Guangning Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guangning Wu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Dongli Xin
School of Electrical Engineering Southwest Jiaotong University Chengdu China
1 shared publication- Guizao Huang
Southwest Jiaotong University
1 shared publication Guoqiang Gao
College of Electrical Engineering, Southwest Jiaotong University 1 , Chengdu 610031, China
1 shared publicationHao Tang
China Electric Power Research Institute Beijing China
1 shared publication- Jie Li
State Key Laboratory of Electrical Insulation and Power Equipment Xi'an Jiaotong University Xi'an China
1 shared publication - Kai Liu
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
1 shared publication
Latest Publications
- Open Access
- 12 August 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (6)
In situ growth of silver nanoparticles on carbon fiber by plasma–liquid interaction to improve performance of epoxy composites
Grafting nanomaterials on the carbon fiber (CF) surface is considered an effective strategy for enhancing the interfacial properties of CF-reinforced polymer composites (CFRPs). However, the mechanical properties of the CFs are often compromised during treatment. A new method for in situ growing silver nanoparticles (AgNPs) on the CF surface is proposed in this study. The CFs are first immersed in a low-viscosity silver nitrate solution to form a thin liquid film on the surface. Subsequently, using the abundant active particles in the plasma, the silver ions are reduced to silver atoms and grown into AgNPs on the CF surface. The tensile strength of CF@Ag was 38.74% greater than that of untreated CF, potentially due to the reparative action of AgNPs on defects in CF. The CF showed an evident improvement in surface wettability because of the AgNPs. Furthermore, the interfacial properties were noticeably improved, with the interfacial shear strength of CF@Ag increasing to 91.59 MPa, which was about twice that of pristine CF. Thus, the mechanical properties of composites are significantly improved (flexural strength increased by 190.74%). This study presents a non-destructive and convenient method for growing nanoparticles onto CF to establish a robust interface in CFRPs.
- 12 August 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (6)
Open AccessIn situ growth of silver nanoparticles on carbon fiber by plasma–liquid interaction to improve performance of epoxy composites
Grafting nanomaterials on the carbon fiber (CF) surface is considered an effective strategy for enhancing the interfacial properties of CF-reinforced polymer composites (CFRPs). However, the mechanical properties of the CFs are often compromised during treatment. A new method for in situ growing silver nanoparticles (AgNPs) on the CF surface is proposed in this study. The CFs are first immersed in a low-viscosity silver nitrate solution to form a thin liquid film on the surface. Subsequently, using the abundant active particles in the plasma, the silver ions are reduced to silver atoms and grown into AgNPs on the CF surface. The tensile strength of CF@Ag was 38.74% greater than that of untreated CF, potentially due to the reparative action of AgNPs on defects in CF. The CF showed an evident improvement in surface wettability because of the AgNPs. Furthermore, the interfacial properties were noticeably improved, with the interfacial shear strength of CF@Ag increasing to 91.59 MPa, which was about twice that of pristine CF. Thus, the mechanical properties of composites are significantly improved (flexural strength increased by 190.74%). This study presents a non-destructive and convenient method for growing nanoparticles onto CF to establish a robust interface in CFRPs.
- Open Access
- 2 January 2023
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 17 (5) , 1123-1134
A zero‐sample state evaluation model for valve‐side bushing of UHV converter transformer oriented to digital twin under attribute analysis
The valve‐side bushing of the UHV converter transformer is the key equipment in the DC transmission project, and its running state directly affects the security and stability of the power system. This paper analyses the attributes of the physical entities, uses the digital twins to establish the state feature set and proposes a zero‐sample state evaluation algorithm for the valve‐side bushing. First, the geometric, materials and electrical characteristics are analyzed, and the detailed components of carrier current are obtained by empirical mode decomposition. Then, COMSOL is used to establish digital twins, verify the validity of twins with axial heat distribution of bushing, and establish a state feature set with the extreme temperature inside and outside bushing. Finally, the fuzzy clustering algorithm is used to classify the state feature set, and the similarity is used as the index to realize the zero‐sample state evaluation of the valve‐side bushing. Through the demonstration and analysis of examples, the evaluation model solves the problems of difficulty in extracting the internal features, fewer fault samples, and training difficulty, which is conducive to improving the operation and maintenance management level of power transmission equipment.
- 2 January 2023
- Published by Institution of Engineering and Technology (IET) in IET Generation, Transmission & Distribution
- Vol. 17 (5) , 1123-1134
Open AccessA zero‐sample state evaluation model for valve‐side bushing of UHV converter transformer oriented to digital twin under attribute analysis
The valve‐side bushing of the UHV converter transformer is the key equipment in the DC transmission project, and its running state directly affects the security and stability of the power system. This paper analyses the attributes of the physical entities, uses the digital twins to establish the state feature set and proposes a zero‐sample state evaluation algorithm for the valve‐side bushing. First, the geometric, materials and electrical characteristics are analyzed, and the detailed components of carrier current are obtained by empirical mode decomposition. Then, COMSOL is used to establish digital twins, verify the validity of twins with axial heat distribution of bushing, and establish a state feature set with the extreme temperature inside and outside bushing. Finally, the fuzzy clustering algorithm is used to classify the state feature set, and the similarity is used as the index to realize the zero‐sample state evaluation of the valve‐side bushing. Through the demonstration and analysis of examples, the evaluation model solves the problems of difficulty in extracting the internal features, fewer fault samples, and training difficulty, which is conducive to improving the operation and maintenance management level of power transmission equipment.