Alexey Belov
Alexey Belov has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- A. S. Suvorov
ТОО “CLTaCCM” – Central Laboratory of Tests and Certification Construction Materials
1 shared publication - Abdy Kiyalbaev
L.B. Goncharov Kazakh Automobile and Road Institute, Almaty 050061, Kazakhstan
1 shared publication - Akmaral Sagybekova
Kazakh Automobile and Road Institute named after L. B. Goncharov (KazADI), Kazakhstan
1 shared publication - Alexandra Alexandrovna Kalinina
Enikolopov Institute of Synthetic Polymeric Materials, Russian Academy of Sciences, 117393 Moscow, Russia
1 shared publication - Amiri Hajera Azizullah
ALT Mukhamedjan Tynyshpaev University
1 shared publication - Dauren Yessentay
L.B. Goncharov Kazakh Automobile and Road Institute, Almaty 050061, Kazakhstan
1 shared publication
Latest Publications
- 15 June 2026
- Published by L.B. Goncharov Kazakh Automobile and Road Institute in Bulletin of Kazakh Automobile and Road Institute
- Vol. 14 (2) , 38-53
Laser scanning-based diagnostics of highway bridge crossings
Highway bridge structures require regular condition assessment to ensure traffic safety and support timely maintenance planning. This study aimed to evaluate the effectiveness of laser scanning technology for the inspection of a highway bridge crossing and its approaches. The methodology combined a DJI Matrice 350 RTK unmanned aerial vehicle, a handheld laser scanner, LiDAR technology, RTK positioning, and photogrammetric processing of spatial data. As a result, an orthophoto map, a dense point cloud, and a three-dimensional digital model of the bridge were generated. Automated detection and classification of pavement defects, including transverse, longitudinal, thermal, and local cracks, were performed with the determination of their geometric characteristics and spatial coordinates. The generated digital datasets enabled the creation of a georeferenced defect database suitable for long-term structural condition monitoring. The findings demonstrate that integrating aerial and terrestrial laser scanning significantly improves the accuracy and objectivity of bridge inspections, reduces survey time, and provides a reliable digital foundation for bridge asset management and lifecycle monitoring.
- 15 June 2026
- Published by L.B. Goncharov Kazakh Automobile and Road Institute in Bulletin of Kazakh Automobile and Road Institute
- Vol. 14 (2) , 38-53
Laser scanning-based diagnostics of highway bridge crossings
Highway bridge structures require regular condition assessment to ensure traffic safety and support timely maintenance planning. This study aimed to evaluate the effectiveness of laser scanning technology for the inspection of a highway bridge crossing and its approaches. The methodology combined a DJI Matrice 350 RTK unmanned aerial vehicle, a handheld laser scanner, LiDAR technology, RTK positioning, and photogrammetric processing of spatial data. As a result, an orthophoto map, a dense point cloud, and a three-dimensional digital model of the bridge were generated. Automated detection and classification of pavement defects, including transverse, longitudinal, thermal, and local cracks, were performed with the determination of their geometric characteristics and spatial coordinates. The generated digital datasets enabled the creation of a georeferenced defect database suitable for long-term structural condition monitoring. The findings demonstrate that integrating aerial and terrestrial laser scanning significantly improves the accuracy and objectivity of bridge inspections, reduces survey time, and provides a reliable digital foundation for bridge asset management and lifecycle monitoring.
- 20 March 2026
- Published by L.B. Goncharov Kazakh Automobile and Road Institute in Bulletin of Kazakh Automobile and Road Institute
- Vol. 13 (1) , 3-17
Dynamic analysis of the stress–strain state of a railway bridge beam superstructure under moving train loads
The article presents a numerical dynamic analysis of the stress-strain state of a railway bridge under load from a moving train. The aim is to evaluate the reaction of reinforced concrete superstructures to dynamic loads from rolling stock with increased axial loads, which is a development of previous static studies. A spatial finite element model has been created in the MIDAS Civil environment that takes into account geometry, material properties, boundary conditions, and the interaction of elements. Loads from a moving train were modeled using dynamic scenarios based on locomotive-wagon configurations, speed, and axial distances. The analysis of the dynamic response revealed the influence of dynamic effects on the stress-strain state, with an increase in stress levels compared to static scenarios. The study highlights the importance of dynamic analysis for the safe operation of railway bridges under conditions of increased loads and speeds, and can be used to evaluate, monitor, design, and improve computational approaches.
- 20 March 2026
- Published by L.B. Goncharov Kazakh Automobile and Road Institute in Bulletin of Kazakh Automobile and Road Institute
- Vol. 13 (1) , 3-17
Dynamic analysis of the stress–strain state of a railway bridge beam superstructure under moving train loads
The article presents a numerical dynamic analysis of the stress-strain state of a railway bridge under load from a moving train. The aim is to evaluate the reaction of reinforced concrete superstructures to dynamic loads from rolling stock with increased axial loads, which is a development of previous static studies. A spatial finite element model has been created in the MIDAS Civil environment that takes into account geometry, material properties, boundary conditions, and the interaction of elements. Loads from a moving train were modeled using dynamic scenarios based on locomotive-wagon configurations, speed, and axial distances. The analysis of the dynamic response revealed the influence of dynamic effects on the stress-strain state, with an increase in stress levels compared to static scenarios. The study highlights the importance of dynamic analysis for the safe operation of railway bridges under conditions of increased loads and speeds, and can be used to evaluate, monitor, design, and improve computational approaches.
- Open Access
- 1 January 2026
- Published by Wiley in International Journal of Chemical Engineering
- Vol. 2026 (1)
Functional Effectiveness of Hydrophobic Additives Based on PEGylated Hyperbranched Polymethylethoxysiloxane and Silicasol in Cement Systems
Concrete, as a building material, is strong and durable. However, under the influence of aggressive environmental factors, it can undergo corrosion and destruction. Water, in the form of precipitation and groundwater, is one such medium that can have a negative impact on concrete. Water is a weak solution of salts, acids, and bases, and it can lead to the deterioration of concrete structures. To prevent the negative effects of water on concrete, various additives are used. These additives help to increase the resistance of concrete to moisture. Among these additives, organosilicon‐based compounds are particularly effective. They have unique physicochemical properties and are economical to produce. However, the exact mechanism of their action is not fully understood. The aim of this research is to investigate the effect of a specific type of hydrophobic additive on the physical and mechanical properties of concrete. This additive is based on polymethylethoxysiloxane–polyethylene glycol (PMEOS–PEG) and silica sol in ethyl cellulose (silicasol). The results of the study will help to better understand the role of these additives in improving the durability of concrete structures under water‐related conditions. PMEOS–PEG has been shown to increase the mobility of the solvent mixture and also slightly increase the latency. Silicasol, on the other hand, does not affect mobility and has a significant retarding effect. The introduction of PMEOS–PEG hydrophobizer increases the strength of mixtures by 50%, when using Portland cement grade CEM II/A‐S 42.5 N, and by 20% in mixtures with unmodified Portland cement CEM I 42.5 N. Silicasol’s addition does not alter the strength characteristics of cement–sand mixtures. There is a slight tendency toward a decrease when using CEM I 42.5 N. The water impermeability of concrete samples using PMEOS–PEG and silicasol at a dosage of 0.7% increases from W6 (without additives) to W12 and W8, respectively.
- 1 January 2026
- Published by Wiley in International Journal of Chemical Engineering
- Vol. 2026 (1)
Open AccessFunctional Effectiveness of Hydrophobic Additives Based on PEGylated Hyperbranched Polymethylethoxysiloxane and Silicasol in Cement Systems
Concrete, as a building material, is strong and durable. However, under the influence of aggressive environmental factors, it can undergo corrosion and destruction. Water, in the form of precipitation and groundwater, is one such medium that can have a negative impact on concrete. Water is a weak solution of salts, acids, and bases, and it can lead to the deterioration of concrete structures. To prevent the negative effects of water on concrete, various additives are used. These additives help to increase the resistance of concrete to moisture. Among these additives, organosilicon‐based compounds are particularly effective. They have unique physicochemical properties and are economical to produce. However, the exact mechanism of their action is not fully understood. The aim of this research is to investigate the effect of a specific type of hydrophobic additive on the physical and mechanical properties of concrete. This additive is based on polymethylethoxysiloxane–polyethylene glycol (PMEOS–PEG) and silica sol in ethyl cellulose (silicasol). The results of the study will help to better understand the role of these additives in improving the durability of concrete structures under water‐related conditions. PMEOS–PEG has been shown to increase the mobility of the solvent mixture and also slightly increase the latency. Silicasol, on the other hand, does not affect mobility and has a significant retarding effect. The introduction of PMEOS–PEG hydrophobizer increases the strength of mixtures by 50%, when using Portland cement grade CEM II/A‐S 42.5 N, and by 20% in mixtures with unmodified Portland cement CEM I 42.5 N. Silicasol’s addition does not alter the strength characteristics of cement–sand mixtures. There is a slight tendency toward a decrease when using CEM I 42.5 N. The water impermeability of concrete samples using PMEOS–PEG and silicasol at a dosage of 0.7% increases from W6 (without additives) to W12 and W8, respectively.
- Open Access
- 29 November 2022
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 6,p. 3-11
Comparison of test results to determine the parameters of soil strength to ensure the stability of earth slopes
The content of large soil fractions in soils complicates the experimental part of the research, but, the modeling method makes it possible to determine the effect of soil filler on slope stability. The article presents the results of experimental study of the strength of coarse-clastic soils with different percentages of large fractions of gravelly soil (up to 20 mm) and aggregate (up to 5 mm) in the study of slope stability. The studies were carried out on three types of experimental equipment, which confirms the reliability of the results obtained. Recommendations are given for applying the values of the strength characteristics of coarse-grained soils in calculating the stability of slopes. The results of the tests are carried out in a tray and shear testing devices. Mixture of soil fractions from 2 mm to 50 mm. Purpose of the tests is to determine the actual parameters of soil strength j and C, taking into account the effect of impurities on the stability of slopes. Reliability of the results confirmed the comparability of the results of previous tests. Tray allows for testing models of slopes composed of mixtures of sand fractions from 2 mm to 20 mm. Model sizes slopes are defined relative to the size tray. Tray dimensions ‑ length 1400 mm, width 500 mm, height 1000 mm. The design of the shear device allows to investigate coarse soils of different factions. The diameter of the fractions were tested for shear device area of 100 sm2 is from 2 mm to 20 mm. The diameter of the fractions were tested for shear device area of 1000 sm2 ‑ from 5 mm to 50 mm. The experiments were performed in the laboratory "Geotechnics in Construction" in KazGASA.
- 29 November 2022
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 6,p. 3-11
Open AccessComparison of test results to determine the parameters of soil strength to ensure the stability of earth slopes
The content of large soil fractions in soils complicates the experimental part of the research, but, the modeling method makes it possible to determine the effect of soil filler on slope stability. The article presents the results of experimental study of the strength of coarse-clastic soils with different percentages of large fractions of gravelly soil (up to 20 mm) and aggregate (up to 5 mm) in the study of slope stability. The studies were carried out on three types of experimental equipment, which confirms the reliability of the results obtained. Recommendations are given for applying the values of the strength characteristics of coarse-grained soils in calculating the stability of slopes. The results of the tests are carried out in a tray and shear testing devices. Mixture of soil fractions from 2 mm to 50 mm. Purpose of the tests is to determine the actual parameters of soil strength j and C, taking into account the effect of impurities on the stability of slopes. Reliability of the results confirmed the comparability of the results of previous tests. Tray allows for testing models of slopes composed of mixtures of sand fractions from 2 mm to 20 mm. Model sizes slopes are defined relative to the size tray. Tray dimensions ‑ length 1400 mm, width 500 mm, height 1000 mm. The design of the shear device allows to investigate coarse soils of different factions. The diameter of the fractions were tested for shear device area of 100 sm2 is from 2 mm to 20 mm. The diameter of the fractions were tested for shear device area of 1000 sm2 ‑ from 5 mm to 50 mm. The experiments were performed in the laboratory "Geotechnics in Construction" in KazGASA.