Victor Moreno
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Victor Moreno has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Jean-Pierre Wolf
GAP–Biophotonics, Université de Genève, Geneva, Switzerland
2 shared publications - Malte C. Schroeder
Photonics and Ultrafast Laser Science, Ruhr-Universität Bochum 1 , Universitätsstr. 150, 44801 Bochum
2 shared publications - Alberto Pigazo
Department of Computer Science and Electronics, Universidad de Cantabria, Santander, Spain
1 shared publication Amirhossein Mostajabi
EMC Laboratory, Electrical Engineering Institute, Ecole Polytechnique Fédérale de Lausanne (EPFL), Lausanne, Switzerland
1 shared publicationAndré Mysyrowicz
Laboratoire d’Optique Appliquée – ENSTA Paris, Ecole Polytechnique, CNRS, IP Paris, Palaiseau, France
1 shared publicationAntonio Dell'Aquila
Dept. of Electrical and Electronic Engineering, Polytechnic of Bari, ITALY 70125
1 shared publication
Latest Publications
- Open Access
- 1 November 2023
- Published by AIP Publishing in APL Photonics
- Vol. 8 (11)
High-power sub-picosecond filamentation at 1.03 µ m with high repetition rates between 10 and 100 kHz
Filamentation has extensively been explored and is well understood at repetition rates <1 kHz due to the typical availability of multi-mJ laser systems at a moderate average power. The advent of high-power Yb-lasers opened new possibilities for filamentation research. However, so far, high average power Yb systems have mostly been explored to increase the driving pulse energy to several hundreds of mJ and not at significantly higher repetition rates. In this paper, we study, for the first time, long filaments at unprecedented high repetition rates of 10, 40, and 100 kHz using a 500-W Yb-doped thin-disk amplifier driver operating with sub-700 fs pulses. We compare the filament length, density hole, and fluorescence at a constant peak power but different repetition rates and find a strong dependence on filament length and density depletion with repetition rate. Our analysis reveals the emergence of a significant stationary density depletion at repetition rates of 40 and 100 kHz. The corresponding reduction in the breakdown threshold by increasing the laser repetition rate observed in our study signifies a promising avenue for enhancing the efficiency and reliability of electric discharge triggering in various scenarios. Using capacitive plasma probe measurements, we address the limitations of fluorescence imaging-based measurements and demonstrate a systematic underestimation of filament length. This work contributes to a deeper understanding of the interplay between laser repetition rates, filamentation, and heat-driven density depletion effects from high-repetition-rate high-power laser systems and will contribute to guiding future research, making use of filaments at high repetition rates.
- 1 November 2023
- Published by AIP Publishing in APL Photonics
- Vol. 8 (11)
Open AccessHigh-power sub-picosecond filamentation at 1.03 µ m with high repetition rates between 10 and 100 kHz
Filamentation has extensively been explored and is well understood at repetition rates <1 kHz due to the typical availability of multi-mJ laser systems at a moderate average power. The advent of high-power Yb-lasers opened new possibilities for filamentation research. However, so far, high average power Yb systems have mostly been explored to increase the driving pulse energy to several hundreds of mJ and not at significantly higher repetition rates. In this paper, we study, for the first time, long filaments at unprecedented high repetition rates of 10, 40, and 100 kHz using a 500-W Yb-doped thin-disk amplifier driver operating with sub-700 fs pulses. We compare the filament length, density hole, and fluorescence at a constant peak power but different repetition rates and find a strong dependence on filament length and density depletion with repetition rate. Our analysis reveals the emergence of a significant stationary density depletion at repetition rates of 40 and 100 kHz. The corresponding reduction in the breakdown threshold by increasing the laser repetition rate observed in our study signifies a promising avenue for enhancing the efficiency and reliability of electric discharge triggering in various scenarios. Using capacitive plasma probe measurements, we address the limitations of fluorescence imaging-based measurements and demonstrate a systematic underestimation of filament length. This work contributes to a deeper understanding of the interplay between laser repetition rates, filamentation, and heat-driven density depletion effects from high-repetition-rate high-power laser systems and will contribute to guiding future research, making use of filaments at high repetition rates.
- Top Cited PapersOpen Access
- 16 January 2023
- Published by Springer Nature in Nature Photonics
- Vol. 17 (3) , 231-235
Laser-guided lightning
Lightning discharges between charged clouds and the Earth’s surface are responsible for considerable damages and casualties. It is therefore important to develop better protection methods in addition to the traditional Franklin rod. Here we present the first demonstration that laser-induced filaments—formed in the sky by short and intense laser pulses—can guide lightning discharges over considerable distances. We believe that this experimental breakthrough will lead to progress in lightning protection and lightning physics. An experimental campaign was conducted on the Säntis mountain in north-eastern Switzerland during the summer of 2021 with a high-repetition-rate terawatt laser. The guiding of an upward negative lightning leader over a distance of 50 m was recorded by two separate high-speed cameras. The guiding of negative lightning leaders by laser filaments was corroborated in three other instances by very-high-frequency interferometric measurements, and the number of X-ray bursts detected during guided lightning events greatly increased. Although this research field has been very active for more than 20 years, this is the first field-result that experimentally demonstrates lightning guided by lasers. This work paves the way for new atmospheric applications of ultrashort lasers and represents an important step forward in the development of a laser based lightning protection for airports, launchpads or large infrastructures.
- 16 January 2023
- Published by Springer Nature in Nature Photonics
- Vol. 17 (3) , 231-235
Top Cited PapersOpen AccessLaser-guided lightning
Lightning discharges between charged clouds and the Earth’s surface are responsible for considerable damages and casualties. It is therefore important to develop better protection methods in addition to the traditional Franklin rod. Here we present the first demonstration that laser-induced filaments—formed in the sky by short and intense laser pulses—can guide lightning discharges over considerable distances. We believe that this experimental breakthrough will lead to progress in lightning protection and lightning physics. An experimental campaign was conducted on the Säntis mountain in north-eastern Switzerland during the summer of 2021 with a high-repetition-rate terawatt laser. The guiding of an upward negative lightning leader over a distance of 50 m was recorded by two separate high-speed cameras. The guiding of negative lightning leaders by laser filaments was corroborated in three other instances by very-high-frequency interferometric measurements, and the number of X-ray bursts detected during guided lightning events greatly increased. Although this research field has been very active for more than 20 years, this is the first field-result that experimentally demonstrates lightning guided by lasers. This work paves the way for new atmospheric applications of ultrashort lasers and represents an important step forward in the development of a laser based lightning protection for airports, launchpads or large infrastructures.
- 1 June 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 153 (21635137) , 2253-2257
FBD-method based controller for shunt active power filters in marine vessels
Shunt active power filters (SAPFs) based on the Fryze-Buchholz-Depenbrock (FBD) method allow electrical power quality (PQ) disturbances related to the load current consumption to be compensated. However, SAPF controllers based on this method require a stable grid fundamental frequency in order to operate properly. In case of isolated electrical grids suffering severe PQ disturbances, which is the case of ships electrical systems, the fundamental grid frequency can be very unstable, which reduces the SAPF performance due to an erroneous evaluation of the equivalent averaged load conductance (Ge). This paper presents a new approach for the evaluation of Ge which attenuates the impact of frequency variations. As a consequence, the performance of the SAPF is improved. Simulation results are given in order to evaluate the proposed controller.
- 1 June 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 153 (21635137) , 2253-2257
FBD-method based controller for shunt active power filters in marine vessels
Shunt active power filters (SAPFs) based on the Fryze-Buchholz-Depenbrock (FBD) method allow electrical power quality (PQ) disturbances related to the load current consumption to be compensated. However, SAPF controllers based on this method require a stable grid fundamental frequency in order to operate properly. In case of isolated electrical grids suffering severe PQ disturbances, which is the case of ships electrical systems, the fundamental grid frequency can be very unstable, which reduces the SAPF performance due to an erroneous evaluation of the equivalent averaged load conductance (Ge). This paper presents a new approach for the evaluation of Ge which attenuates the impact of frequency variations. As a consequence, the performance of the SAPF is improved. Simulation results are given in order to evaluate the proposed controller.