Tolga Topgül
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tolga Topgül has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Regaip Menküç
Gazı University
2 shared publications - Suat Sarıdemir
Düzce University
2 shared publications - Çağatay Zaman
GAZİ ÜNİVERSİTESİ, FEN BİLİMLERİ ENSTİTÜSÜ, OTOMOTİV MÜHENDİSLİĞİ (YL) (TEZLİ)
2 shared publications - Abdullah Onur Özdemi̇r
Gazi Üniversitesi, Teknoloji Fakültesi
1 shared publication - Can Cinar
Gazi Üniversitesi
1 shared publication - Erdi Demi̇rCi̇
Oyak Beton San. ve Tic. AŞ
1 shared publication
Latest Publications
- Open Access
- 28 December 2023
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 11 (4) , 1283-1295
Experimental Investigation of the Effects of E85 and Gasoline on NO Emission in a Spark Ignition Engine
Energy need is one of the indispensable needs of human beings. At this point, the important thing is to use the available resource that is sustainable, economical, and sensitive to the ecosystem. For this reason, alternative fuels will maintain their importance in the future as they do today. Internal combustion engines continue to be used as power plants for conventional and hybrid vehicles. The sustainability of internal combustion engines depends on their energy consumption and the emissions released. In this study, the effects of E85 and gasoline on NO emissions have been investigated experimentally by considering ignition timing and relative air/fuel ratio in a spark ignition engine. The experiments have been performed on the Ricardo Hydra research engine at 2000 rpm engine speed and a 10:1 compression ratio. The experimental results show that engine output power obtained using E85 was similar to or higher than that of E0. The exhaust gas temperatures for E85 decreased by an average of 22.6 °C, compared to E0. When all experimental data obtained with E0 and E85 were compared with each other, it was seen that gravimetric fuel consumption and brake specific fuel consumption were increased on average by 39.3% and 37.5%, respectively. The results of this study show that especially the improvement of E85 in NO emission is remarkable. Considering the maximum NO point at 1.05 or 1.1 relative air/fuel ratio, a 38.4% reduction in brake specific NO was obtained with E85.
- 28 December 2023
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 11 (4) , 1283-1295
Open AccessExperimental Investigation of the Effects of E85 and Gasoline on NO Emission in a Spark Ignition Engine
Energy need is one of the indispensable needs of human beings. At this point, the important thing is to use the available resource that is sustainable, economical, and sensitive to the ecosystem. For this reason, alternative fuels will maintain their importance in the future as they do today. Internal combustion engines continue to be used as power plants for conventional and hybrid vehicles. The sustainability of internal combustion engines depends on their energy consumption and the emissions released. In this study, the effects of E85 and gasoline on NO emissions have been investigated experimentally by considering ignition timing and relative air/fuel ratio in a spark ignition engine. The experiments have been performed on the Ricardo Hydra research engine at 2000 rpm engine speed and a 10:1 compression ratio. The experimental results show that engine output power obtained using E85 was similar to or higher than that of E0. The exhaust gas temperatures for E85 decreased by an average of 22.6 °C, compared to E0. When all experimental data obtained with E0 and E85 were compared with each other, it was seen that gravimetric fuel consumption and brake specific fuel consumption were increased on average by 39.3% and 37.5%, respectively. The results of this study show that especially the improvement of E85 in NO emission is remarkable. Considering the maximum NO point at 1.05 or 1.1 relative air/fuel ratio, a 38.4% reduction in brake specific NO was obtained with E85.
- Open Access
- 5 July 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 26 (2) , 877-887
Design and Optimization of the Single-Speed Transmission in an Electric Vehicle
Bu çalışmada elektrikli bir taşıtın güç aktarma sisteminde kullanılacak tek vitesli dişli kutusunun tasarımı ve mukavemet kontrolleri yapılmıştır. Dişli kutusunun tahriki elektrik motoru tarafından sağlandığından motorun tork-devir karakteristiği referans alınarak mukavemet hesapları yapılmıştır. Dişli çiftlerin çalışması esnasında en sık karşılaşılan sorun olan aşırı gerilmeden kaynaklı kök kırılmalarının oluşmaması için gerilmeler KISSsoft yazılımı ile analiz edilerek optimizasyon yapılmıştır. Analizlerde diş yanak mukavemeti ve diş dibi gerilmeleri üzerinde durulmuştur. Geometrik parametreler ISO 6336 “Düz ve helisel dişlilerin yük kapasitesinin hesaplanması” standardında belirtilen emniyet katsayıları dikkate alınarak çözümler yapılmış ve dişli mukavemeti üzerindeki etkileri gözlemlenmiştir. Sonuçlar, birinci dişli çiftinin 2,5 mm modül, 22° helis açısı ve pinyon dişli çark için 32 diş sayısının optimal olduğunu göstermektedir. İkinci dişli çiftinin optimum parametreleri ise 2,5 mm modül, 20° helis açısı ve 33 diş sayısına sahip pinyon dişli olarak belirlenmiştir.
- 5 July 2023
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 26 (2) , 877-887
Open AccessDesign and Optimization of the Single-Speed Transmission in an Electric Vehicle
Bu çalışmada elektrikli bir taşıtın güç aktarma sisteminde kullanılacak tek vitesli dişli kutusunun tasarımı ve mukavemet kontrolleri yapılmıştır. Dişli kutusunun tahriki elektrik motoru tarafından sağlandığından motorun tork-devir karakteristiği referans alınarak mukavemet hesapları yapılmıştır. Dişli çiftlerin çalışması esnasında en sık karşılaşılan sorun olan aşırı gerilmeden kaynaklı kök kırılmalarının oluşmaması için gerilmeler KISSsoft yazılımı ile analiz edilerek optimizasyon yapılmıştır. Analizlerde diş yanak mukavemeti ve diş dibi gerilmeleri üzerinde durulmuştur. Geometrik parametreler ISO 6336 “Düz ve helisel dişlilerin yük kapasitesinin hesaplanması” standardında belirtilen emniyet katsayıları dikkate alınarak çözümler yapılmış ve dişli mukavemeti üzerindeki etkileri gözlemlenmiştir. Sonuçlar, birinci dişli çiftinin 2,5 mm modül, 22° helis açısı ve pinyon dişli çark için 32 diş sayısının optimal olduğunu göstermektedir. İkinci dişli çiftinin optimum parametreleri ise 2,5 mm modül, 20° helis açısı ve 33 diş sayısına sahip pinyon dişli olarak belirlenmiştir.
- Open Access
- 4 January 2023
- Published by Faculty of Mechanical Engineering in Strojniški vestnik - Journal of Mechanical Engineering
- Vol. 68 (12) , 757-770
Design, Manufacturing, and Thermodynamic Analysis of a Gamma-type Stirling Engine Powered by Solar Energy
Stirling engines are external combustion engines. This feature eliminates the possible dependency of the engine on a specific energy resource and allows it to work with diverse energy sources, especially solar and other renewable energy sources. Also, Stirling engines could be built in different configurations that have a significant impact on the engine performance. With these aspects, Stirling engines have attracted the attention of researchers. In this study, firstly, a double-cylinder V-type air compressor has been converted to a gamma-type Stirling engine. The block, cylinders, connecting rods, and the crank mechanism of the compressor have been used in the converted engine. For this reason, the air compressor has determined some features of the Stirling engine, such as phase angle, strokes, and cylinder diameter. Other parts of the engine, such as piston, cylinder head, displacer, and displacer cylinder have been manufactured. Secondly, the optimum operating parameters to provide maximum thermal efficiency have been investigated using the nodal thermodynamic analysis considering that the engine is powered by solar energy. In the analysis, helium as the working fluid is used due to its suitable thermodynamic features and safety usage. The optimum working fluid mass and engine speed have been determined as 0.15 g and 100 rad/s for all temperatures (750, 800, and 850 K). Also, the optimum displacer height has been preferred as 190 mm since there is no significant improvement in the thermal efficiency after this dimension. The maximum thermal efficiency has been obtained as 46.5%.
- 4 January 2023
- Published by Faculty of Mechanical Engineering in Strojniški vestnik - Journal of Mechanical Engineering
- Vol. 68 (12) , 757-770
Open AccessDesign, Manufacturing, and Thermodynamic Analysis of a Gamma-type Stirling Engine Powered by Solar Energy
Stirling engines are external combustion engines. This feature eliminates the possible dependency of the engine on a specific energy resource and allows it to work with diverse energy sources, especially solar and other renewable energy sources. Also, Stirling engines could be built in different configurations that have a significant impact on the engine performance. With these aspects, Stirling engines have attracted the attention of researchers. In this study, firstly, a double-cylinder V-type air compressor has been converted to a gamma-type Stirling engine. The block, cylinders, connecting rods, and the crank mechanism of the compressor have been used in the converted engine. For this reason, the air compressor has determined some features of the Stirling engine, such as phase angle, strokes, and cylinder diameter. Other parts of the engine, such as piston, cylinder head, displacer, and displacer cylinder have been manufactured. Secondly, the optimum operating parameters to provide maximum thermal efficiency have been investigated using the nodal thermodynamic analysis considering that the engine is powered by solar energy. In the analysis, helium as the working fluid is used due to its suitable thermodynamic features and safety usage. The optimum working fluid mass and engine speed have been determined as 0.15 g and 100 rad/s for all temperatures (750, 800, and 850 K). Also, the optimum displacer height has been preferred as 190 mm since there is no significant improvement in the thermal efficiency after this dimension. The maximum thermal efficiency has been obtained as 46.5%.
- 30 June 2022
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 10 (2) , 230-241
İçten Yanmalı Motorlu Bir Taşıtta Titreşim ve Gürültünün Deneysel Olarak Belirlenmesi
İçten yanmalı motora sahip bir taşıtın sürüş karakteristiğini etkileyen temel parametreler motor devri ve motor yüküdür. Sürücü temelde taşıt hızı ayarlar ve bu ayar için temel kontrol noktası gaz pedalıdır. Gaz pedalına basma miktarı, taşıtın karşılaştığı dirençlere ve vites kademesine bağlıdır. Bu çalışmanın amacı taşıtın temel sürüş parametrelerindeki değişimin titreşim ve gürültüye etkisini deneysel olarak incelemektir. Bu amaçla düz yol koşullarında ve belirli bir vites kademesinde (5. vites) taşıt hızına bağlı olarak titreşim ve gürültü ölçümleri gerçekleştirilmiştir. Taşıt hızına bağlı olarak toplam ortalama titreşim yaklaşık 3 kat, gürültü ise 9,4 dB(A) artmıştır. Ayrıca 50 km/h ve 90 km/h taşıt hızlarında elde edilen veriler 4. vites kademesiyle karşılaştırılmıştır. 5. vitesteki ölçüm sonuçları ile karşılaştırıldığında toplam ortalama titreşim 4. vites kademesinde 50 km/h taşıt hızında %18 ve 90 km/h taşıt hızında %43,4 artış göstermiştir. Gürültü ölçüm sonuçları karşılaştırıldığında ise; her iki vites kademesi arasında dikkate değer bir fark görülmemiştir.
- 30 June 2022
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 10 (2) , 230-241
İçten Yanmalı Motorlu Bir Taşıtta Titreşim ve Gürültünün Deneysel Olarak Belirlenmesi
İçten yanmalı motora sahip bir taşıtın sürüş karakteristiğini etkileyen temel parametreler motor devri ve motor yüküdür. Sürücü temelde taşıt hızı ayarlar ve bu ayar için temel kontrol noktası gaz pedalıdır. Gaz pedalına basma miktarı, taşıtın karşılaştığı dirençlere ve vites kademesine bağlıdır. Bu çalışmanın amacı taşıtın temel sürüş parametrelerindeki değişimin titreşim ve gürültüye etkisini deneysel olarak incelemektir. Bu amaçla düz yol koşullarında ve belirli bir vites kademesinde (5. vites) taşıt hızına bağlı olarak titreşim ve gürültü ölçümleri gerçekleştirilmiştir. Taşıt hızına bağlı olarak toplam ortalama titreşim yaklaşık 3 kat, gürültü ise 9,4 dB(A) artmıştır. Ayrıca 50 km/h ve 90 km/h taşıt hızlarında elde edilen veriler 4. vites kademesiyle karşılaştırılmıştır. 5. vitesteki ölçüm sonuçları ile karşılaştırıldığında toplam ortalama titreşim 4. vites kademesinde 50 km/h taşıt hızında %18 ve 90 km/h taşıt hızında %43,4 artış göstermiştir. Gürültü ölçüm sonuçları karşılaştırıldığında ise; her iki vites kademesi arasında dikkate değer bir fark görülmemiştir.
- 21 June 2022
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 38 (1) , 45-56
Üç silindirli gama tipi bir Stirling motorunun ve geleneksel gama tipi bir Stirling motorunun nodal termodinamik analizleri ve performans kıyaslaması
Geleneksel gama tipi Stirling motorlarında iki silindir mevcut olup silindirlerden birisi aracılığı ile çalışma gazının sıkıştırılması ve genişletilmesi işlemleri, diğeri aracılığı ile çalışma gazının sabit hacimde ısıtılması ve soğutulması işlemleri gerçekleştirilmektedir. Geleneksel gama tipi motorlarda soğuk ve sıcak hacimlerin aynı silindirde bulunması nedeni ile sıcak uçtan soğuk uca iletimle önemli bir miktarda ısı kaybı olmaktadır. Ayrıca dispileyser’ in yapımı oldukça külfetli bir iştir. Bu problemleri yok etmek için, son zamanlarda sıcak ve soğuk hacimleri ayrı ayrı silindirlerde bulunan üç silindirli gama tipi bir motor modeli tanıtılmıştır. Bu motorlarda bulunan silindirlerden birisi sıcak hacim olarak bir diğeri soğuk hacim olarak üçüncüsü de güç silindiri olarak görev yapmaktadır. Bu motorların termodinamik süreçleri geleneksel gama tipi motorunkine çok benzediği için bunlara üç silindirli gama tipi motor adı verilmiştir. Her üç silindirin içerisinde alışılmış tipten pistonlar çalışmaktadır. Bu araştırmada geleneksel gama tipi bir motorun ve üç silindirli gama tipi bir motorun nodal termodinamik analizleri yapılarak performansları kıyaslanmıştır. Motorların çevrimlik işlerinin ve verimlerinin birbirine çok yakın olduğu görülmektedir. Yüksek hızlarda ve yüksek basınçlarında geleneksel gama tipi motorun, yüksek sıkıştırma oranında ise üç silindirli gama tipi motorun az miktarda avantajlı olduğu görülmektedir.
- 21 June 2022
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 38 (1) , 45-56
Üç silindirli gama tipi bir Stirling motorunun ve geleneksel gama tipi bir Stirling motorunun nodal termodinamik analizleri ve performans kıyaslaması
Geleneksel gama tipi Stirling motorlarında iki silindir mevcut olup silindirlerden birisi aracılığı ile çalışma gazının sıkıştırılması ve genişletilmesi işlemleri, diğeri aracılığı ile çalışma gazının sabit hacimde ısıtılması ve soğutulması işlemleri gerçekleştirilmektedir. Geleneksel gama tipi motorlarda soğuk ve sıcak hacimlerin aynı silindirde bulunması nedeni ile sıcak uçtan soğuk uca iletimle önemli bir miktarda ısı kaybı olmaktadır. Ayrıca dispileyser’ in yapımı oldukça külfetli bir iştir. Bu problemleri yok etmek için, son zamanlarda sıcak ve soğuk hacimleri ayrı ayrı silindirlerde bulunan üç silindirli gama tipi bir motor modeli tanıtılmıştır. Bu motorlarda bulunan silindirlerden birisi sıcak hacim olarak bir diğeri soğuk hacim olarak üçüncüsü de güç silindiri olarak görev yapmaktadır. Bu motorların termodinamik süreçleri geleneksel gama tipi motorunkine çok benzediği için bunlara üç silindirli gama tipi motor adı verilmiştir. Her üç silindirin içerisinde alışılmış tipten pistonlar çalışmaktadır. Bu araştırmada geleneksel gama tipi bir motorun ve üç silindirli gama tipi bir motorun nodal termodinamik analizleri yapılarak performansları kıyaslanmıştır. Motorların çevrimlik işlerinin ve verimlerinin birbirine çok yakın olduğu görülmektedir. Yüksek hızlarda ve yüksek basınçlarında geleneksel gama tipi motorun, yüksek sıkıştırma oranında ise üç silindirli gama tipi motorun az miktarda avantajlı olduğu görülmektedir.
- 1 June 2022
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 25 (2) , 861-869
Buji İle Ateşlemeli Bir Motorda İkincil Hava Enjeksiyonunun Egzoz Emisyonları ve Katalitik Konvertör Verimine Etkisinin Deneysel Analizi
İçten yanmalı motorlarda gücün elde edilmesi yanma olayının bir sonucunun olması ve yanmanın belirli bir süre içerisinde gerçekleşmesi kirletici emisyonlarını kaçınılmaz yapmaktadır. Ancak emisyon kontrol yöntemleriyle bu durum kontrol altına alınmaya çalışılmaktadır. Bu çalışmada da tek nokta yakıt enjeksiyonuna sahip buji ile ateşlemeli motorda ikincil hava enjeksiyonunun (İHE) ve üç yollu katalitik konvertörün CO, HC ve NO emisyonlarına etkisi deneysel olarak incelenmiştir. Deneyler 1500-5000 rpm motor devri aralığında tam yükte ve 2500 rpm sabit motor devrinde (maksimum tork devri) motor yükü değiştirilerek yapılmıştır. İHE, konvertörün CO ve HC emisyonlarını dönüştürme verimini motorun stokiyometrik hava/yakıt oranından daha zengin çalıştığı koşullarda artışını sağlarken, NO emisyonunun dönüşümünü olumsuz etkilememiştir.
- 1 June 2022
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 25 (2) , 861-869
Buji İle Ateşlemeli Bir Motorda İkincil Hava Enjeksiyonunun Egzoz Emisyonları ve Katalitik Konvertör Verimine Etkisinin Deneysel Analizi
İçten yanmalı motorlarda gücün elde edilmesi yanma olayının bir sonucunun olması ve yanmanın belirli bir süre içerisinde gerçekleşmesi kirletici emisyonlarını kaçınılmaz yapmaktadır. Ancak emisyon kontrol yöntemleriyle bu durum kontrol altına alınmaya çalışılmaktadır. Bu çalışmada da tek nokta yakıt enjeksiyonuna sahip buji ile ateşlemeli motorda ikincil hava enjeksiyonunun (İHE) ve üç yollu katalitik konvertörün CO, HC ve NO emisyonlarına etkisi deneysel olarak incelenmiştir. Deneyler 1500-5000 rpm motor devri aralığında tam yükte ve 2500 rpm sabit motor devrinde (maksimum tork devri) motor yükü değiştirilerek yapılmıştır. İHE, konvertörün CO ve HC emisyonlarını dönüştürme verimini motorun stokiyometrik hava/yakıt oranından daha zengin çalıştığı koşullarda artışını sağlarken, NO emisyonunun dönüşümünü olumsuz etkilememiştir.
- 31 October 2021
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 41 (2) , 227-237
THE VARIATIONS OF THE EXHAUST EMISSIONS AT LOW AMBIENT TEMPERATURE FOR E10 AND M10 FUELED SI ENGINE
Biomass fuels are important alternatives to conventional energy sources such as petroleum-based fuels. Biomass fuels especially alcohols have been used in passenger cars. Alcohol blends with gasoline constitute a general use. Particularly, modification of the engine is not required when using at low rates, like gasohol. Gasohol consists of a mixture of gasoline and especially ethanol, and it contains generally 10 percent alcohol. This study deals with the effect of the usage of low alcohol containing (10% ethanol or 10% methanol) blends on the exhaust emissions caused by an SI engine in the 600 seconds of the engine’s operating period from the cold start-up. According to the experimental results, the leaning effect of alcohol on the emissions is clearer in the initial 150 seconds of the experiments. The engine-out CO emissions decreased on average 34.5% for E10 fuel and 44.8% for M10 fuel compared to unleaded gasoline. Also, in the first 150 seconds, an average reduction of 23.2% E10 fuel and 25% M10 was observed in HC. When it comes to the engine-out NO, there were no significant differences by fuel type. Besides, in the study, the tailpipe emissions and converter efficiency were examined by heating the catalytic converter without changing other experimental conditions. Emissions were significantly reduced in all fuels, while efficiency reached 100%, especially for CO emissions.
- 31 October 2021
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 41 (2) , 227-237
THE VARIATIONS OF THE EXHAUST EMISSIONS AT LOW AMBIENT TEMPERATURE FOR E10 AND M10 FUELED SI ENGINE
Biomass fuels are important alternatives to conventional energy sources such as petroleum-based fuels. Biomass fuels especially alcohols have been used in passenger cars. Alcohol blends with gasoline constitute a general use. Particularly, modification of the engine is not required when using at low rates, like gasohol. Gasohol consists of a mixture of gasoline and especially ethanol, and it contains generally 10 percent alcohol. This study deals with the effect of the usage of low alcohol containing (10% ethanol or 10% methanol) blends on the exhaust emissions caused by an SI engine in the 600 seconds of the engine’s operating period from the cold start-up. According to the experimental results, the leaning effect of alcohol on the emissions is clearer in the initial 150 seconds of the experiments. The engine-out CO emissions decreased on average 34.5% for E10 fuel and 44.8% for M10 fuel compared to unleaded gasoline. Also, in the first 150 seconds, an average reduction of 23.2% E10 fuel and 25% M10 was observed in HC. When it comes to the engine-out NO, there were no significant differences by fuel type. Besides, in the study, the tailpipe emissions and converter efficiency were examined by heating the catalytic converter without changing other experimental conditions. Emissions were significantly reduced in all fuels, while efficiency reached 100%, especially for CO emissions.
- 30 June 2021
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 5 (2) , 79-84
Effect of Profile Modification on Noise in Involute Gear Pair
Ensuring regular movement and power transmission in gear wheels is possible with a suitable tooth profile. Although involute profiles have a structure that can provide conjugate movement in accordance with the law of gearing, transmission errors that cause vibration and noise occur due to the flexibility of the elements in the gear system under dynamic conditions. Transmission errors occur depend-ing on many parameters from production to the oil and lubrication system. In this study, the vibration and noise state generated during transmission in gears were investigated in relation to geometric parameters. In the reference gear pair as-sumption, the noise levels were evaluated for the four cases created due to the change of different geometric parameters. The effect of profile modification on vibration and noise was addressed, and optimum profile modification parameters for the reference gear pair were analyzed with KISSsoft commercial software. The effects of geometric parameters and profile modification on noise level are shown in graphs. With the application of the Tip Relief method, a significant de-crease in the noise level has been observed.
- 30 June 2021
- Published by International Journal of Automotive Science and Technology in International Journal of Automotive Science And Technology
- Vol. 5 (2) , 79-84
Effect of Profile Modification on Noise in Involute Gear Pair
Ensuring regular movement and power transmission in gear wheels is possible with a suitable tooth profile. Although involute profiles have a structure that can provide conjugate movement in accordance with the law of gearing, transmission errors that cause vibration and noise occur due to the flexibility of the elements in the gear system under dynamic conditions. Transmission errors occur depend-ing on many parameters from production to the oil and lubrication system. In this study, the vibration and noise state generated during transmission in gears were investigated in relation to geometric parameters. In the reference gear pair as-sumption, the noise levels were evaluated for the four cases created due to the change of different geometric parameters. The effect of profile modification on vibration and noise was addressed, and optimum profile modification parameters for the reference gear pair were analyzed with KISSsoft commercial software. The effects of geometric parameters and profile modification on noise level are shown in graphs. With the application of the Tip Relief method, a significant de-crease in the noise level has been observed.
- 31 July 2020
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 8 (3) , 1948-1956
Tek Nokta Enjeksiyonlu Buji ile Ateşlemeli Bir Motorda Motor Devri ve Yükünün Motor Titreşimleri ve Gürültüye Etkisinin Deneysel İncelenmesi
Titreşim ve gürültü gerek günlük hayatta gerekse enerji üretim ve dönüşüm sistemlerinde istenmeyen etkilerdir. Bu çalışmada, motorun temel işletme parametrelerinden olan motor devri ve yükünün buji ile ateşlemeli bir motorda gürültü ve titreşime etkisi ele alınmıştır. Çalışma deneysel olarak iki aşamada gerçekleştirilmiştir. İlk olarak yüksüz motor şartlarında farklı motor devirlerinde deneyler yapılmıştır. İkinci aşamada sabit motor devrinde (1750 rpm) motor farklı yüklerde çalıştırılmıştır. Bu deney 2500 rpm motor devrinde de tekrarlanmıştır. Yapılan deneylerde elde edilen sonuçlar hem motor devrinin hem de motor yükünün titreşim ve gürültüyü arttırdığı görülmüştür.
- 31 July 2020
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 8 (3) , 1948-1956
Tek Nokta Enjeksiyonlu Buji ile Ateşlemeli Bir Motorda Motor Devri ve Yükünün Motor Titreşimleri ve Gürültüye Etkisinin Deneysel İncelenmesi
Titreşim ve gürültü gerek günlük hayatta gerekse enerji üretim ve dönüşüm sistemlerinde istenmeyen etkilerdir. Bu çalışmada, motorun temel işletme parametrelerinden olan motor devri ve yükünün buji ile ateşlemeli bir motorda gürültü ve titreşime etkisi ele alınmıştır. Çalışma deneysel olarak iki aşamada gerçekleştirilmiştir. İlk olarak yüksüz motor şartlarında farklı motor devirlerinde deneyler yapılmıştır. İkinci aşamada sabit motor devrinde (1750 rpm) motor farklı yüklerde çalıştırılmıştır. Bu deney 2500 rpm motor devrinde de tekrarlanmıştır. Yapılan deneylerde elde edilen sonuçlar hem motor devrinin hem de motor yükünün titreşim ve gürültüyü arttırdığı görülmüştür.