N. A. Luchinkin
N. A. Luchinkin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
N G Razuvanov
Joint Institute for High Temperatures of RAS, Moscow, Russia
2 shared publicationsN. G. Razuvanov
National Research University Moscow Power Engineering Institute (NRU MPEI), Moscow, Russia
2 shared publications- P A Sardov
National Research University «MPEI», Moscow, Russia
2 shared publications I. A. Belyaev
Joint Institute for High Temperatures, Russian Academy of Sciences (JIHT RAS), 125412, Moscow, Russia
1 shared publicationO N Polyanskaya
Joint Institute for High Temperatures of RAS, Moscow, Russia
1 shared publicationO. N. Polyanskaya
National Research University Moscow Power Engineering Institute (NRU MPEI), Moscow, Russia
1 shared publication
Latest Publications
- Open Access
- 17 April 2025
- Published by Institute of Continuous Media Mechanics in Computational Continuum Mechanics
- Vol. 18 (1) , 45-56
Численное и экспериментальное моделирование конвективного теплообмена при течении жидкого металла в кольцевой трубе
Numerical simulation was performed to study the hydrodynamics and heat transfer characteristics of a curved pipe. The section of a uniformly heated pipe with a ratio of the bend radius to the pipe’s inner diameter being equal to 25 is considered. The differential conservation equations of a moving continuous medium are formulated in a curvilinear coordinate system. The system of equations for a cylindrical coordinate system, which includes additional terms that arise in the ring coordinate system, is taken as a basis. The problem’s geometry remains unchanged; it is still a straight pipe in cylindrical coordinates. In the simulation, a structured computational grid is used, and the influence of thermogravitational convection is considered. Experimental studies were carried out to investigate heat transfer in a liquid metal flow in a curved pipe with an inner diameter of 19 mm and a bend radius of 0.5 m. The experiments were conducted on a mercury loop at JIHT RAS in the range of the Reynolds number between 11,000 and 80,000 and at different heat loads. A probe with a correlation sensor that consists of two micro-thermopairs was used. The developed mechanism permits continuous movement of the probe in the pipe’s section, which is at a distance of 76 calibers to the heating zone. In the section placed in the stabilized region of the non-isothermal turbulent flow, the averaged velocity and temperature fields were measured in detail. The parameters, presented in dimensionless form, are compared with similar numerical simulation results. It was found that inertial and gravitational forces have a strong influence on the velocity and temperature profiles of the flow, which results in significant heterogeneity in the distribution of the wall temperature around the perimeter of the considered section of the pipe. The comparison shows good agreement between experimental and calculated data.
- 17 April 2025
- Published by Institute of Continuous Media Mechanics in Computational Continuum Mechanics
- Vol. 18 (1) , 45-56
Open AccessЧисленное и экспериментальное моделирование конвективного теплообмена при течении жидкого металла в кольцевой трубе
Numerical simulation was performed to study the hydrodynamics and heat transfer characteristics of a curved pipe. The section of a uniformly heated pipe with a ratio of the bend radius to the pipe’s inner diameter being equal to 25 is considered. The differential conservation equations of a moving continuous medium are formulated in a curvilinear coordinate system. The system of equations for a cylindrical coordinate system, which includes additional terms that arise in the ring coordinate system, is taken as a basis. The problem’s geometry remains unchanged; it is still a straight pipe in cylindrical coordinates. In the simulation, a structured computational grid is used, and the influence of thermogravitational convection is considered. Experimental studies were carried out to investigate heat transfer in a liquid metal flow in a curved pipe with an inner diameter of 19 mm and a bend radius of 0.5 m. The experiments were conducted on a mercury loop at JIHT RAS in the range of the Reynolds number between 11,000 and 80,000 and at different heat loads. A probe with a correlation sensor that consists of two micro-thermopairs was used. The developed mechanism permits continuous movement of the probe in the pipe’s section, which is at a distance of 76 calibers to the heating zone. In the section placed in the stabilized region of the non-isothermal turbulent flow, the averaged velocity and temperature fields were measured in detail. The parameters, presented in dimensionless form, are compared with similar numerical simulation results. It was found that inertial and gravitational forces have a strong influence on the velocity and temperature profiles of the flow, which results in significant heterogeneity in the distribution of the wall temperature around the perimeter of the considered section of the pipe. The comparison shows good agreement between experimental and calculated data.
- 2 October 2023
- Published by Pleiades Publishing Ltd in Thermal Engineering
- Vol. 70 (10) , 809-822
Heat Transfer in a “Tube-in-Channel” Combined System with an Upward Flow of Liquid Metal in a Transverse Magnetic Field
Investigations were performed of heat transfer to a forced upward flow of mercury in a tube inserted into a heated channel with a rectangular cross-section under the effect of a transverse magnetic field. The outer channel is filled with mercury and connected to a natural circulation loop. Liquid metal heat transfer is simulated in a cell of the cooling system of the channel-type liquid metal blanket for a Tokamak fusion reactor. Experimental data on temperature fields and heat-transfer performance in the inner tube and the outer channel were obtained in the mercury magnetohydrodynamic test rig using microthermocouple probes. Three different cases of natural circulation loop operation are examined: (I) the loop is off, convective flow can occur only in the space between the tube and the channel wall; (II) the loop is open and operates under adiabatic conditions; (III) the loop is open, water cooling is on. The results of measurement in the inner tube demonstrate that heat transfer in the tube-in-channel system is enhanced compared to the heat transfer in a separate tube both with and without a magnetic field. Under the experimental conditions, natural convection is induced by the buoyancy and electromagnetic forces in the gap between the tube and the channel wall. The configuration and structure of the flow in the gap change drastically in a transverse magnetic field, and the heat-transfer rate depends on the operating conditions in the natural circulation loop. Convection reduces temperature nonuniformities in the gap, and the heat transfer in the investigated “tube-in-channel” enhances greater when the natural circulation loop is activated and, especially, when it is additionally cooled. Low-frequency high-amplitude fluctuations induced by the instability of the natural convection and magnetohydrodynamic flows are observed in the gap.
- 2 October 2023
- Published by Pleiades Publishing Ltd in Thermal Engineering
- Vol. 70 (10) , 809-822
Heat Transfer in a “Tube-in-Channel” Combined System with an Upward Flow of Liquid Metal in a Transverse Magnetic Field
Investigations were performed of heat transfer to a forced upward flow of mercury in a tube inserted into a heated channel with a rectangular cross-section under the effect of a transverse magnetic field. The outer channel is filled with mercury and connected to a natural circulation loop. Liquid metal heat transfer is simulated in a cell of the cooling system of the channel-type liquid metal blanket for a Tokamak fusion reactor. Experimental data on temperature fields and heat-transfer performance in the inner tube and the outer channel were obtained in the mercury magnetohydrodynamic test rig using microthermocouple probes. Three different cases of natural circulation loop operation are examined: (I) the loop is off, convective flow can occur only in the space between the tube and the channel wall; (II) the loop is open and operates under adiabatic conditions; (III) the loop is open, water cooling is on. The results of measurement in the inner tube demonstrate that heat transfer in the tube-in-channel system is enhanced compared to the heat transfer in a separate tube both with and without a magnetic field. Under the experimental conditions, natural convection is induced by the buoyancy and electromagnetic forces in the gap between the tube and the channel wall. The configuration and structure of the flow in the gap change drastically in a transverse magnetic field, and the heat-transfer rate depends on the operating conditions in the natural circulation loop. Convection reduces temperature nonuniformities in the gap, and the heat transfer in the investigated “tube-in-channel” enhances greater when the natural circulation loop is activated and, especially, when it is additionally cooled. Low-frequency high-amplitude fluctuations induced by the instability of the natural convection and magnetohydrodynamic flows are observed in the gap.
- Open Access
- 1 October 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2057 (1) , 012018
Investigating heat transfer in an upward flow of liquid metal in the mercury facility with a loop of natural circulation
Research of heat transfer is performed in an upward flow of liquid metal in a vertical channel of rectangular cross-section under the condition of one-sided heating and in a vertical pipe in a mercury circuit with a natural circulation loop. Natural circulation loop enables measurements in mixed turbulent convection modes, which are inaccessible on a contour with a forced convection, that is, in the region of small Reynolds (Peclet) numbers of characteristics. Using a two-coordinate probe with a microthermocouple correlation sensor, profiles of averaged velocity and temperature and distribution of a wall temperature are obtained, and heat transfer coefficients are determined. Criterion dependences of Nusselt number on Peclet and Richardson are built. Experimental data on heat transfer are compared with similar data obtained earlier in a loop with a forced flow of mercury.
- 1 October 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2057 (1) , 012018
Open AccessInvestigating heat transfer in an upward flow of liquid metal in the mercury facility with a loop of natural circulation
Research of heat transfer is performed in an upward flow of liquid metal in a vertical channel of rectangular cross-section under the condition of one-sided heating and in a vertical pipe in a mercury circuit with a natural circulation loop. Natural circulation loop enables measurements in mixed turbulent convection modes, which are inaccessible on a contour with a forced convection, that is, in the region of small Reynolds (Peclet) numbers of characteristics. Using a two-coordinate probe with a microthermocouple correlation sensor, profiles of averaged velocity and temperature and distribution of a wall temperature are obtained, and heat transfer coefficients are determined. Criterion dependences of Nusselt number on Peclet and Richardson are built. Experimental data on heat transfer are compared with similar data obtained earlier in a loop with a forced flow of mercury.
- 1 May 2020
- Published by Pleiades Publishing Ltd in High Temperature
- Vol. 58 (3) , 400-409
Heat Transfer in Liquid Metal at an Upward Flow in a Pipe in Transverse Magnetic Field
The results of a study of the hydrodynamics and heat transfer in an upward mercury flow in a vertical pipe under the effect of a transverse magnetic field are presented. The problem simulates a liquid-metal flow in the poloidal channels of a blanket cooling system in a TOKAMAK fusion reactor. The experimental data on temperature fields and heat transfer obtained from probe measurements in a mercury magnetohydrodynamic test facility at JIHT RAS are given. These data are compared with the results of numerical modeling to determine the validity envelope for the computational model and to verify whether the experimental conditions were properly specified. Without a magnetic field, heat transfer is complicated by mixed turbulent convection; some regimes have a decrease in heat transfer of up to 30–40% in comparison with the forced-convection heat transfer. The effect of a transverse magnetic field drastically affects the regularities of heat transfer due to flow laminarization and the change in the velocity profile caused by the electromagnetic interaction. At the same time, in the studied region of flow conditions, mixed convection in uniformly heated pipes does not have a strong effect on the heat transfer in a magnetic field and does not induce fluctuating, return, or separated flows.
- 1 May 2020
- Published by Pleiades Publishing Ltd in High Temperature
- Vol. 58 (3) , 400-409
Heat Transfer in Liquid Metal at an Upward Flow in a Pipe in Transverse Magnetic Field
The results of a study of the hydrodynamics and heat transfer in an upward mercury flow in a vertical pipe under the effect of a transverse magnetic field are presented. The problem simulates a liquid-metal flow in the poloidal channels of a blanket cooling system in a TOKAMAK fusion reactor. The experimental data on temperature fields and heat transfer obtained from probe measurements in a mercury magnetohydrodynamic test facility at JIHT RAS are given. These data are compared with the results of numerical modeling to determine the validity envelope for the computational model and to verify whether the experimental conditions were properly specified. Without a magnetic field, heat transfer is complicated by mixed turbulent convection; some regimes have a decrease in heat transfer of up to 30–40% in comparison with the forced-convection heat transfer. The effect of a transverse magnetic field drastically affects the regularities of heat transfer due to flow laminarization and the change in the velocity profile caused by the electromagnetic interaction. At the same time, in the studied region of flow conditions, mixed convection in uniformly heated pipes does not have a strong effect on the heat transfer in a magnetic field and does not induce fluctuating, return, or separated flows.
- Open Access
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1359 (1) , 012017
Investigation of heat transfer in a liquid metal upflow in the MHD-channels applied to tokamak reactor blanket module
This article is devoted to experimental investigation of hydrodynamics and heat transfer in MHD flow configuration: upflow of mercury in a vertical round tube and rectangular duct with non-uniform heating in the transverse (coplanar) magnetic field. The problem is of interest for developing fusion reactor`s cooling systems. The liquid metal flow, in this case, will be complicated by influence of electromagnetic and thermogravitation forces. The experimental data were obtained by a proven probe technique for temperature measurements. The average temperature fields, wall temperature distributions, heat transfer coefficients and statistical characteristics of temperature fluctuations have been obtained and compared throughout the length of test section (pipe or duct) detecting the channel geometry influence.
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1359 (1) , 012017
Open AccessInvestigation of heat transfer in a liquid metal upflow in the MHD-channels applied to tokamak reactor blanket module
This article is devoted to experimental investigation of hydrodynamics and heat transfer in MHD flow configuration: upflow of mercury in a vertical round tube and rectangular duct with non-uniform heating in the transverse (coplanar) magnetic field. The problem is of interest for developing fusion reactor`s cooling systems. The liquid metal flow, in this case, will be complicated by influence of electromagnetic and thermogravitation forces. The experimental data were obtained by a proven probe technique for temperature measurements. The average temperature fields, wall temperature distributions, heat transfer coefficients and statistical characteristics of temperature fluctuations have been obtained and compared throughout the length of test section (pipe or duct) detecting the channel geometry influence.