M. Siva Sankari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
M. Siva Sankari has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- M. Eswara Rao
Department of Mathematics Saveetha School of Engineering, SIMATS Chennai Tamil Nadu India
2 shared publications - Oluwole Daniel Makinde
Faculty of Military Science, Stellenbosch University, Stellenbosch, South Africa
2 shared publications - Waris Khan
Department of Mathematics and Statistics, Hazara University
2 shared publications - Ali Jawad Chamkha
Faculty of Engineering, Kuwait College of Science and Technology, Doha District, Kuwait
1 shared publication - Aurang Zaib
Department of Mathematics, University of Karachi, Karachi 75270, Pakistan
1 shared publication Bashir Salah
Department of Industrial Engineering, College of Engineering King Saud University
1 shared publication
Latest Publications
- 8 October 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Nanoscience
Numerical Analysis of Heat Transfer Efficiency in a Two-Phase Non-Newtonian Nanofluid Model with Chemical Reaction
Second-grade nanofluids are both flexible and viscous, which is why they are valuable in thermal manufacturing, the polymer industry and biological procedures. Whether injection or suction is used, an increase in the fluid parameter, porosity or inertia coefficient results in a lower velocity. The thickness of the thermal boundary layer rises as thermal radiation, Brownian motion and thermophoresis become more significant. Higher Schmidt numbers, faster chemical reactions, larger bioconvection Lewis numbers and greater Peclet numbers all cause the density of the microorganisms to decrease. Although previous studies have looked at Darcy and Forchheimer porous resistance, bioconvection, suction or injection, curved stretching surfaces and various thermal boundary conditions individually, the combined effect of these factors has not been thoroughly examined. This study examines the flow of a nanofluid containing swimming microorganisms over a curved stretching surface under Newtonian heating and a steady wall temperature. The model includes heat radiation, internal heat generation, random particle motion, thermophoresis and chemical reactions. Solving the equations with MATLAB’s bvp4c solver provides insights that may help explain and improve the design of biological and heat systems, including microbial fuel cells, bioreactors and groundwater cleaning methods.
- 8 October 2026
- Published by World Scientific Pub Co Pte Ltd in International Journal of Nanoscience
Numerical Analysis of Heat Transfer Efficiency in a Two-Phase Non-Newtonian Nanofluid Model with Chemical Reaction
Second-grade nanofluids are both flexible and viscous, which is why they are valuable in thermal manufacturing, the polymer industry and biological procedures. Whether injection or suction is used, an increase in the fluid parameter, porosity or inertia coefficient results in a lower velocity. The thickness of the thermal boundary layer rises as thermal radiation, Brownian motion and thermophoresis become more significant. Higher Schmidt numbers, faster chemical reactions, larger bioconvection Lewis numbers and greater Peclet numbers all cause the density of the microorganisms to decrease. Although previous studies have looked at Darcy and Forchheimer porous resistance, bioconvection, suction or injection, curved stretching surfaces and various thermal boundary conditions individually, the combined effect of these factors has not been thoroughly examined. This study examines the flow of a nanofluid containing swimming microorganisms over a curved stretching surface under Newtonian heating and a steady wall temperature. The model includes heat radiation, internal heat generation, random particle motion, thermophoresis and chemical reactions. Solving the equations with MATLAB’s bvp4c solver provides insights that may help explain and improve the design of biological and heat systems, including microbial fuel cells, bioreactors and groundwater cleaning methods.
- Open Access
- 1 March 2026
- Published by Three E Science Institute in International Journal of Environment, Engineering and Education
- Vol. 8 (1) , 122-137
Effect of Vortex-Generator Planform and Height on the Trade-Off between Lift Enhancement and Wake Contraction around a Circular Cylinder
Passive flow control of circular-cylinder wakes remains important because wake organizations govern aerodynamic loading, force fluctuations, and vortex-induced response. This study examines how vortex-generator (VG) planform and height affect lift behavior and near-wake structure around a circular cylinder. Triangular and ogival VGs with heights of 4, 7, and 10 mm were mounted at the cylinder apex and evaluated using three-dimensional transient URANS simulations with the SST k–ω model at Re = 53,000. Supporting wind-tunnel force measurements were also performed to assess whether the numerical trends were qualitatively reproduced experimentally. All VG-equipped configurations reduced the recirculation region, narrowed the wake, and decreased the centerline velocity deficit relative to the clean cylinder. Among the triangular cases, the 10 mm VG produced the strongest wake contraction, reducing the recirculation length from 1.35D to 0.70D. Among the ogival cases, the 10 mm VG generated the highest peak lift coefficient (approximately 1.45), although its wake contraction remained slightly weaker than that of the corresponding triangular configuration. These results show that the geometry yielding the strongest wake suppression is not identical to that giving the highest lift enhancement. The wind-tunnel measurements reproduced the overall ranking trends. However, because the experimental inflow conditions were not Reynolds-number matched to the numerical setup, the comparison is interpreted as qualitative trend support rather than strict validation. The results demonstrate that the VG planform and height jointly control the trade-off between wake contraction and lift enhancement.
- 1 March 2026
- Published by Three E Science Institute in International Journal of Environment, Engineering and Education
- Vol. 8 (1) , 122-137
Open AccessEffect of Vortex-Generator Planform and Height on the Trade-Off between Lift Enhancement and Wake Contraction around a Circular Cylinder
Passive flow control of circular-cylinder wakes remains important because wake organizations govern aerodynamic loading, force fluctuations, and vortex-induced response. This study examines how vortex-generator (VG) planform and height affect lift behavior and near-wake structure around a circular cylinder. Triangular and ogival VGs with heights of 4, 7, and 10 mm were mounted at the cylinder apex and evaluated using three-dimensional transient URANS simulations with the SST k–ω model at Re = 53,000. Supporting wind-tunnel force measurements were also performed to assess whether the numerical trends were qualitatively reproduced experimentally. All VG-equipped configurations reduced the recirculation region, narrowed the wake, and decreased the centerline velocity deficit relative to the clean cylinder. Among the triangular cases, the 10 mm VG produced the strongest wake contraction, reducing the recirculation length from 1.35D to 0.70D. Among the ogival cases, the 10 mm VG generated the highest peak lift coefficient (approximately 1.45), although its wake contraction remained slightly weaker than that of the corresponding triangular configuration. These results show that the geometry yielding the strongest wake suppression is not identical to that giving the highest lift enhancement. The wind-tunnel measurements reproduced the overall ranking trends. However, because the experimental inflow conditions were not Reynolds-number matched to the numerical setup, the comparison is interpreted as qualitative trend support rather than strict validation. The results demonstrate that the VG planform and height jointly control the trade-off between wake contraction and lift enhancement.
- 1 May 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (5)
Activation energy and motile microorganism influence on MHD Jeffery nanofluid with stratifications
This study investigates the use of reacting and radiating nanofluids to enhance heat and mass transfer in non-Newtonian hydromagnetic bioconvection over a stretching porous vertical plate. It focuses on the combined effects of a magnetic field, Joule heating, porous medium permeability, viscous dissipation, buoyancy forces, thermal radiation, chemical reactions, and the bioconvection of motile microorganisms to prevent the settling of nano entities. The mathematical model transforms the partial differential equations (PDEs) governing the conservation of mass, momentum, energy, nanoparticle concentration, and microorganism density into ordinary differential equations through appropriate similarity transformations. Semi-analytical solutions are obtained using the homotopy analysis method. The effects of various thermophysical parameters on the overall flow structure, including microbial diffusion rates and heat and mass transfer rates, are presented graphically and in tables. Key findings reveal that higher bioconvection Rayleigh numbers and magnetic field intensity reduce the flow rate, while increased thermophoresis and Brownian motion enhance nanofluid temperature profiles. These insights hold significant applications in polymerization, fuel industry, bioengineering, and biomedicine.
- 1 May 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (5)
Activation energy and motile microorganism influence on MHD Jeffery nanofluid with stratifications
This study investigates the use of reacting and radiating nanofluids to enhance heat and mass transfer in non-Newtonian hydromagnetic bioconvection over a stretching porous vertical plate. It focuses on the combined effects of a magnetic field, Joule heating, porous medium permeability, viscous dissipation, buoyancy forces, thermal radiation, chemical reactions, and the bioconvection of motile microorganisms to prevent the settling of nano entities. The mathematical model transforms the partial differential equations (PDEs) governing the conservation of mass, momentum, energy, nanoparticle concentration, and microorganism density into ordinary differential equations through appropriate similarity transformations. Semi-analytical solutions are obtained using the homotopy analysis method. The effects of various thermophysical parameters on the overall flow structure, including microbial diffusion rates and heat and mass transfer rates, are presented graphically and in tables. Key findings reveal that higher bioconvection Rayleigh numbers and magnetic field intensity reduce the flow rate, while increased thermophoresis and Brownian motion enhance nanofluid temperature profiles. These insights hold significant applications in polymerization, fuel industry, bioengineering, and biomedicine.
- 1 April 2024
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 86 (16) , 5603-5625
Homotopic analysis for bioconvection of Casson nanofluid flow over an exponential stretching sheet with activation energy and motile microorganism
- 1 April 2024
- Published by Taylor & Francis in Numerical Heat Transfer, Part A: Applications
- Vol. 86 (16) , 5603-5625
Homotopic analysis for bioconvection of Casson nanofluid flow over an exponential stretching sheet with activation energy and motile microorganism
- Open Access
- 2 January 2023
- Published by Wiley in Journal of Nanomaterials
- Vol. 2023, 1-11
On the Role of Bioconvection and Activation Energy for MHD-Stretched Flow of Williamson and Casson Nanofluid Transportation across a Porous Medium Past a Permeable Sheet
The goal of the current study is to theoretically evaluate the heat and mass transfer behavior of magnetohydrodynamic Casson and Williamson fluids as they pass through a stretched sheet with Brownian and thermophoresis effects. The evolution of high-density heat devices necessitates efficient thermal transportation. For these requirements, the concept of nanofluid plays an active role. This article describes the effects of Cattaneo–Christov. This study introduces new concepts such as motile microorganism bioconvection, non-Fourier heat flux, and activation energy. A Runge–Kutta-based shooting procedure is used to solve the problem. The effects of the relevant parameters on velocity, thermal, concentration, and motile microorganisms are depicted graphically. The computed reduced Nusselt, Sherwood, and motile density numbers are displayed in tables in this study. When compared to the Williamson fluid, the thermal and concentration fields of the Casson fluid are heavily influenced by the parameters.
- 2 January 2023
- Published by Wiley in Journal of Nanomaterials
- Vol. 2023, 1-11
Open AccessOn the Role of Bioconvection and Activation Energy for MHD-Stretched Flow of Williamson and Casson Nanofluid Transportation across a Porous Medium Past a Permeable Sheet
The goal of the current study is to theoretically evaluate the heat and mass transfer behavior of magnetohydrodynamic Casson and Williamson fluids as they pass through a stretched sheet with Brownian and thermophoresis effects. The evolution of high-density heat devices necessitates efficient thermal transportation. For these requirements, the concept of nanofluid plays an active role. This article describes the effects of Cattaneo–Christov. This study introduces new concepts such as motile microorganism bioconvection, non-Fourier heat flux, and activation energy. A Runge–Kutta-based shooting procedure is used to solve the problem. The effects of the relevant parameters on velocity, thermal, concentration, and motile microorganisms are depicted graphically. The computed reduced Nusselt, Sherwood, and motile density numbers are displayed in tables in this study. When compared to the Williamson fluid, the thermal and concentration fields of the Casson fluid are heavily influenced by the parameters.