Türkan Börklü Budak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Türkan Börklü Budak has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Adella Myori Hardieka
Department of Chemistry, Faculty of Art and Science, Yıldız Technical University, 34220 İstanbul, Türkiye
2 shared publications - Beyza Moralı
Department of Chemistry, Faculty of Art and Science, Yıldız Technical University, 34220 İstanbul, Türkiye
1 shared publication - Fatma Ozcan
Yildiz Technical University, Faculty of Art and Science, Department of Chemistry, İstanbul, Türkiye
1 shared publication - Sevnur Keskin Dogruyol
Yildiz Technical University, Faculty of Art and Science, Department of Chemistry, İstanbul, Türkiye
1 shared publication
Latest Publications
- Open Access
Evaluation of the Removal of Basic Blue 3 and Basic Yellow 28 Textile Dyes from Aqueous Media Using Persea americana ‘Hass’ Avocado Peel
This study investigates the potential of Hass avocado peels as biosorbents for removing the cationic dyes BB3 and BY28 from aqueous solutions. The results demonstrate that agricultural waste can be effectively incorporated into sustainable, environmentally friendly wastewater treatment technologies. The adsorption parameters examined include adsorbent mass (0.1–1.1 g), dye concentration (5–50 mg/L), contact time (5–180 min), stirring speed (100–200 rpm), pH (4–10), and temperature (25–40 °C). UV-Vis spectrophotometric analyses show that the optimum conditions for BY28 removal are 0.3 g/50 mL adsorbent, 5 mg/L dye concentration, 30 min contact time, 200 rpm stirring speed, pH 7, and 40 °C, while those for BB3 are 1.1 g/50 mL adsorbent, 5 mg/L concentration, 45 min contact time, 150 rpm stirring speed, pH 7, and 40 °C. Under the optimized operating conditions, the maximum dye removal efficiencies were 88.24% for BY28 and 99.71% for BB3. This study demonstrates that agricultural waste can be converted into sustainable, reusable biosorbents for removing cationic dyes, thereby contributing to the development of environmentally friendly wastewater treatment technologies.
Open AccessEvaluation of the Removal of Basic Blue 3 and Basic Yellow 28 Textile Dyes from Aqueous Media Using Persea americana ‘Hass’ Avocado Peel
This study investigates the potential of Hass avocado peels as biosorbents for removing the cationic dyes BB3 and BY28 from aqueous solutions. The results demonstrate that agricultural waste can be effectively incorporated into sustainable, environmentally friendly wastewater treatment technologies. The adsorption parameters examined include adsorbent mass (0.1–1.1 g), dye concentration (5–50 mg/L), contact time (5–180 min), stirring speed (100–200 rpm), pH (4–10), and temperature (25–40 °C). UV-Vis spectrophotometric analyses show that the optimum conditions for BY28 removal are 0.3 g/50 mL adsorbent, 5 mg/L dye concentration, 30 min contact time, 200 rpm stirring speed, pH 7, and 40 °C, while those for BB3 are 1.1 g/50 mL adsorbent, 5 mg/L concentration, 45 min contact time, 150 rpm stirring speed, pH 7, and 40 °C. Under the optimized operating conditions, the maximum dye removal efficiencies were 88.24% for BY28 and 99.71% for BB3. This study demonstrates that agricultural waste can be converted into sustainable, reusable biosorbents for removing cationic dyes, thereby contributing to the development of environmentally friendly wastewater treatment technologies.
- Open Access
- 31 January 2026
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 38 (2) , 463-470
Study on Adsorption Efficiency of Low-Cost Hemp Seed Oil Cake (Cannabis sativa L.) as Adsorbent for the Removal of Reactive Black 5 Dye from Aqueous Solution
Driven by the need for sustainable and economical water treatment solutions, this study explores the use of agricultural byproduct adsorbents, specifically hemp seed oil cake (HSOC), for the removal of reactive black 5 (RB5) dye. Batch experiments identified the ideal conditions for the adsorption process, resulting in a maximum removal efficiency of 99.94%. The process, identified as spontaneous and exothermic through thermodynamic analysis, was most effective under the following conditions: an initial RB5 dye concentration of 10 mg/L, 1.5 g of HSOC adsorbent, a pH of 4 (acidic condition), 45 min of contact time, 100 rpm agitation and a temperature of 50 ºC. These results collectively affirm HSOC’s promise as a highly efficient, bio-based material for the remediation of dye-contaminated water.
- 31 January 2026
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 38 (2) , 463-470
Open AccessStudy on Adsorption Efficiency of Low-Cost Hemp Seed Oil Cake (Cannabis sativa L.) as Adsorbent for the Removal of Reactive Black 5 Dye from Aqueous Solution
Driven by the need for sustainable and economical water treatment solutions, this study explores the use of agricultural byproduct adsorbents, specifically hemp seed oil cake (HSOC), for the removal of reactive black 5 (RB5) dye. Batch experiments identified the ideal conditions for the adsorption process, resulting in a maximum removal efficiency of 99.94%. The process, identified as spontaneous and exothermic through thermodynamic analysis, was most effective under the following conditions: an initial RB5 dye concentration of 10 mg/L, 1.5 g of HSOC adsorbent, a pH of 4 (acidic condition), 45 min of contact time, 100 rpm agitation and a temperature of 50 ºC. These results collectively affirm HSOC’s promise as a highly efficient, bio-based material for the remediation of dye-contaminated water.
- Open Access
Comparison of the Removal of Synthetic Wastewater Samples Containing Basic Blue 3 Dye Using Electrochemical and Adsorption Methods
Water pollution, a significant environmental issue, is growing more urgent. This study evaluated the effectiveness of adsorption and electrocoagulation methods in removing Ba-sic Blue 3 (BB3), a common dye used in the textile industry, from water. For the adsorption process, linden tree leaves—often used for health benefits in existing literature—were employed, while in the electrocoagulation (EC) method, an aluminum electrode was used. The results show that the optimal conditions for adsorption were an initial BB3 concentration of 5 mg/L, 50 mL of 0.9 g Tilia L. adsorbent, 60 min, 180 rpm, 30 °C, and pH 10, achieving a removal efficiency of 99.21%. The optimal conditions for electrocoagulation were 1 L of 15 mg/L initial BB3, a current density of 2.64 mA/cm2, 15 mL of 0.2 M KCl, a reaction time of 90 min, a stirring speed of 100 rpm, and a pH of 10, resulting in a removal efficiency of 97.98%. The results indicate that linden leaves, a natural and sustainable material, showed a slightly higher removal percentage (99.21%) in the EC method over a shorter period (60 min). Conversely, the EC method also achieved a significant removal rate (97.98%, 90 min). In summary, both methods demonstrate strong BB3 removal capabilities and could help improve wastewater treatment processes.
Open AccessComparison of the Removal of Synthetic Wastewater Samples Containing Basic Blue 3 Dye Using Electrochemical and Adsorption Methods
Water pollution, a significant environmental issue, is growing more urgent. This study evaluated the effectiveness of adsorption and electrocoagulation methods in removing Ba-sic Blue 3 (BB3), a common dye used in the textile industry, from water. For the adsorption process, linden tree leaves—often used for health benefits in existing literature—were employed, while in the electrocoagulation (EC) method, an aluminum electrode was used. The results show that the optimal conditions for adsorption were an initial BB3 concentration of 5 mg/L, 50 mL of 0.9 g Tilia L. adsorbent, 60 min, 180 rpm, 30 °C, and pH 10, achieving a removal efficiency of 99.21%. The optimal conditions for electrocoagulation were 1 L of 15 mg/L initial BB3, a current density of 2.64 mA/cm2, 15 mL of 0.2 M KCl, a reaction time of 90 min, a stirring speed of 100 rpm, and a pH of 10, resulting in a removal efficiency of 97.98%. The results indicate that linden leaves, a natural and sustainable material, showed a slightly higher removal percentage (99.21%) in the EC method over a shorter period (60 min). Conversely, the EC method also achieved a significant removal rate (97.98%, 90 min). In summary, both methods demonstrate strong BB3 removal capabilities and could help improve wastewater treatment processes.
- Open Access
- 17 September 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 70 (9) , 550-558
Removal of Fe³⁺ ions from aqueous solutions using poly(methyl methacrylate)
Methyl methacrylate (MMA) monomer was synthesized using 2-pyrrolidinoacetonaphthone (MPY) as a photoinitiator, and the obtained PMMA was used as an adsorbent of Fe³⁺ ions. Under optimal conditions (0.2 g PMMA, 15 mg/L Fe³⁺, 40 min contact time, 30°C, pH 10, 150 rpm) 99.98% Fe³⁺ ions were removed from natural water samples. The obtained results indicate that UV-synthesized PMMA has the potential not only to remove Fe³⁺ but also other heavy metals and may constitute a sustainable solution for wastewater treatment.
- 17 September 2025
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 70 (9) , 550-558
Open AccessRemoval of Fe³⁺ ions from aqueous solutions using poly(methyl methacrylate)
Methyl methacrylate (MMA) monomer was synthesized using 2-pyrrolidinoacetonaphthone (MPY) as a photoinitiator, and the obtained PMMA was used as an adsorbent of Fe³⁺ ions. Under optimal conditions (0.2 g PMMA, 15 mg/L Fe³⁺, 40 min contact time, 30°C, pH 10, 150 rpm) 99.98% Fe³⁺ ions were removed from natural water samples. The obtained results indicate that UV-synthesized PMMA has the potential not only to remove Fe³⁺ but also other heavy metals and may constitute a sustainable solution for wastewater treatment.
- Open Access
Investigation of Removing Basic Yellow 28 and Basic Blue 3 Dyes from Water Using Mulberry Leaves (Morus nigra L.) and Assessment of Ultrasonic Effects
Many industries release untreated synthetic dye effluents into water bodies, harming ecosystems and human health. Therefore, an economical and sustainable solution for treating dye-contaminated water must be developed. In this study, mulberry leaves (Morus nigra L.), as a cost-effective and sustainable adsorbent, were prepared to remove Basic Yellow 28 (BY28) and Basic Blue 3 (BB3) cationic dyes from industrial dye wastewater using adsorption. Batch experiments with key variables such as initial dye concentration, adsorbent dosage, contact time, temperature, stirring speed, and pH were conducted to find optimal conditions. The effectiveness of mulberry leaves as an adsorbent after multiple regeneration cycles was examined. The adsorbent was characterized through various instrumental methods, including FTIR, SEM, XRD, and BET analysis. Adsorption performance was analyzed using the Langmuir and Freundlich isotherm models. The results showed that the mulberry leaf adsorbent best fits the Langmuir model, with R2 values of 0.999 for BY28 and 0.973 for BB3. The maximum adsorption capacities were 0.15 mg/g for BY28 and 7.19 mg/g for BB3, indicating their upper limits for dye uptake. The optimal conditions achieving removal efficiencies of over 99% were 1.5 g, 50 mL, 15 min, 180 rpm, and 10 mg/L at 30 °C for BY28 in neutral pH (7) and 1.5 g, 50 mL, 45 min, 100 rpm, and 30 mg/L at 40 °C for BB3 in basic pH (10). The regeneration of mulberry leaves as an adsorbent through acid treatment with 0.1 M HCl and 0.1 M CH3COOH solutions maintained a high performance, achieving up to 98% dye removal efficiency after two regeneration cycles. It has been observed that successful results can be achieved in terms of reusability. Additionally, the removals of BB3 and BY28 performed in an ultrasonic-bath-assisted environment successfully achieved removal efficiencies of 84.87% and 75.41%, respectively. According to the results, mulberry leaves can effectively be used in wastewater treatment to remove dyes, can be reused multiple times, and thus serve as an environmentally friendly and sustainable adsorbent.
Open AccessInvestigation of Removing Basic Yellow 28 and Basic Blue 3 Dyes from Water Using Mulberry Leaves (Morus nigra L.) and Assessment of Ultrasonic Effects
Many industries release untreated synthetic dye effluents into water bodies, harming ecosystems and human health. Therefore, an economical and sustainable solution for treating dye-contaminated water must be developed. In this study, mulberry leaves (Morus nigra L.), as a cost-effective and sustainable adsorbent, were prepared to remove Basic Yellow 28 (BY28) and Basic Blue 3 (BB3) cationic dyes from industrial dye wastewater using adsorption. Batch experiments with key variables such as initial dye concentration, adsorbent dosage, contact time, temperature, stirring speed, and pH were conducted to find optimal conditions. The effectiveness of mulberry leaves as an adsorbent after multiple regeneration cycles was examined. The adsorbent was characterized through various instrumental methods, including FTIR, SEM, XRD, and BET analysis. Adsorption performance was analyzed using the Langmuir and Freundlich isotherm models. The results showed that the mulberry leaf adsorbent best fits the Langmuir model, with R2 values of 0.999 for BY28 and 0.973 for BB3. The maximum adsorption capacities were 0.15 mg/g for BY28 and 7.19 mg/g for BB3, indicating their upper limits for dye uptake. The optimal conditions achieving removal efficiencies of over 99% were 1.5 g, 50 mL, 15 min, 180 rpm, and 10 mg/L at 30 °C for BY28 in neutral pH (7) and 1.5 g, 50 mL, 45 min, 100 rpm, and 30 mg/L at 40 °C for BB3 in basic pH (10). The regeneration of mulberry leaves as an adsorbent through acid treatment with 0.1 M HCl and 0.1 M CH3COOH solutions maintained a high performance, achieving up to 98% dye removal efficiency after two regeneration cycles. It has been observed that successful results can be achieved in terms of reusability. Additionally, the removals of BB3 and BY28 performed in an ultrasonic-bath-assisted environment successfully achieved removal efficiencies of 84.87% and 75.41%, respectively. According to the results, mulberry leaves can effectively be used in wastewater treatment to remove dyes, can be reused multiple times, and thus serve as an environmentally friendly and sustainable adsorbent.
- Open Access
Adsorption of Basic Yellow 28 and Basic Blue 3 Dyes from Aqueous Solution Using Silybum Marianum Stem as a Low-Cost Adsorbent
In the present study, the ability of an adsorbent (SLM Stem) obtained from the stem of the Silybum Marianum plant to treat wastewater containing the cationic dyes basic blue 3 (BB3) and basic yellow 28 (BY28) from aqueous solutions was investigated using a batch method. Then, the SLM Stem (SLM Stem-Natural) adsorbent was carbonized at different temperatures (200–900 °C) and the removal capacity of the products obtained for both dyes was examined again. The investigation continued with the product carbonized at 800 °C (SLM Stem-800 °C), the adsorbent with the highest removal capacity. The dyestuff removal studies were continued with the SLM Stem-Natural and SLM Stem-800 °C adsorbents because they had the highest removal values. The surface properties of these two adsorbents were investigated using IR, SEM, and XRD measurements. It was determined that the SLM Stem-Natural has mainly non-porous material, and the SLM Stem-800 °C has a microporous structure. The optimal values for various parameters, including adsorbent amount, initial dye solution concentration, contact time, temperature, pH, and agitation speed, were investigated for BY28 dye and were 0.05 g, 15 mg/L, 30 min, 40 °C, pH 6 and 100 rpm when SLM Stem-Natural adsorbent was used and, 0.15 g, 30 mg/L, 30 min, 40 °C, pH 10, and 150 rpm when SLM Stem-800 °C adsorbent was used. For BB3 dye, optimal parameter values of 0.20 g, 10 mg/L, 30 min, 25 °C, pH 7, and 100 rpm were obtained when SLM Stem-Natural adsorbent was used and 0.15 g, 15 mg/L, 40 min, 40 °C, pH 10, and 100 rpm when SLM Stem-800 °C adsorbent was used. The Langmuir isotherm described the adsorption process best, with a value of r2 = 0.9987. When SLM Stem-800 °C adsorbent was used for BY28 dye at 25 °C, the highest qm value in the Langmuir isotherm was 271.73 mg/g. When the study was repeated with actual water samples under optimum conditions, the highest removal for the BY28 dye was 99.9% in tap water with the SLM Stem-800 °C adsorbent. Furthermore, the reuse study showed the adsorbent’s efficiency even after three repetitions.
Open AccessAdsorption of Basic Yellow 28 and Basic Blue 3 Dyes from Aqueous Solution Using Silybum Marianum Stem as a Low-Cost Adsorbent
In the present study, the ability of an adsorbent (SLM Stem) obtained from the stem of the Silybum Marianum plant to treat wastewater containing the cationic dyes basic blue 3 (BB3) and basic yellow 28 (BY28) from aqueous solutions was investigated using a batch method. Then, the SLM Stem (SLM Stem-Natural) adsorbent was carbonized at different temperatures (200–900 °C) and the removal capacity of the products obtained for both dyes was examined again. The investigation continued with the product carbonized at 800 °C (SLM Stem-800 °C), the adsorbent with the highest removal capacity. The dyestuff removal studies were continued with the SLM Stem-Natural and SLM Stem-800 °C adsorbents because they had the highest removal values. The surface properties of these two adsorbents were investigated using IR, SEM, and XRD measurements. It was determined that the SLM Stem-Natural has mainly non-porous material, and the SLM Stem-800 °C has a microporous structure. The optimal values for various parameters, including adsorbent amount, initial dye solution concentration, contact time, temperature, pH, and agitation speed, were investigated for BY28 dye and were 0.05 g, 15 mg/L, 30 min, 40 °C, pH 6 and 100 rpm when SLM Stem-Natural adsorbent was used and, 0.15 g, 30 mg/L, 30 min, 40 °C, pH 10, and 150 rpm when SLM Stem-800 °C adsorbent was used. For BB3 dye, optimal parameter values of 0.20 g, 10 mg/L, 30 min, 25 °C, pH 7, and 100 rpm were obtained when SLM Stem-Natural adsorbent was used and 0.15 g, 15 mg/L, 40 min, 40 °C, pH 10, and 100 rpm when SLM Stem-800 °C adsorbent was used. The Langmuir isotherm described the adsorption process best, with a value of r2 = 0.9987. When SLM Stem-800 °C adsorbent was used for BY28 dye at 25 °C, the highest qm value in the Langmuir isotherm was 271.73 mg/g. When the study was repeated with actual water samples under optimum conditions, the highest removal for the BY28 dye was 99.9% in tap water with the SLM Stem-800 °C adsorbent. Furthermore, the reuse study showed the adsorbent’s efficiency even after three repetitions.
- Open Access
- 31 December 2022
- Published by Orclever Science and Research Group in The European Journal of Research and Development
- Vol. 2 (4) , 106-114
The Investigation Of Basic Yellow 28 Adsorption by Using Different Carbon Material
Accessible water resources on the earth's surface are decreasing day by day. For this reason, the treatment of wastewater released into the environment from different industrial areas is becoming a very important issue. In the present study, the removal of Basic Yellow 28 (BY28), one of the dyes used in the textile industry, from aqueous media using adsorption method was tested. Two different carbon based adsorbents; graphene nanoplatelets (graphene) and activated charcoal (activated carbon) were used as adsorbents. The optimum operating conditions were found as 0.004 g, 10 mL, 10 mg/L BY28, 10 minutes for activated charcoal and 0.05 g, 10 mL, 30 mg/L BY28, 15 minutes for graphene. As a result of the data obtained at optimum operating conditions; it was concluded that activated carbon can perform a more successful treatment than graphene.
- 31 December 2022
- Published by Orclever Science and Research Group in The European Journal of Research and Development
- Vol. 2 (4) , 106-114
Open AccessThe Investigation Of Basic Yellow 28 Adsorption by Using Different Carbon Material
Accessible water resources on the earth's surface are decreasing day by day. For this reason, the treatment of wastewater released into the environment from different industrial areas is becoming a very important issue. In the present study, the removal of Basic Yellow 28 (BY28), one of the dyes used in the textile industry, from aqueous media using adsorption method was tested. Two different carbon based adsorbents; graphene nanoplatelets (graphene) and activated charcoal (activated carbon) were used as adsorbents. The optimum operating conditions were found as 0.004 g, 10 mL, 10 mg/L BY28, 10 minutes for activated charcoal and 0.05 g, 10 mL, 30 mg/L BY28, 15 minutes for graphene. As a result of the data obtained at optimum operating conditions; it was concluded that activated carbon can perform a more successful treatment than graphene.
- 31 July 2020
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 8 (3) , 1794-1801
Investigation of Adsorption Studies of Different Arsenic Species Using the Diffusive Gradients in Thin Film (DGT) Technique
The amount of arsenic (As) in the earth increases every day and adversely affects the life of all living beings, including human health. Therefore, studies on the development of As determination methods are gradually gaining importance. The foundation of the Diffusive Gradients in Thin Film (DGT) technique addressed in this study is based on the diffusion process. The analyte to be determined passes through different layers in the DGT unit and reaches the adsorber gel layer. In the study presented, the gel obtained from iron (III) oxide (Fe2O3) was used as the adsorber layer. The use of the DGT technique in the amount determination of As(III) and As(V) species in the aqueous medium was examined and all the measurements performed during the experimental studies were observed to be made with an ICP-MS device. Different parameters were evaluated in terms of different pH values, ionic strength effects, gel layer thickness and the effects of the eluent materials and the most suitable working conditions were determined.
- 31 July 2020
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 8 (3) , 1794-1801
Investigation of Adsorption Studies of Different Arsenic Species Using the Diffusive Gradients in Thin Film (DGT) Technique
The amount of arsenic (As) in the earth increases every day and adversely affects the life of all living beings, including human health. Therefore, studies on the development of As determination methods are gradually gaining importance. The foundation of the Diffusive Gradients in Thin Film (DGT) technique addressed in this study is based on the diffusion process. The analyte to be determined passes through different layers in the DGT unit and reaches the adsorber gel layer. In the study presented, the gel obtained from iron (III) oxide (Fe2O3) was used as the adsorber layer. The use of the DGT technique in the amount determination of As(III) and As(V) species in the aqueous medium was examined and all the measurements performed during the experimental studies were observed to be made with an ICP-MS device. Different parameters were evaluated in terms of different pH values, ionic strength effects, gel layer thickness and the effects of the eluent materials and the most suitable working conditions were determined.
- 1 January 2013
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 25 (8) , 4207-4210
Removal of Heavy Metals from Wastewater Using Synthetic Ion Exchange Resin
- 1 January 2013
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 25 (8) , 4207-4210
Removal of Heavy Metals from Wastewater Using Synthetic Ion Exchange Resin