SSSimon Shindler

Simon Shindler

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Simon Shindler has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Heat transfer and mixing in initiated chemical vapor deposition analyzed by in situ gas composition sensing

    by Simon Shindler, Rong Yang

    When interpreting or modeling initiated chemical vapor deposition (iCVD) data, assumptions about vapor phase heat and mass transport are almost always required. However, empirically verifying such assumptions is difficult and rarely attempted. To address this gap, we utilize in situ gas composition measurements and heat transfer experiments to validate theoretical and computational models of the iCVD system. Gas composition is obtained using a Pirani pressure gauge, which we demonstrate to be effective in simple gas mixtures. Dimensional analysis shows that the parameter space describing heat and mass transport can be simplified significantly, with the degree of mixing in the reactor determined by the Peclet number (Pe) and the heat transfer regime determined by the Knudsen number (Kn). Multiphysics simulations indicate that the well-mixed assumption holds below Pe = 0.3. Residence time distribution measurements for argon and isopropanol support this conclusion. Next, we study heat transfer by measuring thermal diffusion from the filament at a range of pressures in argon and isopropanol. These data show that heat transfer is pressure independent above Kn = 0.4 and validates a first-principles model of heat transfer over the full range of Kn. To account for thermally driven pressure changes in batch mode, we define an “effective temperature” for the reactor and validate a model of it against pressure versus filament temperature data. Our findings provide a systematic framework for iCVD practitioners to estimate mixing and temperature profiles and assess the impact of design choices on both batch and continuous operation.

  • Analysis of the Vapor Phase Dynamics during iCVD: Free Radical Initiation by tert-Butyl Peroxide

    by Simon Shindler, Rong Yang

    While initiated chemical vapor deposition (iCVD) has been used in a wide range of fundamental and applied studies in the past two decades, little is known about the reactive vapor phase, leading to inconsistent treatment of the initiation process in the existing literature. Di-tert-butyl peroxide (TBPO) is commonly used as an initiator in iCVD by leveraging radical intermediates produced during thermal decomposition. Despite its widespread use, no models exist for TBPO decomposition in iCVD. To bridge this knowledge gap, we integrated the Pirani pressure gauge into the iCVD setup to measure the real-time vapor-phase composition in the reactor. After establishing the relationship between the Pirani gauge pressure and composition from batch data, we use it to quantify the fractional conversion of pure TBPO in the reactor in the continuous mode. We find that under iCVD conditions, TBPO fully decomposes to acetone and ethane following a first-order Arrhenius kinetics. This means that (i) the partial pressures of radicals are small (below the detection limit of the Pirani gauge) and (ii) there is a stoichiometric increase in the number of gas molecules in the reactor, which has not been accounted for in existing models. This causes the overestimation of monomer pressure, which is a key parameter in the current understanding of iCVD. We analyze the decomposition of TBPO in the presence of cyclohexyl methacrylate (CHMA) monomer suggesting that the monomer does not react appreciably in the vapor phase. To show how this model of the vapor phase is related to the deposition kinetics, we compare our data to the classical linear polymerization theory, which describes free radical polymerization of CHMA in solution and finds an acceptable fit. Notably, in Arrhenius plots of the deposition rate, there is a well-documented but unexplained decrease in the apparent activation energy at high filament temperature (>300 °C), which is predicted by our models.


  • Open Access

    Fluorine‐Free Amphiphilic Copolymers for Broad‐Spectrum Marine Biofouling Deterrence

    by Haonian Shu, Alexandra Khlyustova, Kwang‐Won Park, Shane Stafslien, Gyeongwan Kang, Pengyu Chen, Simon Shindler, Rong Yang

    Biofouling, the accumulation of living organisms on submerged surfaces, remains a critical challenge in marine and industrial settings. Amphiphilic coatings offer promising antifouling performance by presenting both hydrophilic and hydrophobic domains, but often rely on environmentally persistent perfluoroalkyl substances (PFAS). This study introduces a fluorine‐free amphiphilic copolymer synthesized via initiated Chemical Vapor Deposition (iCVD), incorporating 1,3,5,7‐tetramethyl‐1,3,5,7‐tetravinyl cyclotetrasiloxane (V4D4) as the hydrophobic component and pyridinium‐based zwitterions as the hydrophilic moiety. V4D4 enables an unprecedented conversion rate of pyridine to zwitterionic sulfobetaine, reaching 69.5% at a 240 nm depth into the film from a diffusion‐limited vapor derivatization reaction, pointing to the network flexibility afforded by V4D4. The coating reduces Pseudomonas aeruginosa attachment by over 90% compared to aluminum surfaces and decreases Cellulophaga lytica biofilm formation by 55% compared to a zwitterionic benchmark under dynamic flow. Against the model diatom Navicula incerta , it achieves 99.7% removal after water jetting, outperforming a commercial fouling‐release paint, Intersleek® 1100SR. The high fouling‐release performance is attributed to its low Young's modulus, promoting deformation under shear. Additionally, the coating exhibits chemical stability in alkaline conditions that degrade PFAS‐based counterparts. These findings present a durable, high‐performance, and environmentally responsible alternative to PFAS‐based amphiphilic copolymers as the next‐generation antifouling technologies.


  • Open Access

    Transtympanic delivery of V 2 O 5 nanowires with a tympanic-membrane penetrating peptide

    by Sophie S. Liu, Jiayan Lang, Shuxian Wen, Pengyu Chen, Haonian Shu, Simon Shindler, Wenjing Tang, Xiaojing Ma, Max D. Serota, Rong Yang

    Vanadium pentoxide (V 2 O 5 ) nanowires were modified with trans-tympanic peptides for enhanced trans-tympanic permeability. The as-modified nanowires retain haloperoxidase-like catalytic activities that can be harnessed to combat otitis media pathogens.


  • Prevention and characterization of thin film defects induced by contaminant aggregates in initiated chemical vapor deposition

    by Simon Shindler, Trevor Franklin, Rong Yang

    As initiated Chemical Vapor Deposition (iCVD) finds increasing application in precision industries like electronics and optics, defect prevention will become critical. While studies of non-ideal morphology exist in the iCVD literature, no studies investigate the role of defects. To address this knowledge gap, we show that the buildup of short-chain polymers or oligomers during normal operation of an iCVD reactor can lead to defects that compromise film integrity. We used atomic force microscopy to show that oligomer aggregates selectively prevented film growth, causing these hole-like defects. X-ray diffraction and optical microscopy demonstrated the crystallinity of the aggregates, pointing to a flat-on lamellar or mono-lamellar structure. To understand the origin of the aggregates, spectroscopic ellipsometry showed that samples exposed to the reactor consistently accrued low-volatility contaminants. X-ray photoelectron spectroscopy revealed material derived from polymerization in the contamination, while scanning electron microscopy showed the presence of defect-causing aggregates. We directly linked oligomeric/polymeric contamination with defect formation by showing an increased defect rate when a contaminant polymer was heated alongside the sample. Most importantly, we showed that starting a deposition at a high sample temperature (e.g., 50 °C) before reducing it to the desired setpoint (e.g., 9 °C) unilaterally prevented defects, providing a simple method to prevent defects with minimal impact on operations.


  • Hydrolysis of Poly(fluoroacrylate) Thin Films Synthesized from the Vapor Phase

    by Simon Shindler, Rong Yang

    The post-synthesis surface reaction of vapor-deposited polymer thin films is a promising technique in engineering heterogeneous surface chemistry. Because the existing research has neglected marginally reactive precursor films in preference of their highly reactive counterparts, our knowledge of kinetics and loss of film integrity during the reaction are limited. To address these limitations, we characterize hydrolysis of two fluoroacrylates, poly(1H,1H,2H,2H-perfluorooctyl acrylate) (pPFOA) and poly(2,2,3,4,4,4-hexafluorobutyl acrylate) (pHFBA), with sodium hydroxide using X-ray photoelectron spectroscopy. Without crosslinking with di(ethylene glycol)divinyl ether (DEGDVE) and grafting with trichlorovinyl silane, the films degrade rapidly during hydrolysis. An SN2 mechanism describes hydrolysis well, with rate constants of 0.0029 ± 0.0004 and 0.011 ± 0.001 L mol-1s-1 at 30 °C for p(PFOA-co-DEGDVE) and p(HFBA-co-DEGDVE), respectively. Our detailed study of hydrolysis kinetics of marginally reactive fluoroacrylates demonstrates the full capability and limitations of the post-synthesis reaction. Importantly, copolymers are characterized using a density correction new to polymer chemical vapor deposition.


  • A cascade nanozyme with antimicrobial effects against nontypeable Haemophilus influenzae

    by Xiaojing Ma, Jiayan Lang, Pengyu Chen, Wenjing Tang, Simon Shindler, Rong Yang

    A cascade nanozyme with glucose oxidase and haloperoxidase activities was designed and synthesized, which was shown to generate antiseptic HOBr from a ubiquitous non-ROS, O2. It successfully inhibited growth of a bacterial pathogen and its biofilm.