Kai-Yuan Chao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kai-Yuan Chao has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Hua Xiang
Hua Xiang and Gi-Joon Nam with Design Automation Department, IBM Research, Yorktown Heights, NY, USA
1 shared publication - Kuang-Yao Lee
Department of Computer Science, National Tsing Hua University, Hsinchu, Taiwan
1 shared publication - Liang Deng
Department of Electrical and Computer Engineering, University of Illinois, Urbana-Champaign
1 shared publication - Martin D. F. Wong
Dept. of Electrical and Computer Engineering, Univ. of Illinois, Urbana-Champaign, Urbana, IL, 61801
1 shared publication - Ting-Chi Wang
National Tsing Hua University, Hsinchu, Taiwan
1 shared publication
Latest Publications
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 13-18
Coupling-aware Dummy Metal Insertion for Lithography
As integrated circuits manufacturing technology is advancing into 65nm and 45nm nodes, extensive resolution enhancement techniques (RETs) are needed to correctly manufacture a chip design. The widely used RET called off-axis illumination (OAI) introduces forbidden pitches which lead to very complex design rules. It has been observed that imposing uniformity on layout designs can substantially improve printability under OAI. For metal layers, uniformity can be achieved simply by inserting dummy metal wire segments at all free spaces. Simulation results indeed show significant improvement in printability with such a dummy metal insertion approach. To minimize mask cost, it is advantageous to use dummy metal segments that are of the same size as regular metal wires due to their simple geometry. But these dummy wires are printable and hence increase coupling capacitances and potentially affect yield. The alternative is to use a set of parallel sub-resolution thin wires (which is not printed) to replace a printable dummy wire segment. These invisible dummy metal segments do not increase coupling capacitances but bring a higher lithography cost, which includes mask cost and RET/process expense. This paper presents a strategy for dummy metal insertion that can optimally trade off lithography cost and coupling capacitance. In particular, we present an optimal algorithm that can minimize lithography cost subject to any given coupling capacitance bound. Moreover, this dummy metal insertion achieves a highly uniform density because of the locality of coupling capacitance, which automatically ameliorates chemical mechanical polish (CMP) problem.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 13-18
Coupling-aware Dummy Metal Insertion for Lithography
As integrated circuits manufacturing technology is advancing into 65nm and 45nm nodes, extensive resolution enhancement techniques (RETs) are needed to correctly manufacture a chip design. The widely used RET called off-axis illumination (OAI) introduces forbidden pitches which lead to very complex design rules. It has been observed that imposing uniformity on layout designs can substantially improve printability under OAI. For metal layers, uniformity can be achieved simply by inserting dummy metal wire segments at all free spaces. Simulation results indeed show significant improvement in printability with such a dummy metal insertion approach. To minimize mask cost, it is advantageous to use dummy metal segments that are of the same size as regular metal wires due to their simple geometry. But these dummy wires are printable and hence increase coupling capacitances and potentially affect yield. The alternative is to use a set of parallel sub-resolution thin wires (which is not printed) to replace a printable dummy wire segment. These invisible dummy metal segments do not increase coupling capacitances but bring a higher lithography cost, which includes mask cost and RET/process expense. This paper presents a strategy for dummy metal insertion that can optimally trade off lithography cost and coupling capacitance. In particular, we present an optimal algorithm that can minimize lithography cost subject to any given coupling capacitance bound. Moreover, this dummy metal insertion achieves a highly uniform density because of the locality of coupling capacitance, which automatically ameliorates chemical mechanical polish (CMP) problem.
- 1 November 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10923152,p. 633-640
Post-Routing Redundant Via Insertion and Line End Extension with Via Density Consideration
Redundant via insertion and line end extension employed in the post-routing stage are two well known and highly recommended techniques to reduce yield loss due to via failure. However, if the amount of inserted redundant vias is not well controlled, it could violate via density rules and adversely worsen the yield and reliability of the design. In this paper, we first study the problem of redundant via insertion, and present two methods to accelerate a state-of-the-art approach (which is based on a maximum independent set (MIS) formulation) to solve it. We then consider the problem of simultaneous redundant via insertion and line end extension. We formulate the problem as a maximum weighted independent set (MWIS) problem and modify the accelerated MIS-based approach to solve it. Lastly, we investigate the problem of simultaneous redundant via insertion and line end extension subject to the maximum via density rule, and present a two-stage approach for it. In the first stage, we ignore the maximum via density rule, and enhance the MWIS-based approach to find the set of regions which violate the maximum via density rule after performing simultaneous redundant via insertion and line end extension. In the second stage, excess redundant vias are removed from those violating regions such that after the removal, the maximum via density rule is met while the total amount of redundant vias removed is minimized. This density-aware redundant via removal problem is formulated as a set of zero-one integer linear programming (0-1 ILP) problems each of which can be solved independently without sacrificing the optimality. The superiorities of our approaches are all demonstrated through promising experimental results
- 1 November 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10923152,p. 633-640
Post-Routing Redundant Via Insertion and Line End Extension with Via Density Consideration
Redundant via insertion and line end extension employed in the post-routing stage are two well known and highly recommended techniques to reduce yield loss due to via failure. However, if the amount of inserted redundant vias is not well controlled, it could violate via density rules and adversely worsen the yield and reliability of the design. In this paper, we first study the problem of redundant via insertion, and present two methods to accelerate a state-of-the-art approach (which is based on a maximum independent set (MIS) formulation) to solve it. We then consider the problem of simultaneous redundant via insertion and line end extension. We formulate the problem as a maximum weighted independent set (MWIS) problem and modify the accelerated MIS-based approach to solve it. Lastly, we investigate the problem of simultaneous redundant via insertion and line end extension subject to the maximum via density rule, and present a two-stage approach for it. In the first stage, we ignore the maximum via density rule, and enhance the MWIS-based approach to find the set of regions which violate the maximum via density rule after performing simultaneous redundant via insertion and line end extension. In the second stage, excess redundant vias are removed from those violating regions such that after the removal, the maximum via density rule is met while the total amount of redundant vias removed is minimized. This density-aware redundant via removal problem is formulated as a set of zero-one integer linear programming (0-1 ILP) problems each of which can be solved independently without sacrificing the optimality. The superiorities of our approaches are all demonstrated through promising experimental results