Mojtaba Ashouri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mojtaba Ashouri has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Mohsen Nazari
Faculty of Mechanical Engineering, Shahrood University of Technology, Shahrood, Iran
5 shared publications A. Tamayol
1 shared publicationAli Tamayol
1 shared publicationJ. P. Meyer
University of Pretoria
1 shared publicationM. Karami
1 shared publicationM. M. Shahmardan
Shahrood University of Technology
1 shared publication
Latest Publications
- Open Access
An Experimental Study of Wall Effect on a Hot Settling Sphere in a Newtonian-Fluid-Contained Block Using Photography
In this study, the effect of temperature on the velocity and trajectory of a hot sphere falling in a water block was experimentally investigated. The sphere, 12 mm in diameter, was thrown through the water inside an enclosure at the ambient temperature by an electromagnetic attachment mechanism, and the particle velocity was recorded by a high-speed camera at 2000 fps. Then, using an image-processing algorithm, the real-time particle location was extracted and its velocity was measured. The results of the cold sphere falling test were compared with those obtained from the numerical solving by the governing equations. An electric heater was used to heat the sphere up to 100, 200, and 300 °C in order to investigate the effect of temperature on the sphere. The sphere was thrown upon reaching the desired temperature. By increasing the temperature, the sphere’s velocity was increased up to around 40% of the velocity of the cold sphere. Further, the sphere was thrown from a point in the vicinity of the wall to investigate the wall impact on the particle movement. This led the sphere to deviate from its trajectory, with the deviation in the cold sphere being negligible, i.e., around 30% of the sphere’s diameter. However, the rate of deviation was much more notable upon increasing the temperature. The deviation start point varied depending on the sphere’s temperature, with the highest deviation that was observed for a sphere with a temperature of 100 °C. Ultimately, the sphere traveled in a more extended way, with no deviation from the main trajectory, when its temperature was increased.
Open AccessAn Experimental Study of Wall Effect on a Hot Settling Sphere in a Newtonian-Fluid-Contained Block Using Photography
In this study, the effect of temperature on the velocity and trajectory of a hot sphere falling in a water block was experimentally investigated. The sphere, 12 mm in diameter, was thrown through the water inside an enclosure at the ambient temperature by an electromagnetic attachment mechanism, and the particle velocity was recorded by a high-speed camera at 2000 fps. Then, using an image-processing algorithm, the real-time particle location was extracted and its velocity was measured. The results of the cold sphere falling test were compared with those obtained from the numerical solving by the governing equations. An electric heater was used to heat the sphere up to 100, 200, and 300 °C in order to investigate the effect of temperature on the sphere. The sphere was thrown upon reaching the desired temperature. By increasing the temperature, the sphere’s velocity was increased up to around 40% of the velocity of the cold sphere. Further, the sphere was thrown from a point in the vicinity of the wall to investigate the wall impact on the particle movement. This led the sphere to deviate from its trajectory, with the deviation in the cold sphere being negligible, i.e., around 30% of the sphere’s diameter. However, the rate of deviation was much more notable upon increasing the temperature. The deviation start point varied depending on the sphere’s temperature, with the highest deviation that was observed for a sphere with a temperature of 100 °C. Ultimately, the sphere traveled in a more extended way, with no deviation from the main trajectory, when its temperature was increased.
- 26 April 2019
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 138 (1) , 805-817
Thermal characteristics of CPU cooling by using a novel porous heat sink and nanofluids
- 26 April 2019
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 138 (1) , 805-817
Thermal characteristics of CPU cooling by using a novel porous heat sink and nanofluids
- 1 January 2017
- Published by Elsevier in Applied Thermal Engineering
- Vol. 111, 39-48
Unsteady heat transfer from a reservoir fluid by employing metal foam tube, helically tube and straight tube: A comparative experimental study
- 1 January 2017
- Published by Elsevier in Applied Thermal Engineering
- Vol. 111, 39-48
Unsteady heat transfer from a reservoir fluid by employing metal foam tube, helically tube and straight tube: A comparative experimental study
- 1 February 2015
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 88, 33-39
Experimental study of convective heat transfer of a nanofluid through a pipe filled with metal foam
- 1 February 2015
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 88, 33-39
Experimental study of convective heat transfer of a nanofluid through a pipe filled with metal foam
- 1 September 2014
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 57, 371-377
Comparing the thermal performance of water, Ethylene Glycol, Alumina and CNT nanofluids in CPU cooling: Experimental study
- 1 September 2014
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 57, 371-377
Comparing the thermal performance of water, Ethylene Glycol, Alumina and CNT nanofluids in CPU cooling: Experimental study