RHRamzy S. Hamied

Ramzy S. Hamied

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ramzy S. Hamied has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Improving Iraqi Heavy Crude Oil Properties (Viscosity, Gravity of API, Carbon Residue, Sulfur %) Through Dilution and Heating Methods

    by Ramzy S. Hamied, Anwar N. Mohammed Ali, Khalid A. Sukkar, Zaidoon M. Shakor, Ali Al-Shathr, Ahmed S. Rahim, Ali S. Ali, Ali H. Abd, Ali K. Salman

    Heavy crude oil, due to its higher viscosity, poses challenges for transportation via pipelines and production from reservoirs. This study aimed to evaluate the effectiveness of dilution and heating methods in assessing the influence of organic solvents on the heavy crude oil properties. Specifically, it focused on viscosity, API gravity, Conradson carbon residue, and sulfur content, as well as viscosity reduction. Heavy crude oil samples were collected from the oil field of Al-Ahdab. The heavy crude oil was treated with various fractions of n-heptane and toluene, along with a mixture of 50% n-heptane and 50% toluene, added at concentrations of 5, 10, and 15 wt % at a temperature of 25°C. The study also examined the impact of temperature, varying from 25 to 50°C, on viscosity. Results indicated that diluting heavy oil samples with toluene produced the most favorable results at the 15% addition compared to the other solvents used. Heavy crude oil viscosity decreased to 26.221 cst, with a density of 847.9 kg/m3 and an API gravity of 31.755. Additionally, the total sulfur content was reduced to 3.2%, and the Conradson carbon residue decreased to 7.9‒6.3%. The study further analyzed the influence of temperatures from 25 to 50°C, considering solar heating as a low-cost renewable energy source, on viscosity and viscosity reduction percentage (VR %). It was found that as temperature increased, the viscosity of heavy crude oil decreased. This reduction was more pronounced with higher solvent concentrations: 15 > 10 > 5%, leading to reductions of 74.5, 60.4, and 52.3%, respectively. As a result, the heavy crude oil became lighter and more efficient than the original crude oil, with toluene showing superior performance compared to the other solvents in terms of overall characteristics.

  • Study the Influence of Sulfur Content and Pressure Gradient for Iraqi Crude Oil Discharge through Pipelines

    by Anwar N. Mohammed Ali, Ramzy S. Hamied, Khalid A. Sukkar, Zaidoon M. Shakor

    Crude oils are a complex mixture of hundreds of different volatile hydrocarbon molecules and organic materials in the liquid phase accompanied by elemental compounds and contaminants. In the present work, sulfur content influence variations on velocity flow (Reynolds number) of different Iraqi crude oil fields (Refinery of Diwaniya, East Baghdad, and Thi-Qar), and pressure gradient (dp) on the pump power, power loses and the crude oil flow rate have been evaluated. Further, energy losses and the total discharge are appraised to state the feasibility of using desulfurization unit’s in the oil fields. All the experiments have used different API crude oil, with the studied at the oil field surface pipelines sections connecting operating at different sulfur content % and taking the pressure gradient of (2, 4, and 6 kg/cm2), at constant temperature of 28.9°C, and with a constant 4 in pipe diameter. When the sulfur content increases results show that the three types of crude oils (Refinery of Diwaniya, east Baghdad, and Thi-Qar oil fields) the total pumping energy rises when the flow rate becomes smaller through the pipeline, while small influence for energy losses. The increasing pressure gradient (this means that differential pressure was increased), there was more flow rate and with the same behavior vis sulfur content. There is a direct proportion between the flow rate and the pressure differential. Greater flow rates produced from higher pressure differences, as the high-pressure gradient in the line consumes energy must also be large. Also expected that when increasing the sulfur content in the field especially for high percentage (2.1%) in the crude oil will decrease the flow rate and increase the pump power, power losses therefore adding unit to treatment the sulfur very important economically to avoid this entire problem.


  • Open Access

    Catalytic-Level Identification of Prepared Pt/HY, Pt-Zn/HY, and Pt-Rh/HY Nanocatalysts on the Reforming Reactions of N-Heptane

    by Ramzy S. Hamied, Khalid A. Sukkar, Hasan Shakir Majdi, Zainb Y. Shnain, Mohammed Shorbaz Graish, Luma H. Mahmood

    The operation of reforming catalysts in a fixed bed reactor undergoes a high level of interaction between the operating parameters and the reaction mechanism. Understanding such an interaction reduces the catalyst deactivation rate. In the present work, three kinds of nanocatalysts (i.e., Pt/HY, Pt-Zn/HY, and Pt-Rh/HY) were synthesized. The catalysts’ performances were evaluated for n-heptane reactions in the fixed bed reactor. The operating conditions applied were the following: 1 bar pressure, WHSV of 4, hydrogen/n-heptane ratio of 4, and the reaction temperatures of 425, 450, 475, 500, and 525 °C. The optimal reaction temperature for all three types of nanocatalysts to produce high-quality isomers and aromatic hydrocarbons was 500 °C. Accordingly, the nanocatalyst Pt-Zn/HY provided the highest catalytic selectivity for the desired hydrocarbons. Moreover, the Pt-Zn/HY-nanocatalyst showed more resistance against catalyst deactivation in comparison with the other two types of nanocatalysts (Pt/HY and Pt-Rh/HY). This work offers more understanding for the application of nanocatalysts in the reforming process in petroleum refineries with high performance and economic feasibility.


  • Open Access

    Enhancing Heavy Crude Oil Flow in Pipelines through Heating-Induced Viscosity Reduction in the Petroleum Industry

    by Ramzy S. Hamied, Anwar N. Mohammed Ali, Khalid A. Sukkar

    The process of transporting crude oil across pipelines is one of the most critical aspects of the midstream petroleum industry. In the present experimental work, the effect of temperature, pressure drop, and pipe diameter on the flow rate of heavy crude oil have been assessed. Moreover, the total discharge and energy losses have been evaluated in order to demonstrate the improvements potentially achievable by using solar heating method replacing pipe, and adjusting the value of the initial pressure difference. Crude oil of API = 20 has been used for the experiments, with the studied pipelines sections connecting the separator unit to the storage tank operating at a temperature of 25°C–100°C, pressure drop of 3, 4, 5, and 6 kg/cm2, and with pipe diameter of 4, 6, and 8 in. The results show that on increasing the temperature and/or the pressure drop, the flow rate through the pipeline becomes higher, thus raising the total pumping energy (as the pipe diameter increase), while energy losses increase from the last separator to the storage tank in the field. A pipe diameter increase can also produce a growth of the total pumping energy (i.e., energy losses increase). The results of the present analysis suggest that employing an optimal temperature (50°C) is needed to ensure good performance.


  • Open Access

    Study the Effect of Corrosion on the Pipes of Oil Well Production

    by Ramzy. S. Hamied Hamied, Mohammad. A. Alhassan Alhassan, Mayssaa. A. Al-Bidry Al-Bidry

    Corrosion costs of the oil industry are billions of dollars in a year. Corrosion affects every aspect ofexploration and production of oil, from offshore rigs to casing and transporting the crude oil torefinery or exporting terminal. This study aims to investigate the effect of sulfur content on thecorrosion of carbon steel and composite material (polyester/fiberglass) pipes used in wellproduction. .In the present work three specimens of pipes from (Al – Nasiriyah oil field, Al – Daura refinery, andcomposite material) are prepared in the center of the training and workshop in university oftechnology with (3, and 5 mm) thickness and (30 mm) diameter which immersed in different typesof Iraqi crude oil field (East – Baghdad, Al – Nasiriyah, and Al – Rumaila field) in different times (0,14, 28, 42, and 56 day). Physical properties (viscosity, density, API grade, specific gravity (sp.gr),sulfur %, sediment %, and water %) of three types of Iraqi crude oil are tested in lab of petroleumtechnology department. Also study specimens of pipes by microscope to knowing the effect ofsulfur % on these specimens. .The results showed that when increasing duration of immersed pipes and sulfur content in crude oilincreased the rate of corrosion, and the composite material pipe gives the best result compared withthe other two specimens pipes used because they didn’t influenced by corrosion when immersed inIraqi crude oil. Also, it was noted that the diffusion coefficient decreased in composite pipecompared with the other pipes.


  • Open Access

    Diagnosing Water Problem for Asmari Reservoir in Abu Ghirab Oilfield Using Analytical and Numerical Approaches

    by Mustafa Adil Mohammed, Sameera Hamd- Allah, Ramzy Hameed

    Asmari is the main productive reservoir in Abu Ghirab oilfield in the south-east part of Iraq. It has history production extends from 1976 up to now with several close periods. Recently, the reservoir suffers some problems in production, which are abstracted as water production rising with oil production declining in most wells. The water problem type of the field and wells is identified by using Chan's diagnostic plots (water oil ratio (WOR) and derivative water oil ratio (WOR') against time). The analytical results show that water problem is caused by the channeling due to high permeability zones, high water saturation zones, and faults or fracturing. The numerical approach is also used to study the water movement inside the reservoir. A three dimensional geological and a three phase reservoir model was constructed for Asmari reservoir. The simulation model was used to visualize the water front advance in order to evaluate the water production structurally. The numerical results also show that the channeling is the main cause of water production, as well as, oil-water contact advance problem was noted due to fault sealing behavior effects.


  • Open Access

    Modeling of Petrophysical Properties and Reserve Estimation of Mishrif Formation-Garraf Oil Field

    by Ahmed T Abeed, Samaher A Lazim, Ramzy S Hamied

    In this study a build-up a 3D geologic model both depend on the information of field and subsurface is a usual task in geologic studies including resource evaluation and hazard assessment. During this study a 3D geologic model for Mishrif Formation in Garraf oil field has been set-up by using petrel 2015 software system. Mishrif Formation represents the foremost important reservoir in Garraf oil field. Four vertical oil wells and one directional well were chosen in Garraf Oil Field so as to set-up structural and petrophysical models delineated by a 3D static geologic model in 3 dimensions. The structural closure is shifted from GA-3 well to GA-A1P well. Mishrif Formation was divided into 10 zones. Sequential Gaussian Simulation algorithm was used to build-up Petrophysical model (NTG, permeability, water saturation and porosity) for Mishrif Formation keeping with information analyses and also the results from modeling the units (M1.2, L1 and L1.2) are thought-about as prime quality reservoir units because of the high PHIE and low water saturation. Units (L2, L2.2, L2.3 and L2.4) are thought-about as poor reservoirs because of low PHIE and high water saturation, and non-reservoir units include (Top Mishrif, M1 and M2) thus, they represent cap units. Cross sections of petrophysical model were conducted to Illustrate the vertical and horizontal distribution of porosity, permeability, Net to gross and water saturation between wells within the field. This study calculated the reserves of the Mishrif formation of Garraf oilfield by petrel, that alter the issue that the reserves parameters are difficult to properly acquire when estimate complex reservoir’s reserves in terms of ancient volume technique.


  • Open Access

    Simulation and Mathematical Representation of N-Octane Aromatization on Ge-Re-Pt/Al2O3, Cs-Pt/ Al2O3,Re-Pt/ Al2O3 Catalysts

    by Ramzy S. Hamied

    In the present study mathematical representation was used to predict the reaction kinetics of the n-octane aromatization which tested with three types of catalysts by adding (Ge, Cs, and Re ) in order to improves the catalytic properties (enhanced the activity) of Pt/Al2O3 catalyst for n-octane aromatization. The aromatization process carried out in the range of reaction temperature varying from (425 to 500 °C) and weight hour space velocity varied from (0.6 to 1.2 hr-1) with hydrogen as the carrier gas at atmospheric pressure. The results showed that the higher conversion of n-octane aromatization increased with temperature increasing but at temperature higher than (500 °C) hydrocracking reaction is promoted. Whereas the effect of weight hourly space velocity has shown inverse impact on conversion. On the other hand the yield of aromatic increase especially benzene and toluene which produce as secondary products from the hydrogenolysis of A8 for three types of catalysts using in the process under the same operating condition. The simulation results of the model based on proposed kinetic model was compared with the experimental results. The comparison between the predicted and commercially results shows a good agreement with error% between (6.91 – 17.87).