Hongwei Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hongwei Wang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Chengkai Jiang
1 shared publication- Miao Miao
Department of Earth and Space Sciences Southern University of Science and Technology Shenzhen China
1 shared publication - Mingming Jia
School of Civil Engineering, Harbin Institute of Technology, Harbin, China
1 shared publication - Shuangxi Zhang
Electronic Information College, Northwestern Polytechnical University, Xi’an 710129, China
1 shared publication - Xinding Fang
Southern University of Science and Technology 2 , Department of Earth and Space Sciences, Shenzhen, .
1 shared publication Xuan Yu
1 shared publication
Latest Publications
- 9 September 2023
- Published by Elsevier in Structures
- Vol. 57
Predictions of lateral deflection of square concrete-filled steel tube column under explosive impulse
- 9 September 2023
- Published by Elsevier in Structures
- Vol. 57
Predictions of lateral deflection of square concrete-filled steel tube column under explosive impulse
- Open Access
Influence of the Vertical Component of Yangbi Ground Motion on the Dynamic Response of RC Frame and Brick-Concrete Structure
An earthquake of magnitude 6.4 occurred in Yangbi County, Yunnan Province on 21 May 2021, with a focal depth of 8 km, and strong ground motion with vertical components was monitored by Yangbi station (53YBX). A total of 14,122 houses were damaged in Yangbi in the earthquake, and 232 of them collapsed. Vertical components of ground motions have been gained more attention for its effect on structure’s seismic response in epicenter or near-fault regions at present. Taking the three earthquake ground motions of Yangbi, Chi-Chi, and Loma Prieta as inputs, and modeling based on Perform-3D, this research carried out the seismic dynamic time history analysis of an RC (reinforced concrete) frame structure and a brick-concrete structure under both horizontal and vertical working conditions. The results showed that vertical components of the three ground motions had no evident impact on the top horizontal displacement and acceleration of the two types of structures. Among the three ground motions, the vertical component of Yangbi ground motion has largely influenced the top vertical displacement, acceleration, and axial force of the frame column bottom (or masonry wall bottom). The vertical component had different amplification effects on the axial pressure and the bending moment of a single column at the bottom of the RC frame structure, thus causing resonance amplification effect of the brick-concrete structure floors and amplifying the vertical acceleration of the top floor. In addition, it considerably increase the maximum axial tensile strain of masonry walls and the possibility of faster tensile failure of the brick-concrete structure. Influence of vertical ground motion on the bearing capacity of RC frame structure’s columns and the brick-concrete structure’s masonry walls should not be ignored. The results of the research may provide a reference for the earthquake-resistant design of building structures, especially the earthquake-resistant design considering the vertical seismic effect.
Open AccessInfluence of the Vertical Component of Yangbi Ground Motion on the Dynamic Response of RC Frame and Brick-Concrete Structure
An earthquake of magnitude 6.4 occurred in Yangbi County, Yunnan Province on 21 May 2021, with a focal depth of 8 km, and strong ground motion with vertical components was monitored by Yangbi station (53YBX). A total of 14,122 houses were damaged in Yangbi in the earthquake, and 232 of them collapsed. Vertical components of ground motions have been gained more attention for its effect on structure’s seismic response in epicenter or near-fault regions at present. Taking the three earthquake ground motions of Yangbi, Chi-Chi, and Loma Prieta as inputs, and modeling based on Perform-3D, this research carried out the seismic dynamic time history analysis of an RC (reinforced concrete) frame structure and a brick-concrete structure under both horizontal and vertical working conditions. The results showed that vertical components of the three ground motions had no evident impact on the top horizontal displacement and acceleration of the two types of structures. Among the three ground motions, the vertical component of Yangbi ground motion has largely influenced the top vertical displacement, acceleration, and axial force of the frame column bottom (or masonry wall bottom). The vertical component had different amplification effects on the axial pressure and the bending moment of a single column at the bottom of the RC frame structure, thus causing resonance amplification effect of the brick-concrete structure floors and amplifying the vertical acceleration of the top floor. In addition, it considerably increase the maximum axial tensile strain of masonry walls and the possibility of faster tensile failure of the brick-concrete structure. Influence of vertical ground motion on the bearing capacity of RC frame structure’s columns and the brick-concrete structure’s masonry walls should not be ignored. The results of the research may provide a reference for the earthquake-resistant design of building structures, especially the earthquake-resistant design considering the vertical seismic effect.
- 5 August 2020
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 45 (1) , 3-27
An analytical approach for cased borehole stress calculation in general anisotropic formations
Summary: We present an explicit analytical approach for calculating the distribution of stress around a circular cased borehole in a general anisotropic formation. This approach is developed based on a pure elastic cased borehole model, which can include multiple cemented concentric casing strings that are surrounded by a homogeneous anisotropic medium. The wall of the innermost casing is under the compression of borehole internal fluid pressure, and the formation can be subjected to arbitrary far‐field stresses. Every casing–cement boundary is assumed to be welded, so as the cement–formation boundary. The derived analytical solution can be applied to an arbitrary wellbore trajectory in an arbitrary anisotropic formation and is also applicable to degenerate isotropic formations. Accuracy and robustness of the analytical solution is validated through comparing its results with those calculated from the classical Kirsch solution for an isotropic example that has identical elastic properties for all materials and from a finite element method for an anisotropic cased borehole example.
- 5 August 2020
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 45 (1) , 3-27
An analytical approach for cased borehole stress calculation in general anisotropic formations
Summary: We present an explicit analytical approach for calculating the distribution of stress around a circular cased borehole in a general anisotropic formation. This approach is developed based on a pure elastic cased borehole model, which can include multiple cemented concentric casing strings that are surrounded by a homogeneous anisotropic medium. The wall of the innermost casing is under the compression of borehole internal fluid pressure, and the formation can be subjected to arbitrary far‐field stresses. Every casing–cement boundary is assumed to be welded, so as the cement–formation boundary. The derived analytical solution can be applied to an arbitrary wellbore trajectory in an arbitrary anisotropic formation and is also applicable to degenerate isotropic formations. Accuracy and robustness of the analytical solution is validated through comparing its results with those calculated from the classical Kirsch solution for an isotropic example that has identical elastic properties for all materials and from a finite element method for an anisotropic cased borehole example.