZ91D Magnesium Alloy Reinforced Nano TiC, B4C, and HBN Composites
- 25 November 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 54, 479-485
Processing, and Characterization of AZ91D Magnesium Alloy Reinforced Nano TiC, B4C, and HBN Composites