Ajith Ambalakatte
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ajith Ambalakatte has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Alasdair Cairns
Brunel University London
5 shared publications Anthony Harrington
2 shared publicationsJonathan Hall
2 shared publicationsMike Bassett
2 shared publications- Sikai Geng2 shared publications
A. Harrington
MAHLE Powertrain Ltd, Northampton, UK
1 shared publication
Latest Publications
- Open Access
- 28 June 2026
- Published by Cardiff University Press in Journal of Ammonia Energy
- Vol. 4 (1) , 39-54
Experimental And Computational Investigation of Using an Exhaust Recuperated Ammonia Cracker in a Spark Ignited Engine
Green ammonia by virtue of being a good hydrogen carrier is garnering significant interest as a zero-carbon alternative to traditional fossil fuels especially in hard-to-abate sectors, despite its unfavourable combustion characteristics and toxicity attributes. However, spark ignited engine can operate on pure ammonia only at low speed and high load conditions requiring co-fuelling with hydrogen to widen the stable operation window to higher speeds and lower loads. Another challenge with operating under these conditions with minimum hydrogen in the fuel mix is the significant engine out emissions of unburned ammonia (~6000-9000ppm). Prior research conducted by the current reported researchers found a lean operating strategy which results in equal amounts of NOx and unburned ammonia which converts into nitrogen and water vapour when fed into a Selective Catalytic Reduction (SCR) system. This strategy was further validated using cracked gas for H2 instead of bottled gas using an onboard cracker mimicking real world scenario. The reported work investigates computational end experimental integration of an electrically heated thermo-chemical cracker to a single cylinder SI engine, where the ammonia is fed into the cracker is pre-heated using an exhaust recuperator. The results from the experiments show that the ammonia can be heated to >5000C even with an unoptimized exhaust recuperator, this accounted for ~30% of the total energy consumed to crack ammonia with significant heat loss as the ammonia transferred between the exhaust recuperator and cracker. A computational model was developed to optimise the losses and the results from model show an 8% reduction in the total energy consumption. This work shows the viability of operating an internal combustion engine with a single fuel ammonia system having minimal penalty to overall efficiency while maintaining optimum engine out emissions.
- 28 June 2026
- Published by Cardiff University Press in Journal of Ammonia Energy
- Vol. 4 (1) , 39-54
Open AccessExperimental And Computational Investigation of Using an Exhaust Recuperated Ammonia Cracker in a Spark Ignited Engine
Green ammonia by virtue of being a good hydrogen carrier is garnering significant interest as a zero-carbon alternative to traditional fossil fuels especially in hard-to-abate sectors, despite its unfavourable combustion characteristics and toxicity attributes. However, spark ignited engine can operate on pure ammonia only at low speed and high load conditions requiring co-fuelling with hydrogen to widen the stable operation window to higher speeds and lower loads. Another challenge with operating under these conditions with minimum hydrogen in the fuel mix is the significant engine out emissions of unburned ammonia (~6000-9000ppm). Prior research conducted by the current reported researchers found a lean operating strategy which results in equal amounts of NOx and unburned ammonia which converts into nitrogen and water vapour when fed into a Selective Catalytic Reduction (SCR) system. This strategy was further validated using cracked gas for H2 instead of bottled gas using an onboard cracker mimicking real world scenario. The reported work investigates computational end experimental integration of an electrically heated thermo-chemical cracker to a single cylinder SI engine, where the ammonia is fed into the cracker is pre-heated using an exhaust recuperator. The results from the experiments show that the ammonia can be heated to >5000C even with an unoptimized exhaust recuperator, this accounted for ~30% of the total energy consumed to crack ammonia with significant heat loss as the ammonia transferred between the exhaust recuperator and cracker. A computational model was developed to optimise the losses and the results from model show an 8% reduction in the total energy consumption. This work shows the viability of operating an internal combustion engine with a single fuel ammonia system having minimal penalty to overall efficiency while maintaining optimum engine out emissions.
- Open Access
- 21 October 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 187
Predicting NOx emissions from ammonia engines – Fuel and thermal effects
- 21 October 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 187
Open AccessPredicting NOx emissions from ammonia engines – Fuel and thermal effects
- Open Access
- 12 April 2025
- Published by Cardiff University Press in Journal of Ammonia Energy
- Vol. 3 (1)
Towards an Optimised Lean Burn Operating Strategy for an Ammonia-Hydrogen Co-fuelled Spark Ignition Engine
Ammonia is now widely considered as a promising renewable fuel, primarily due to favourable storage and transportation characteristics and end use in applications where robust health and safety protocols can always be upheld. In the currently reported work, a thermodynamic single-cylinder spark ignition research engine was fitted with separated gaseous ammonia and hydrogen port fuel injection, with experiments undertaken to improve understanding of the impact of varied co-fuelling upon combustion, performance, fuel economy and emissions. Under stoichiometric conditions with pure ammonia (NH3), it was possible to operate under stable combustion at low-to-medium speeds and medium-to-high engine loads. At the lowest loads, up to ~20% hydrogen (by energy) was required. Engine-out NH3 emissions remained relatively high across the stoichiometric operating map (~7,000-8,000ppm). An alternative hydrogen co-fuelling lean burn spark-ignition strategy was then developed with the aim of improving engine efficiency and balancing engine-out emissions to be compatible with future use of Selective Catalytic Reduction (SCR) after-treatment technology. This was based upon directly using NH3 slip as a NOx reductant within an SCR unit and ideally eliminating conventional urea-based fluid injection. Ideally, such SCR systems operate with a fixed “alpha ratio” equal to ~1 (where alpha ratio is the ratio of engine-out NH3 to NOx on a ppm basis, with a value of unity indicating the ideal amount of reductant to simultaneously consume NH3 slip and decompose NOx). Several speed and load sweeps were undertaken to evaluate the ideal combinations of hydrogen substitution ratio and relative air-to-fuel ratio (l). It was concluded that operating the engine with ~20% hydrogen and slightly lean (l~1.2) would result in an ideal alpha ratio of ~1 across the majority of the map, with little variation in alpha ratio or lambda noted with changing engine speed and load. The results indicate, apparently for the first time, the high promise of such a co-fuelling engine operating strategy to enable high engine efficiency with minimised pollutant emissions via existing SCR emissions after-treatment technology. The supplementary hydrogen was noted to also result in small improvements in indicated thermal efficiency of 1-2% compared to baseline stoichiometric operation with 100% ammonia, with accompanying basic calculations indicating this may help offset any penalties from on-board hydrogen production via thermo-catalytic NH3 cracking. Overall, the work has demonstrated a new engine operating strategy to help overcome the challenges of slow NH3 combustion and high pollutant emissions via existing diesel engine after-treatment technologies.
- 12 April 2025
- Published by Cardiff University Press in Journal of Ammonia Energy
- Vol. 3 (1)
Open AccessTowards an Optimised Lean Burn Operating Strategy for an Ammonia-Hydrogen Co-fuelled Spark Ignition Engine
Ammonia is now widely considered as a promising renewable fuel, primarily due to favourable storage and transportation characteristics and end use in applications where robust health and safety protocols can always be upheld. In the currently reported work, a thermodynamic single-cylinder spark ignition research engine was fitted with separated gaseous ammonia and hydrogen port fuel injection, with experiments undertaken to improve understanding of the impact of varied co-fuelling upon combustion, performance, fuel economy and emissions. Under stoichiometric conditions with pure ammonia (NH3), it was possible to operate under stable combustion at low-to-medium speeds and medium-to-high engine loads. At the lowest loads, up to ~20% hydrogen (by energy) was required. Engine-out NH3 emissions remained relatively high across the stoichiometric operating map (~7,000-8,000ppm). An alternative hydrogen co-fuelling lean burn spark-ignition strategy was then developed with the aim of improving engine efficiency and balancing engine-out emissions to be compatible with future use of Selective Catalytic Reduction (SCR) after-treatment technology. This was based upon directly using NH3 slip as a NOx reductant within an SCR unit and ideally eliminating conventional urea-based fluid injection. Ideally, such SCR systems operate with a fixed “alpha ratio” equal to ~1 (where alpha ratio is the ratio of engine-out NH3 to NOx on a ppm basis, with a value of unity indicating the ideal amount of reductant to simultaneously consume NH3 slip and decompose NOx). Several speed and load sweeps were undertaken to evaluate the ideal combinations of hydrogen substitution ratio and relative air-to-fuel ratio (l). It was concluded that operating the engine with ~20% hydrogen and slightly lean (l~1.2) would result in an ideal alpha ratio of ~1 across the majority of the map, with little variation in alpha ratio or lambda noted with changing engine speed and load. The results indicate, apparently for the first time, the high promise of such a co-fuelling engine operating strategy to enable high engine efficiency with minimised pollutant emissions via existing SCR emissions after-treatment technology. The supplementary hydrogen was noted to also result in small improvements in indicated thermal efficiency of 1-2% compared to baseline stoichiometric operation with 100% ammonia, with accompanying basic calculations indicating this may help offset any penalties from on-board hydrogen production via thermo-catalytic NH3 cracking. Overall, the work has demonstrated a new engine operating strategy to help overcome the challenges of slow NH3 combustion and high pollutant emissions via existing diesel engine after-treatment technologies.
- Open Access
- 20 December 2023
- Published by Springer Nature in Carbon Neutrality
- Vol. 2 (1) , 1-17
Evaluation of ammonia-gasoline co-combustion in a modern spark ignition research engine
Ammonia (NH3) is emerging as a potential favoured fuel for longer range decarbonised heavy transport, particularly in the marine sector, predominantly due to highly favourable characteristics as an effective hydrogen carrier. This is despite generally unfavourable combustion and toxicity attributes, restricting end use to applications where robust health and safety protocols can always be upheld. In the currently reported work, a spark ignited thermodynamic single cylinder research engine equipped with gasoline direct injection was upgraded to include gaseous ammonia port injection fuelling, with the aim of understanding maximum viable ammonia substitution ratios across the speed-load operating map. The work was conducted at varied effective compression ratios under overall stoichiometric conditions, with the spark timing re-optimised for maximum brake torque at all stable logged sites. The experiments included industry standard measurements of combustion, performance, and engine-out emissions (including NH3 “slip”). With a geometric compression ratio of 11.2:1, it was found possible to run the engine on pure ammonia at low engine speeds (1000-1800 rpm) and loads of 12 bar net IMEP. When progressively dropping down below this load limit an increasing amount of gasoline co-firing was required to avoid engine misfire. When operating at 1800 rpm and 12 bar net IMEP, all emissions of carbon (CO2, CO, unburned hydrocarbons) and NOx decreased considerably when switching to higher NH3 substitution ratios, with NOx reduced by ~ 45% at 1800 rpm/12 bar when switching from pure gasoline to pure NH3 (associated with longer and cooler combustion). By further increasing the geometric compression ratio to 12.4 and reducing the intake camshaft duration for maximum effective compression ratio, it was possible to operate the engine on pure ammonia at much lower loads in a fully warmed up state (e.g., linear low load limit line from 1000 rpm/6 bar net IMEP to 1800 rpm/9 bar net IMEP). Under all conditions, the indicated thermal efficiency of the engine was either equivalent to or slightly higher than that obtained using gasoline-only due to the favourable anti-knock rating of NH3. Ongoing work is concerned with detailed breakdown of individual NOx species together with measuring the impact of hydrogen enrichment across the operating map.
- 20 December 2023
- Published by Springer Nature in Carbon Neutrality
- Vol. 2 (1) , 1-17
Open AccessEvaluation of ammonia-gasoline co-combustion in a modern spark ignition research engine
Ammonia (NH3) is emerging as a potential favoured fuel for longer range decarbonised heavy transport, particularly in the marine sector, predominantly due to highly favourable characteristics as an effective hydrogen carrier. This is despite generally unfavourable combustion and toxicity attributes, restricting end use to applications where robust health and safety protocols can always be upheld. In the currently reported work, a spark ignited thermodynamic single cylinder research engine equipped with gasoline direct injection was upgraded to include gaseous ammonia port injection fuelling, with the aim of understanding maximum viable ammonia substitution ratios across the speed-load operating map. The work was conducted at varied effective compression ratios under overall stoichiometric conditions, with the spark timing re-optimised for maximum brake torque at all stable logged sites. The experiments included industry standard measurements of combustion, performance, and engine-out emissions (including NH3 “slip”). With a geometric compression ratio of 11.2:1, it was found possible to run the engine on pure ammonia at low engine speeds (1000-1800 rpm) and loads of 12 bar net IMEP. When progressively dropping down below this load limit an increasing amount of gasoline co-firing was required to avoid engine misfire. When operating at 1800 rpm and 12 bar net IMEP, all emissions of carbon (CO2, CO, unburned hydrocarbons) and NOx decreased considerably when switching to higher NH3 substitution ratios, with NOx reduced by ~ 45% at 1800 rpm/12 bar when switching from pure gasoline to pure NH3 (associated with longer and cooler combustion). By further increasing the geometric compression ratio to 12.4 and reducing the intake camshaft duration for maximum effective compression ratio, it was possible to operate the engine on pure ammonia at much lower loads in a fully warmed up state (e.g., linear low load limit line from 1000 rpm/6 bar net IMEP to 1800 rpm/9 bar net IMEP). Under all conditions, the indicated thermal efficiency of the engine was either equivalent to or slightly higher than that obtained using gasoline-only due to the favourable anti-knock rating of NH3. Ongoing work is concerned with detailed breakdown of individual NOx species together with measuring the impact of hydrogen enrichment across the operating map.
- Open Access
- 1 January 2023
- Published by IOP Publishing in Progress in Energy
- Vol. 5 (1) , 012004
Hydrogen storage in liquid hydrogen carriers: recent activities and new trends
Efficient storage of hydrogen is one of the biggest challenges towards a potential hydrogen economy. Hydrogen storage in liquid carriers is an attractive alternative to compression or liquefaction at low temperatures. Liquid carriers can be stored cost-effectively and transportation and distribution can be integrated into existing infrastructures. The development of efficient liquid carriers is part of the work of the International Energy Agency Task 40: Hydrogen-Based Energy Storage. Here, we report the state-of-the-art for ammonia and closed CO2-cycle methanol-based storage options as well for liquid organic hydrogen carriers.
- 1 January 2023
- Published by IOP Publishing in Progress in Energy
- Vol. 5 (1) , 012004
Open AccessHydrogen storage in liquid hydrogen carriers: recent activities and new trends
Efficient storage of hydrogen is one of the biggest challenges towards a potential hydrogen economy. Hydrogen storage in liquid carriers is an attractive alternative to compression or liquefaction at low temperatures. Liquid carriers can be stored cost-effectively and transportation and distribution can be integrated into existing infrastructures. The development of efficient liquid carriers is part of the work of the International Energy Agency Task 40: Hydrogen-Based Energy Storage. Here, we report the state-of-the-art for ammonia and closed CO2-cycle methanol-based storage options as well for liquid organic hydrogen carriers.