Amedeo Grimaldi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Amedeo Grimaldi has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Baricci
Politecnico di Milano
10 shared publications Andrea Casalegno
Politecnico di Milano
10 shared publications- Elena Colombo
Politecnico di Milano
8 shared publications - Francesco Verducci
Politecnico di Milano
5 shared publications Andrea Baricci
4 shared publicationsStefano De Antonellis
Politecnico di Milano
3 shared publications
Latest Publications
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02  (43) , 2191
Improved Air Humidification Stability in PEMFC: Experimental and Numerical Analysis of an Innovative Membrane Humidifier
Proton Exchange Membrane Fuel Cells (PEMFCs) are close to large-scale commercialization as an alternative power source for the automotive sector, particularly for the heavy-duty one. A major technological constraint affecting the widespread use of hydrogen fuel cell vehicles is the proper water management within the PEMFC stack, especially under dynamic loads. Operating the PEMFC under low humidity conditions reduces the proton conductivity of the proton exchange membrane, which results in a lower stack voltage and efficiency. In addition, the low relative humidity enhances chemical and mechanical degradation of the membrane, leading to a reduced lifetime of the stack. On the contrary, operation under excessively high relative humidity, with even liquid water (flooding), causes the lowering of the stack voltage. Effective humidification of the reactants ensures the cell operates efficiently and extends its lifetime. It has been highlighted in previous research works that the optimal value of the relative humidity of the air entering the stack is around 30%. External humidification using membrane humidifiers is attractive as they operate under passive conditions, requiring no external power, and are easily scalable to reach the desired humidity conditions. However, current commercial humidifiers are costly, due to expensive materials usage and un-optimized design. In addition, the steady-state worst case scenario, namely the high-power operation of the stack, is typically used for designing the humidifier. This approach leads to an oversized humidifier, with an impact on its cost and size. This work presents a novel approach where a single-unit membrane humidifier is equipped with a water vapor storage unit based on adsorption phenomenon, which improves the humidification system's dynamic performance by stabilizing the relative humidity of the air supplied to the humidifier, and consequently the relative humidity of the air fed to the PEMFC stack. This approach leads to a new way to design fuel cell humidifiers, shifting from water transport only (i.e. available humidifiers) to water transport coupled with water vapor storing capacity. Initially, a single-cell membrane humidifier is assembled by adopting 5 μm PFSA membrane with equivalent weight of 720 g mol -1 and equipped with plastic GDLs on both sides (water permeated through the selected membrane is represented in Figure1a ), and 3D printed flow fields. The device is tested in a vapor-to-vapor test bench to quantify water flux under diverse steady state conditions. Afterwards it is tested under dynamic conditions by using a variable RH profile at the wet inlet side. Performances of the optimized single-unit humidifier are evaluated and the RH profile at the dry outlet side is depicted and compared to the target value for relative humidity (30%). Experimental results are validated using a modelling tool adapted from prior works. Secondly, assessments are made on the sorption vapor storage unit. Regarding the integration of adsorption storage unit and membrane humidifier, the main configuration regards connecting a storage unit at the inlet of the wet side of the humidifier, after exiting the fuel cell stack. The storage unit should be based on adsorbent material with proper properties. A screening of commercial sorbents is performed by using a Dynamic Vapor Sorption (DVS) analyzer. Adsorption isotherms are measured at 50°C with varying relative humidity from 0-90% ( Figure1b ). Considering the typical operating conditions of the air streams flowing through the storage unit, the optimal material is selected. Lastly, the single-unit membrane humidifier integrated with the adsorption water storage is tested under dynamic conditions by using the same variable RH profile at the wet inlet side used for the humidifier alone. Performances of the innovative humidifier are evaluated and validated using a modelling tool adapted from prior works. The scalable design of the proposed humidifier ensures applicability for larger systems in heavy-duty fuel cell applications. This study provides critical insights into the development of next-generation humidifiers for heavy-duty fuel cell systems, paving the way for more durable and efficient hydrogen-powered transport solutions. Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02  (43) , 2191
Improved Air Humidification Stability in PEMFC: Experimental and Numerical Analysis of an Innovative Membrane Humidifier
Proton Exchange Membrane Fuel Cells (PEMFCs) are close to large-scale commercialization as an alternative power source for the automotive sector, particularly for the heavy-duty one. A major technological constraint affecting the widespread use of hydrogen fuel cell vehicles is the proper water management within the PEMFC stack, especially under dynamic loads. Operating the PEMFC under low humidity conditions reduces the proton conductivity of the proton exchange membrane, which results in a lower stack voltage and efficiency. In addition, the low relative humidity enhances chemical and mechanical degradation of the membrane, leading to a reduced lifetime of the stack. On the contrary, operation under excessively high relative humidity, with even liquid water (flooding), causes the lowering of the stack voltage. Effective humidification of the reactants ensures the cell operates efficiently and extends its lifetime. It has been highlighted in previous research works that the optimal value of the relative humidity of the air entering the stack is around 30%. External humidification using membrane humidifiers is attractive as they operate under passive conditions, requiring no external power, and are easily scalable to reach the desired humidity conditions. However, current commercial humidifiers are costly, due to expensive materials usage and un-optimized design. In addition, the steady-state worst case scenario, namely the high-power operation of the stack, is typically used for designing the humidifier. This approach leads to an oversized humidifier, with an impact on its cost and size. This work presents a novel approach where a single-unit membrane humidifier is equipped with a water vapor storage unit based on adsorption phenomenon, which improves the humidification system's dynamic performance by stabilizing the relative humidity of the air supplied to the humidifier, and consequently the relative humidity of the air fed to the PEMFC stack. This approach leads to a new way to design fuel cell humidifiers, shifting from water transport only (i.e. available humidifiers) to water transport coupled with water vapor storing capacity. Initially, a single-cell membrane humidifier is assembled by adopting 5 μm PFSA membrane with equivalent weight of 720 g mol -1 and equipped with plastic GDLs on both sides (water permeated through the selected membrane is represented in Figure1a ), and 3D printed flow fields. The device is tested in a vapor-to-vapor test bench to quantify water flux under diverse steady state conditions. Afterwards it is tested under dynamic conditions by using a variable RH profile at the wet inlet side. Performances of the optimized single-unit humidifier are evaluated and the RH profile at the dry outlet side is depicted and compared to the target value for relative humidity (30%). Experimental results are validated using a modelling tool adapted from prior works. Secondly, assessments are made on the sorption vapor storage unit. Regarding the integration of adsorption storage unit and membrane humidifier, the main configuration regards connecting a storage unit at the inlet of the wet side of the humidifier, after exiting the fuel cell stack. The storage unit should be based on adsorbent material with proper properties. A screening of commercial sorbents is performed by using a Dynamic Vapor Sorption (DVS) analyzer. Adsorption isotherms are measured at 50°C with varying relative humidity from 0-90% ( Figure1b ). Considering the typical operating conditions of the air streams flowing through the storage unit, the optimal material is selected. Lastly, the single-unit membrane humidifier integrated with the adsorption water storage is tested under dynamic conditions by using the same variable RH profile at the wet inlet side used for the humidifier alone. Performances of the innovative humidifier are evaluated and validated using a modelling tool adapted from prior works. The scalable design of the proposed humidifier ensures applicability for larger systems in heavy-duty fuel cell applications. This study provides critical insights into the development of next-generation humidifiers for heavy-duty fuel cell systems, paving the way for more durable and efficient hydrogen-powered transport solutions. Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02  (41) , 2000
Modeling Analysis of PEMFC Under Heavy-Duty Conditions: Impact of Radical Scavenger Transport on Performance Ageing and Identification of an Innovative Material-Based Mitigation Strategy
The durability of Polymer Electrolyte Membrane Fuel Cells (PEMFC) is a crucial factor for enhancing their competitiveness in the heavy-duty sector. In this sense, the cathode catalyst layer (CCL) and the polymer electrolyte membrane (PEM) represent the two most critical components of the stack. To mitigate the chemical degradation of the membrane, radical scavenger, such as cerium (Ce) ions, are typically adopted in PEMFC [1]. However, as shown recently in the literature [2,3], during real operation they migrate in the in-plane direction driven by concentration and potential gradients losing their scavenging efficacy and introducing additional performance loss. Therefore, it is essential to fully understand the major degradation mechanisms and assess their impact on the performance and lifetime of the technology. Accelerated stress tests (ASTs) are generally adopted with the aim of accelerating the characterization of durable materials by mimicking the main ageing mechanisms occurring during real-world operation. However, no protocols are already consolidated for heavy-duty applications. In this scenario, based on vehicle data from the IMMORTAL project [4], ad-hoc simulations were carried out by a 1+1D PEMFC stack model [5] to identify voltage transitions and holding times at both low and high power. The modelling analysis resulted in the heavy-duty AST protocol shown in Figure 1(a), which is characterized by an acceleration factor equal to 6. The ageing heterogeneity over the fuel cell area was studied by means of a segmented cell hardware whose active area was divided in 5 different portions and which adopts a counterflow configuration. Furthermore, an innovative model framework, coupling a 1+1D PEMFC performance model [5] with a semi-empirical electrocatalyst active surface area (ECSA) loss model and a 1D in-plane cerium transport model, was developed to better understand the drivers responsible for the experimentally observed performance ageing and to propose ad-hoc mitigation strategies. After 1100 cycles, i.e. 5000 operating hours, the 18% of the initial ECSA is lost (Figure 1(b)). Moreover, as revealed by both model simulations and a x-ray fluorescence (XRF) analysis (Figure 1(c)), after 1100 cycles of the heavy-duty AST protocol, a significant in-plane Ce redistribution was observed, with an accumulation at air inlet and outlet regions and a depletion in the middle regions of the cell. Since Ce mobility negatively affects both PEMFC lifetime and performance, decreasing protonic conductivity [1] and oxygen diffusion in CCL [2], it is crucial to stabilize it within the membrane for as long as possible. For this purpose, the above-mentioned model framework was used, first, to identify the material properties that mostly affect Ce transport and, later, to design an innovative material-based solution able to significantly limit the mobility of radical scavenger in the in-plane direction. Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02  (41) , 2000
Modeling Analysis of PEMFC Under Heavy-Duty Conditions: Impact of Radical Scavenger Transport on Performance Ageing and Identification of an Innovative Material-Based Mitigation Strategy
The durability of Polymer Electrolyte Membrane Fuel Cells (PEMFC) is a crucial factor for enhancing their competitiveness in the heavy-duty sector. In this sense, the cathode catalyst layer (CCL) and the polymer electrolyte membrane (PEM) represent the two most critical components of the stack. To mitigate the chemical degradation of the membrane, radical scavenger, such as cerium (Ce) ions, are typically adopted in PEMFC [1]. However, as shown recently in the literature [2,3], during real operation they migrate in the in-plane direction driven by concentration and potential gradients losing their scavenging efficacy and introducing additional performance loss. Therefore, it is essential to fully understand the major degradation mechanisms and assess their impact on the performance and lifetime of the technology. Accelerated stress tests (ASTs) are generally adopted with the aim of accelerating the characterization of durable materials by mimicking the main ageing mechanisms occurring during real-world operation. However, no protocols are already consolidated for heavy-duty applications. In this scenario, based on vehicle data from the IMMORTAL project [4], ad-hoc simulations were carried out by a 1+1D PEMFC stack model [5] to identify voltage transitions and holding times at both low and high power. The modelling analysis resulted in the heavy-duty AST protocol shown in Figure 1(a), which is characterized by an acceleration factor equal to 6. The ageing heterogeneity over the fuel cell area was studied by means of a segmented cell hardware whose active area was divided in 5 different portions and which adopts a counterflow configuration. Furthermore, an innovative model framework, coupling a 1+1D PEMFC performance model [5] with a semi-empirical electrocatalyst active surface area (ECSA) loss model and a 1D in-plane cerium transport model, was developed to better understand the drivers responsible for the experimentally observed performance ageing and to propose ad-hoc mitigation strategies. After 1100 cycles, i.e. 5000 operating hours, the 18% of the initial ECSA is lost (Figure 1(b)). Moreover, as revealed by both model simulations and a x-ray fluorescence (XRF) analysis (Figure 1(c)), after 1100 cycles of the heavy-duty AST protocol, a significant in-plane Ce redistribution was observed, with an accumulation at air inlet and outlet regions and a depletion in the middle regions of the cell. Since Ce mobility negatively affects both PEMFC lifetime and performance, decreasing protonic conductivity [1] and oxygen diffusion in CCL [2], it is crucial to stabilize it within the membrane for as long as possible. For this purpose, the above-mentioned model framework was used, first, to identify the material properties that mostly affect Ce transport and, later, to design an innovative material-based solution able to significantly limit the mobility of radical scavenger in the in-plane direction. Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02  (43) , 2189
Physically Consistent Dynamic Modeling of PEM Fuel Cell Systems for Heavy-Duty Applications
In recent years, Proton Exchange Membrane Fuel Cells (PEMFCs) have gained increasing attention as a commercial option for light-duty vehicles and a promising solution for heavy-duty applications, where system design remains an active area of research 1 . Ensuring the efficient and durable operation of PEMFCs requires a comprehensive understanding of the local operating conditions within the membrane-electrode assembly (MEA). Effective numerical modelling is crucial for unravelling the complexities of local heterogeneities arising from interactions among different system components. However, there is a need for models that are both computationally efficient and physically consistent. This study develops a detailed physical model of a fuel cell system based on a typical system architecture, with a primary focus on the PEMFC stack. The model employs a 1+1D multiphase, dynamic, non-isothermal approach based on previous works 2 . It accounts for mass dynamics in channels and gas diffusion layers, as well as membrane hydration and dehydration mechanisms, incorporating the impact of two platinum oxides species on oxygen reduction reaction (ORR) kinetics 3 . Additionally, air and hydrogen feed subsystems are modelled alongside the thermal management system, which plays a critical role in heavy-duty applications. The governing equations are implemented in the MATLAB Simulink environment using Simscape libraries, significantly reducing computational time, by at least a factor of 30, compared to an in-house model developed purely in Simulink 2 . This improvement enables faster-than-real-time simulation capability. The PEMFC system model, as visible in Figure 1(a), along with control strategies, is calibrated and validated using experimental data from an online database provided by the Argonne National Laboratory, based on a commercial light-duty vehicle 4 . Further validation is performed using experimental data obtained from a heavy-duty protocol, developed within the Italian project PERMANENT, on a five-segment single-cell PEMFC hardware, shown in Figure 1(b). A reference layout for the heavy-duty fuel cell system is selected based on publicly available data, and its dynamic performance is analysed under representative driving cycle conditions. A sensitivity analysis is conducted to evaluate the impact of component design and operational strategies, with a particular focus on the thermal management system (TMS) and its control, examining their influence on local operating conditions within the MEA and their subsequent impact on durability, exploiting a semi-empirical catalyst durability model 5 . The study investigates how TMS configurations affect fuel cell performance and durability, once defined the extent of hybridization level within the energy management system. References B. James et al., Heavy-Duty Fuel Cell System Cost – 2023 , p. 1–12, (2024) https://www.hydrogen.energy.gov/docs/hydrogenprogramlibraries/pdfs/review24/24004-hd-fuel-cell-system-cost-2023.pdf?sfvrsn=70ff384f_3. F. Verducci, A. Grimaldi, E. Colombo, A. Casalegno, and A. Baricci, Renew. Energy , 234, 121194 (2024) https://linkinghub.elsevier.com/retrieve/pii/S096014812401262X. T. Jahnke, A. Baricci, C. Rabissi, and A. Casalegno, J. Electrochem. Soc. , 167, 149001 (2020) https://iopscience.iop.org/article/10.1149/1945-7111/abbfda. H. Lohse-Busch et al., Technology Assessment Of A Fuel Cell Vehicle: 2017 Toyota Mirai , Argonne, IL (United States), (2018) http://www.osti.gov/servlets/purl/1463251/. A. Grimaldi, F. Verducci, E. Colombo, A. Casalegno, and A. Baricci, ECS Meet. Abstr. , MA2023-02, 1703–1703 (2023) https://dx.doi.org/10.1149/MA2023-02371703mtgabs. Figure 1
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02  (43) , 2189
Physically Consistent Dynamic Modeling of PEM Fuel Cell Systems for Heavy-Duty Applications
In recent years, Proton Exchange Membrane Fuel Cells (PEMFCs) have gained increasing attention as a commercial option for light-duty vehicles and a promising solution for heavy-duty applications, where system design remains an active area of research 1 . Ensuring the efficient and durable operation of PEMFCs requires a comprehensive understanding of the local operating conditions within the membrane-electrode assembly (MEA). Effective numerical modelling is crucial for unravelling the complexities of local heterogeneities arising from interactions among different system components. However, there is a need for models that are both computationally efficient and physically consistent. This study develops a detailed physical model of a fuel cell system based on a typical system architecture, with a primary focus on the PEMFC stack. The model employs a 1+1D multiphase, dynamic, non-isothermal approach based on previous works 2 . It accounts for mass dynamics in channels and gas diffusion layers, as well as membrane hydration and dehydration mechanisms, incorporating the impact of two platinum oxides species on oxygen reduction reaction (ORR) kinetics 3 . Additionally, air and hydrogen feed subsystems are modelled alongside the thermal management system, which plays a critical role in heavy-duty applications. The governing equations are implemented in the MATLAB Simulink environment using Simscape libraries, significantly reducing computational time, by at least a factor of 30, compared to an in-house model developed purely in Simulink 2 . This improvement enables faster-than-real-time simulation capability. The PEMFC system model, as visible in Figure 1(a), along with control strategies, is calibrated and validated using experimental data from an online database provided by the Argonne National Laboratory, based on a commercial light-duty vehicle 4 . Further validation is performed using experimental data obtained from a heavy-duty protocol, developed within the Italian project PERMANENT, on a five-segment single-cell PEMFC hardware, shown in Figure 1(b). A reference layout for the heavy-duty fuel cell system is selected based on publicly available data, and its dynamic performance is analysed under representative driving cycle conditions. A sensitivity analysis is conducted to evaluate the impact of component design and operational strategies, with a particular focus on the thermal management system (TMS) and its control, examining their influence on local operating conditions within the MEA and their subsequent impact on durability, exploiting a semi-empirical catalyst durability model 5 . The study investigates how TMS configurations affect fuel cell performance and durability, once defined the extent of hybridization level within the energy management system. References B. James et al., Heavy-Duty Fuel Cell System Cost – 2023 , p. 1–12, (2024) https://www.hydrogen.energy.gov/docs/hydrogenprogramlibraries/pdfs/review24/24004-hd-fuel-cell-system-cost-2023.pdf?sfvrsn=70ff384f_3. F. Verducci, A. Grimaldi, E. Colombo, A. Casalegno, and A. Baricci, Renew. Energy , 234, 121194 (2024) https://linkinghub.elsevier.com/retrieve/pii/S096014812401262X. T. Jahnke, A. Baricci, C. Rabissi, and A. Casalegno, J. Electrochem. Soc. , 167, 149001 (2020) https://iopscience.iop.org/article/10.1149/1945-7111/abbfda. H. Lohse-Busch et al., Technology Assessment Of A Fuel Cell Vehicle: 2017 Toyota Mirai , Argonne, IL (United States), (2018) http://www.osti.gov/servlets/purl/1463251/. A. Grimaldi, F. Verducci, E. Colombo, A. Casalegno, and A. Baricci, ECS Meet. Abstr. , MA2023-02, 1703–1703 (2023) https://dx.doi.org/10.1149/MA2023-02371703mtgabs. Figure 1
- Open Access
- 5 December 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 629
In-plane redistribution of radical scavenger during PEMFC real-world automotive operation and impact on catalyst-layer local oxygen transport resistance
- 5 December 2024
- Published by Elsevier in Journal of Power Sources
- Vol. 629
Open AccessIn-plane redistribution of radical scavenger during PEMFC real-world automotive operation and impact on catalyst-layer local oxygen transport resistance
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02  (44) , 2981
Modeling Analysis of the Impact of Platinum Oxides and Cerium Ion Migration on PEMFC Performance and Degradation Under a Realistic Driving Cycle
The sluggish oxygen reduction reaction (ORR) kinetics represents the major source of efficiency loss in a Proton Exchange Membrane Fuel Cell (PEMFC) [1]. In the potential range where fuel cells operate, several platinum (Pt) oxide species form on the catalyst surface [2]. Their formation and reduction is a dynamic process which strongly influences ORR activity and the loss of electrocatalyst active surface area (ECSA) [3]. PEMFC performance and durability are also significantly affected by Cerium (Ce) ions which, under typical operating conditions, are known to migrate through the polymer electrolyte membrane (PEM) and the catalyst layers (CLs) driven by concentration and potential gradients [4]. Such mobility reduces scavenging efficacy, thus accelerating PEM degradation. Moreover, it affects cell performance since the progressive build-up, during normal fuel cell operation, of Ce ions into the cathode CL is found to decrease proton conductivity [5] and hinder oxygen diffusion through the ionomer film [4], as highlighted by the most recent literature. In this scenario, a 1+1D multiphase dynamic non isothermal PEMFC model of performance is developed [6]: the close relationship between ORR reaction and Pt oxide dynamics is investigated by modeling oxides formation/reduction with a four-step oxidation mechanism which involves three different types of oxide species. Furthermore, based on the work of [2], the effects of ionomer sulfonate groups adsorption onto platinum surface and of local relative humidity are also included in the ORR kinetics. As visible in Figure 1(a), the proposed ORR formulation allows to properly capture cell voltage dynamics under the operating conditions of the automotive ID-FAST cycle [7]. The PEMFC model of performance also accounts for Ce ions mobility, both in the along-the-channel and through-the-membrane directions: for this purpose, a Nernst-Planck equation is adopted, where the diffusivity and migration coefficients are properly calibrated and validated (Figure 1(b)) by reproducing the Ce ions migration profiles reported in the literature for different current density [5]. Lastly, the 1+1D multiphase dynamic non isothermal PEMFC model is coupled with a physical-based 0D model of platinum degradation [3]. The presented model framework is validated on experimental data gathered on a segmented hardware and representative of 600 cycles in the low power conditions of the automotive ID-FAST driving cycle load protocol [7]: as visible in Figure 1(c), the 67% of the initial ECSA is lost. Succeeding in the prediction, this modelling structure aspires to provide critical information for the development of proper mitigation strategies aimed at extending the lifetime of PEMFC stacks. This work received support from the Italian government Progetto PERMANENT - BANDO MITE PNRR Missione 2 Investimento 3.5 A - RSH2A_0O0012. [1] H.A. Gasteiger et al., Activity benchmarks and requirements for Pt, Pt-alloy, and non-Pt oxygen reduction catalysts for PEMFCs, Appl. Catal. B Environ. 56 (2005) 9–35. https://doi.org/10.1016/j.apcatb.2004.06.021. [2] A. Kongkanand et al., Platinum Surface Oxide and Oxygen Reduction Reaction Kinetics during Transient Fuel Cell Operation, J. Electrochem. Soc. 170 (2023) 094506. https://doi.org/10.1149/1945-7111/acfbbb. [3] E. Colombo, Understanding and mitigating degradation of PEMFC caused by real automotive operation, (2023). https://hdl.handle.net/2027.42/155288. [4] A.M. Baker et al., Cerium Ion Mobility and Diffusivity Rates in Perfluorosulfonic Acid Membranes Measured via Hydrogen Pump Operation, J. Electrochem. Soc. 164 (2017) F1272–F1278. https://doi.org/10.1149/2.1221712jes. [5] V.M. Ehlinger et al., Modeling proton-exchange-membrane fuel cell performance/degradation tradeoffs with chemical scavengers, JPhys Energy. 2 (2020). https://doi.org/10.1088/2515-7655/abb194. [6] F. Verducci et al., Dynamic Modeling of Polymer Electrolyte Membrane Fuel Cells Under Real-World Automotive Driving Cycle with Experimental Validation on Segmented Single Cell, Renew. Energy. (Currently under review). [7] E. Colombo et al., PEMFC performance decay during real-world automotive operation: Evincing degradation mechanisms and heterogeneity of ageing, J. Power Sources. 553 (2023) 232246. https://doi.org/10.1016/j.jpowsour.2022.232246. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02  (44) , 2981
Modeling Analysis of the Impact of Platinum Oxides and Cerium Ion Migration on PEMFC Performance and Degradation Under a Realistic Driving Cycle
The sluggish oxygen reduction reaction (ORR) kinetics represents the major source of efficiency loss in a Proton Exchange Membrane Fuel Cell (PEMFC) [1]. In the potential range where fuel cells operate, several platinum (Pt) oxide species form on the catalyst surface [2]. Their formation and reduction is a dynamic process which strongly influences ORR activity and the loss of electrocatalyst active surface area (ECSA) [3]. PEMFC performance and durability are also significantly affected by Cerium (Ce) ions which, under typical operating conditions, are known to migrate through the polymer electrolyte membrane (PEM) and the catalyst layers (CLs) driven by concentration and potential gradients [4]. Such mobility reduces scavenging efficacy, thus accelerating PEM degradation. Moreover, it affects cell performance since the progressive build-up, during normal fuel cell operation, of Ce ions into the cathode CL is found to decrease proton conductivity [5] and hinder oxygen diffusion through the ionomer film [4], as highlighted by the most recent literature. In this scenario, a 1+1D multiphase dynamic non isothermal PEMFC model of performance is developed [6]: the close relationship between ORR reaction and Pt oxide dynamics is investigated by modeling oxides formation/reduction with a four-step oxidation mechanism which involves three different types of oxide species. Furthermore, based on the work of [2], the effects of ionomer sulfonate groups adsorption onto platinum surface and of local relative humidity are also included in the ORR kinetics. As visible in Figure 1(a), the proposed ORR formulation allows to properly capture cell voltage dynamics under the operating conditions of the automotive ID-FAST cycle [7]. The PEMFC model of performance also accounts for Ce ions mobility, both in the along-the-channel and through-the-membrane directions: for this purpose, a Nernst-Planck equation is adopted, where the diffusivity and migration coefficients are properly calibrated and validated (Figure 1(b)) by reproducing the Ce ions migration profiles reported in the literature for different current density [5]. Lastly, the 1+1D multiphase dynamic non isothermal PEMFC model is coupled with a physical-based 0D model of platinum degradation [3]. The presented model framework is validated on experimental data gathered on a segmented hardware and representative of 600 cycles in the low power conditions of the automotive ID-FAST driving cycle load protocol [7]: as visible in Figure 1(c), the 67% of the initial ECSA is lost. Succeeding in the prediction, this modelling structure aspires to provide critical information for the development of proper mitigation strategies aimed at extending the lifetime of PEMFC stacks. This work received support from the Italian government Progetto PERMANENT - BANDO MITE PNRR Missione 2 Investimento 3.5 A - RSH2A_0O0012. [1] H.A. Gasteiger et al., Activity benchmarks and requirements for Pt, Pt-alloy, and non-Pt oxygen reduction catalysts for PEMFCs, Appl. Catal. B Environ. 56 (2005) 9–35. https://doi.org/10.1016/j.apcatb.2004.06.021. [2] A. Kongkanand et al., Platinum Surface Oxide and Oxygen Reduction Reaction Kinetics during Transient Fuel Cell Operation, J. Electrochem. Soc. 170 (2023) 094506. https://doi.org/10.1149/1945-7111/acfbbb. [3] E. Colombo, Understanding and mitigating degradation of PEMFC caused by real automotive operation, (2023). https://hdl.handle.net/2027.42/155288. [4] A.M. Baker et al., Cerium Ion Mobility and Diffusivity Rates in Perfluorosulfonic Acid Membranes Measured via Hydrogen Pump Operation, J. Electrochem. Soc. 164 (2017) F1272–F1278. https://doi.org/10.1149/2.1221712jes. [5] V.M. Ehlinger et al., Modeling proton-exchange-membrane fuel cell performance/degradation tradeoffs with chemical scavengers, JPhys Energy. 2 (2020). https://doi.org/10.1088/2515-7655/abb194. [6] F. Verducci et al., Dynamic Modeling of Polymer Electrolyte Membrane Fuel Cells Under Real-World Automotive Driving Cycle with Experimental Validation on Segmented Single Cell, Renew. Energy. (Currently under review). [7] E. Colombo et al., PEMFC performance decay during real-world automotive operation: Evincing degradation mechanisms and heterogeneity of ageing, J. Power Sources. 553 (2023) 232246. https://doi.org/10.1016/j.jpowsour.2022.232246. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02  (44) , 3070
Hydrogen Limiting Current Test Diagnostic Tool for Analyzing PEMFC Durability in Accelerated Stress Tests
The durability of Polymer Electrolyte Membrane Fuel Cells (PEMFC) is a crucial factor for enhancing their competitiveness in the heavy-duty vehicle sector thus it is essential to assess the impact of the major degradation mechanisms on the performance and lifetime of the technology. To this end, accelerated stress tests have been standardized over the years with the aim of expediting the development of durable materials and being able to evaluate the durability in MEA. In this framework, it is extremely important to be able to separate different sources of voltage loss. Specifically, the degradation of mass transfer loss is extremely important because impacts the maximum power density available, efficiency and thermal management of the stack. Mass transfer loss is correlated at the material level, to the loss in electrocatalyst active surface (ECSA) being a consequence of the limitations in oxygen transport across the ionomer thin film. In this work mass transfer degradation is analyzed by ASTs that accelerate real-world ageing [1]. In this work, in addition to standard diagnostic tools, hydrogen limiting current test are investigated. Previous work reported that using hydrogen as reacting gas for limiting current test can give additional information on the sources of mass transfer loss compared to oxygen, specifically information on the ionomer thin film resistance [2]. In this work, limiting current tests were carried out as diagnostic tools during ASTs for electrocatalyst durability and novel ASTs that better mimick real-world vehicle operation within the IDFAST H2020 project and in the Italian project PERMANENT to investigate the degradation [2]. Correlation between mass transfer resistance in ionomer between oxygen and hydrogen limiting current test is found. Additional effects in the high potential region are observed and attributed to platinum oxide formation by means of a 1D MEA model that is adopted to investigate this effect. [1] Spingler F.B., Phillips A., Schuler T., Tucker M.C., Weber A.Z. (2017) International Journal of Hydrogen Energy, 13960-13969 [2] Colombo E., Baricci A., Mora D., Guetaz L., Casalegno A., (2023) Journal of Power Sources, 580 , art. no. 233376
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02  (44) , 3070
Hydrogen Limiting Current Test Diagnostic Tool for Analyzing PEMFC Durability in Accelerated Stress Tests
The durability of Polymer Electrolyte Membrane Fuel Cells (PEMFC) is a crucial factor for enhancing their competitiveness in the heavy-duty vehicle sector thus it is essential to assess the impact of the major degradation mechanisms on the performance and lifetime of the technology. To this end, accelerated stress tests have been standardized over the years with the aim of expediting the development of durable materials and being able to evaluate the durability in MEA. In this framework, it is extremely important to be able to separate different sources of voltage loss. Specifically, the degradation of mass transfer loss is extremely important because impacts the maximum power density available, efficiency and thermal management of the stack. Mass transfer loss is correlated at the material level, to the loss in electrocatalyst active surface (ECSA) being a consequence of the limitations in oxygen transport across the ionomer thin film. In this work mass transfer degradation is analyzed by ASTs that accelerate real-world ageing [1]. In this work, in addition to standard diagnostic tools, hydrogen limiting current test are investigated. Previous work reported that using hydrogen as reacting gas for limiting current test can give additional information on the sources of mass transfer loss compared to oxygen, specifically information on the ionomer thin film resistance [2]. In this work, limiting current tests were carried out as diagnostic tools during ASTs for electrocatalyst durability and novel ASTs that better mimick real-world vehicle operation within the IDFAST H2020 project and in the Italian project PERMANENT to investigate the degradation [2]. Correlation between mass transfer resistance in ionomer between oxygen and hydrogen limiting current test is found. Additional effects in the high potential region are observed and attributed to platinum oxide formation by means of a 1D MEA model that is adopted to investigate this effect. [1] Spingler F.B., Phillips A., Schuler T., Tucker M.C., Weber A.Z. (2017) International Journal of Hydrogen Energy, 13960-13969 [2] Colombo E., Baricci A., Mora D., Guetaz L., Casalegno A., (2023) Journal of Power Sources, 580 , art. no. 233376
- Open Access
- 19 September 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 95, 1299-1315
Experimental investigation on the effect of channel geometry on performance heterogeneity in hydrogen PEM fuel cell
- 19 September 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 95, 1299-1315
Open AccessExperimental investigation on the effect of channel geometry on performance heterogeneity in hydrogen PEM fuel cell
- Open Access
- 14 August 2024
- Published by Elsevier in Renewable Energy
- Vol. 234
Dynamic modeling of polymer electrolyte membrane fuel cells under real-world automotive driving cycle with experimental validation on segmented single cell
- 14 August 2024
- Published by Elsevier in Renewable Energy
- Vol. 234
Open AccessDynamic modeling of polymer electrolyte membrane fuel cells under real-world automotive driving cycle with experimental validation on segmented single cell
- Open Access
Computational Fluid Dynamic Investigation of Local Flow-Field Conditions in Lab Polymer Electrolyte Membrane Fuel Cells to Identify Degradation Stressors and Performance Enhancers
The use of polymer electrolyte membrane (PEM) fuel cells as an alternative to internal combustion engines can significantly contribute to the decarbonization of the transport sector, especially for heavy-duty applications. However, degradation is still an issue for this type of component, affecting their durability and performance. In this scenario, a detailed analysis of the anodic and cathodic distributors’ flow-field geometry may help to identify some local stressors that trigger the degradation mechanism, such as local hot spots and reactants not having a uniform distribution. A computational fluid dynamic (CFD) methodology is able to provide a volumetric description of a PEM fuel cell so it can be a useful tool to better understand the physical phenomena that govern the component operations. In this work, the open-source simulation library openFuelCell2 is adopted for a detailed analysis of two different PEM fuel cells characterized by standard distributor geometries, namely a parallel channel geometry and a serpentine configuration. The library, based on the OpenFOAM code, has been extended with a novel implementation accounting for the catalytic activity reduction due to the platinum oxide (PtOx) formation occurring under certain particular conditions. The adopted methodology is firstly validated resorting to experimental data acquired for the two different fuel cell configurations. The analysis highlights that the PtOx formation leads to a reduction in the fuel cell performance reaching up to 60–80% when operating at high voltages. Then, the effect of the distributor geometries on the component performance is investigated by resorting to in-plane and through-plane physical quantity distribution, such as reactant concentration, pressure or velocity fields. While the parallel flow channel configuration shows some diffusion losses under the rib, the serpentine channel geometry configuration can achieve some local performance peaks thanks to the convective flow in the gas diffusion layer (GDL) driven by local pressure gradients. Furthermore, the local enhancement in terms of higher current density under the rib is associated with an effective heat removal due to the high thermal capacity of the bipolar plate, avoiding the generation of local hot spots.
Open AccessComputational Fluid Dynamic Investigation of Local Flow-Field Conditions in Lab Polymer Electrolyte Membrane Fuel Cells to Identify Degradation Stressors and Performance Enhancers
The use of polymer electrolyte membrane (PEM) fuel cells as an alternative to internal combustion engines can significantly contribute to the decarbonization of the transport sector, especially for heavy-duty applications. However, degradation is still an issue for this type of component, affecting their durability and performance. In this scenario, a detailed analysis of the anodic and cathodic distributors’ flow-field geometry may help to identify some local stressors that trigger the degradation mechanism, such as local hot spots and reactants not having a uniform distribution. A computational fluid dynamic (CFD) methodology is able to provide a volumetric description of a PEM fuel cell so it can be a useful tool to better understand the physical phenomena that govern the component operations. In this work, the open-source simulation library openFuelCell2 is adopted for a detailed analysis of two different PEM fuel cells characterized by standard distributor geometries, namely a parallel channel geometry and a serpentine configuration. The library, based on the OpenFOAM code, has been extended with a novel implementation accounting for the catalytic activity reduction due to the platinum oxide (PtOx) formation occurring under certain particular conditions. The adopted methodology is firstly validated resorting to experimental data acquired for the two different fuel cell configurations. The analysis highlights that the PtOx formation leads to a reduction in the fuel cell performance reaching up to 60–80% when operating at high voltages. Then, the effect of the distributor geometries on the component performance is investigated by resorting to in-plane and through-plane physical quantity distribution, such as reactant concentration, pressure or velocity fields. While the parallel flow channel configuration shows some diffusion losses under the rib, the serpentine channel geometry configuration can achieve some local performance peaks thanks to the convective flow in the gas diffusion layer (GDL) driven by local pressure gradients. Furthermore, the local enhancement in terms of higher current density under the rib is associated with an effective heat removal due to the high thermal capacity of the bipolar plate, avoiding the generation of local hot spots.
- 9 April 2024
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
Application of a CFD Methodology for the Design of PEM Fuel Cell at the Channel Scale
Polymer electrolyte membrane (PEM) fuel cells will play a crucial role in the decarbonization of the transport sector, in particular for heavy duty applications. However, performance and durability of PEMFC stacks is still a concern especially when operated under high power density conditions, as required in order to improve the compactness and to reduce the cost of the system. In this context, the optimization of the geometry of hydrogen and air distributors represents a key factor to improve the distribution of the reactants on the active surface, in order to guarantee a proper water management and avoiding membrane dehydration. To this purpose, the adoption of CFD simulation tools can provide a useful insight into the physical phenomena which determine the efficient operation of the fuel cell (e.g. transport of mass, heat, species, electrons and ions, electrochemical reactions, water formation and removal), providing a valuable support for the design and the optimization of the device at the channel scale. In this work, an open-source simulation library, based on the OpenFOAM code, is applied to the detailed simulation of a basic module of a PEM fuel cell arranged with simple parallel channels. The simulation methodology is based on a multi-region and multi-physics approach, where the different components of the fuel cell (namely air and fuel channels, gas diffusion layers, catalyst layers, bipolar plates) are modeled resorting to different computational grids defining different local domains, on which the specific governing equations are solved. Transport phenomena in all of the local domains are coupled and solved simultaneously. The model is firstly validated resorting to experimental data acquired on a specific test bench installed at Politecnico di Milano. Then, a detailed analysis of the flow field is conducted in order to provide guidelines for the optimization of the distributor geometry. Finally, the influence of the channel design on the fuel cell performances is investigated, highlighting the influence of the rib-to-channel width geometrical parameter on the reactants diffusion and water removal.
- 9 April 2024
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
Application of a CFD Methodology for the Design of PEM Fuel Cell at the Channel Scale
Polymer electrolyte membrane (PEM) fuel cells will play a crucial role in the decarbonization of the transport sector, in particular for heavy duty applications. However, performance and durability of PEMFC stacks is still a concern especially when operated under high power density conditions, as required in order to improve the compactness and to reduce the cost of the system. In this context, the optimization of the geometry of hydrogen and air distributors represents a key factor to improve the distribution of the reactants on the active surface, in order to guarantee a proper water management and avoiding membrane dehydration. To this purpose, the adoption of CFD simulation tools can provide a useful insight into the physical phenomena which determine the efficient operation of the fuel cell (e.g. transport of mass, heat, species, electrons and ions, electrochemical reactions, water formation and removal), providing a valuable support for the design and the optimization of the device at the channel scale. In this work, an open-source simulation library, based on the OpenFOAM code, is applied to the detailed simulation of a basic module of a PEM fuel cell arranged with simple parallel channels. The simulation methodology is based on a multi-region and multi-physics approach, where the different components of the fuel cell (namely air and fuel channels, gas diffusion layers, catalyst layers, bipolar plates) are modeled resorting to different computational grids defining different local domains, on which the specific governing equations are solved. Transport phenomena in all of the local domains are coupled and solved simultaneously. The model is firstly validated resorting to experimental data acquired on a specific test bench installed at Politecnico di Milano. Then, a detailed analysis of the flow field is conducted in order to provide guidelines for the optimization of the distributor geometry. Finally, the influence of the channel design on the fuel cell performances is investigated, highlighting the influence of the rib-to-channel width geometrical parameter on the reactants diffusion and water removal.