Daniel Bucur

Environmental pressures necessitate finding alternatives to Portland cement using alkali-activated aluminosilicate materials. Mortars containing different types of class F fly ash (Romania and Canada), furnace slag, silica fume and sand, activated with 5.1 M potassium hydroxide solution and 40% sodium silicate solution. Three mixes were tested (Mix 1 – fly ash Romania, Mix 2 - fly ash Canada and Mix 3 – fly ash Canada and slag). The activators were chosen to develop materials with high mechanical strength. The activation process occurred at controlled laboratory conditions (20 ± 2℃ and 65% relative humidity). Mix 3 showed the highest strength values of 43.8 MPa and a flexural strength of 7.4 MPa after 28 days. Mix 2 had a compressive strength of 26.0 MPa, in contrast to 8.3 MPa for Mix 1. The addition of blast furnace slag (Mix 3 vs. Mix 2) nearly doubled the compressive strength values. Proposed mixes are an effective alternative to cement mortar that reduce waste, through valorization of industrial by-products and diminish carbon dioxide emissions by 30%. Microstructural analyses (SEM and XRD) confirmed the formation of reaction products consistent with the observed mechanical strength. The developed mixes show promising mechanical performance and contribute to reducing CO₂ emissions in construction materials.

This study investigates the synergistic influence of multi-walled carbon nanotubes (MWC-NTs), nanosilica powder (NSP), and polypropylene fiber waste (PFW) on the mechanical performance of mortar incorporating demolished concrete waste aggregates (DCWA). The replacement of natural aggregates with DCWA typically results in strength reductions and weak interfacial transition zones; therefore, the combined use of nanomaterials and microfibers is proposed as a mitigation strategy. A Taguchi Design of Experiments (DOE) approach was employed to optimize mix parameters, including MWCNT dosage, NSP content, PFW volume fraction, and DCWA replacement level. Mortar mixtures were prepared with MWCNTs (0–0.1% by binder weight), NSP (0–2% by binder weight), PFW (0–0.3% by volume), and DCWA (0–20% replacement of fine sand). Mechanical performance was assessed through compressive and flexural strength tests. A combined statistical approach using the Pareto chart and ANOVA identified the most influential parameters and their respective contributions to the response variable. The innovative aspect of this research lies in the synergistic integration of MWCNTs, NSP, demolished concrete waste, and polypropylene fiber waste within the mortar matrix, with the incorporation of nanomaterials specifically intended to compensate for the strength reduction typically induced by the use of demolition concrete waste aggregates. Although a potential nano-scale synergy between MWCNTs and NSP was initially considered, the experimental results indicated that the most relevant synergistic effects occurred among broader mix parameters rather than specifically between the two nanomaterials. Even so, when assessed individually, both nanomaterials contributed to improving the mechanical characteristics of the mortar—particularly nanosilica, which demonstrated a more pronounced effect—yet these individual enhancements did not translate into a distinct synergistic interaction between MWCNTs and NSP. The Taguchi DOE proved to be an efficient tool for multiple factor analysis, enabling reliable identification of the most influential parameters with a minimum number of tests. Its application facilitated the development of mortar mixtures that effectively integrate demolition waste while achieving enhanced mechanical performance through nano- and micro-scale reinforcement.

Waste has become an everyday subject, especially its efficient recycling due to the increasing decline in the planet’s primary resources. Therefore, their recovery is intended to be total and with minimal energy consumption. Biomass waste is fully recoverable in raw or processed states and in combination with other compatible waste types (including wastewater from construction, polymers, and sunflower seeds). It represents the basic elements for obtaining synthetic wood to replace natural wood, which is very expensive and difficult to obtain (lasts for several years). This paper proposes three methods to determine the thermal conductivity of these new materials (synthetic wood) to guarantee and optimise their thermal characteristics. The determination of thermal characteristics in insulating materials is usually performed experimentally in a double climate chamber or more simply using a special instrument of the ISOMET type, but under these conditions, the sample must meet certain conditions imposed by the manufacturer to be tested. Thus, two experimental investigation methods are used to which a numerical method is added, which consists of modelling by the finite element method with an adequate programme of heat transfer through these materials. Four samples with variable content of recyclable waste obtained through combinations resulting from six different experimental design plans with two controlled factors were analysed to optimise synthetic wood recipes for the efficiency of their hygro-thermal characteristics. The content of the tested samples varied relative to the quantity and number of recyclable wastes included in the final recipe. Thus, the thermal conductivity obtained was different for each sample but close to that of similar synthetic wood-type materials and natural wood.

This study aimed to analyse the bioaccumulation of heavy metal ions in plants of spontaneous flora. An urban area was established from which soil samples were taken and analyses were performed on the content of heavy metal ions. The soil samples were collected from Iasi’s urban area to determine the heavy metal concentrations, obtain maps of sensitive land, and determine the content of heavy metals in spontaneous flora and transfer these into an aqueous extract. The investigation of heavy metal ion levels in certain plants revealed the following: (i) all plants from the Brassicaceae accumulate heavy metals, and B. juncea has a great ability to accumulate and transfer Cu, Cr(VI), Cd, Ni, Pb, and Zn towards the shoots; (ii) heavy metals (Fe, Cu, Cr, Mn, Zn) were present in variable concentrations, with mint and nettle being notable for their increased level of iron and thyme, and rattle for its zinc levels; (iii) toxic metals (Pb, Cd, Ni) are present in low concentrations in plants as well as in infusions, except for in primula and plantain, which do not have high levels of Pb and Cd. The results showed that values exceeded the maximum recommended values in areas with industrial pollution. Taking into account the potential for the bioaccumulation of heavy metal ions by plants from spontaneous flora and their use as medicinal plants, it is recommended, based on the studies conducted, to harvest and use plants from soils that do not contain heavy metal ions.

Waste is a major worldwide problem and its recycling has become mandatory in the current context of the decrease in natural resources. The management of recyclable waste improves the efficiency of any economic activities and the impact on the environment decreases proportionally to the quantities reused. With a significant impact on carbon dioxide emissions, the construction sector is one of the largest consumers of energy and raw materials. Hemp, and other biomass waste, are by-products in agriculture, making important contributions to the development of ecological materials by incorporating important quantities of such recyclable waste. This paper presents a series of different hemp concrete compositions that aim to obtain the optimum ratio between the binder and hemp shiv, in order to determine the inflection point towards which the delimitation can be made between insulating materials and materials with improved mechanical resistance. The importance of the work is given by the fact that, until now, the optimal proportion between the binder and hemp wood chips has not been demonstrated. This turning point must be justified by a variation of the mechanical resistance or a variation of the heat transfer coefficient, through the conductivity of the obtained samples. After preliminary testing, the statistical analysis will allow identification of the specific quantities needed to improve the physical-mechanical performance of the hemp-concrete recipe. Thus, by adding a justified amount of binder, an ecological material based on vegetable waste from agricultural crops is obtained. The material will have thermo-mechanical properties designed for a specific situation, required by the minimum performance imposed by the destination for which it will be made.

Sewage sludge (SS) has been connected to a variety of global environmental problems. Assessing the risk of various disposal techniques can be quite useful in recommending appropriate management. The preparation of sewage sludge biochar (SSB) and its impacts on soil characteristics, plant health, nutrient leaching, and greenhouse gas emissions (GHGs) are critically reviewed in this study. Comparing the features of SSB obtained at various pyrolysis temperatures revealed changes in its elemental content. Lower hydrogen/carbon ratios in SSB generated at higher pyrolysis temperatures point to the existence of more aromatic carbon molecules. Additionally, the preparation of SSB has an increased ash content, a lower yield, and a higher surface area as a result of the rise in pyrolysis temperature. The worldwide potential of SS output and CO₂-equivalent emissions in 2050 were predicted as factors of global population and common disposal management in order to create a futuristic strategy and cope with the quantity of abundant global SS. According to estimations, the worldwide SS output and associated CO₂-eq emissions were around 115 million tons dry solid (Mt DS) and 14,139 teragrams (Tg), respectively, in 2020. This quantity will rise to about 138 Mt DS sewage sludge and 16985 Tg CO₂-eq emissions in 2050, a 20% increase. In this regard, developing and populous countries may support economic growth by utilizing low-cost methods for producing biochar and employing it in local agriculture. To completely comprehend the benefits and drawbacks of SSB as a soil supplement, further study on long-term field applications of SSB is required.

Chemical nitrogen (N) fertilizers are regarded as one of the environmental contaminants in addition to the necessity for fossil sources for their production. Conversely, it is impossible to neglect the supply of nitrogen needed as one of the essential ingredients for plant function. For organic agriculture, it is crucial to use alternative fertilizer management to reduce the harmful impacts and production costs of chemical fertilizers. In a one-year pot experiment, nitrate (NO⁻₃) leaching and nitrogen efficiency of wheat were examined in relation to biochar (B) mixed with urea (U), legume residues (L), and azocompost (A), which represent chemical, green, and biological sources of N-fertilizers, respectively. Control (no biochar, no fertilizer), U (46 kg ha⁻¹), A (5 t ha⁻¹), L (5 t ha⁻¹), B (10 t ha⁻¹), UB, AB, and LB were the experimental treatments. Grain yield of wheat was enhanced by 337% and 312% with UB and UL, respectively. The LB produced the highest grain N yield, with a rise of 8.8 times over the control. L had the highest N-use efficiency, with an increase of 149% over the control. The highest N-harvest index and N-recovery efficiency were obtained by using LB, with values of 91 and 70 %, respectively. Nitrate leaching occurred in the following order: U > Control ≥ A ≥ L > UB > AB ≥ LB > B. Nitrogen is retained for the plant in the extensive specific surface of biochar when N-fertilizers are used in conjunction with them. This not only improves N-efficiency but also minimizes nitrogen loss through leaching. Additionally, the soil can benefit from the addition of leguminous organic fertilizer in a similar way as to urea fertilizer in terms of increasing wheat grain yield, particularly when combined with biochar.

The Congo Red dye was removed from a simulated textile wastewater solution using fly ash from a local power plant. The characterisation of fly ash was studied in detail by SEM, EDX, XRD, FTIR, BET surface area and TGA techniques. The influence of four parameters (contact time, initial concentration, adsorbent dose, and temperature) was analysed, the results showing that the adsorption capacity depends on these parameters. Thermodynamic and regeneration investigations as well are presented. The fit to pseudo-second-order kinetics models suggests that the removal process is a chemical adsorption. The Langmuir model fitted the experimental data, with a maximum adsorption capacity of 22.12 mg/g. The research is a preliminary case study that highlights that fly ash posed a very good potential as a material for Congo Red dye removal.

Land degradation through erosion processes is probably the most restrictive issue regarding the sustainable agricultural use of land resources in contemporary Romania. The socio-economic changes that occurred in Romanian society after 1990 resulted in a sharp decline in the implementation of conservation practices along with an increase in intensity of land degradation. Consequently, the present paper firstly aims to analyse the actual spread and intensity of land degradation in the Puriceni-Bahnari catchment, representative area in terms soil erosion within Moldavian Plateau of Eastern Romania. Secondly, the achievement of a dedicated project at the level of the entire basin regarding the implementation of land conservation practices is the most suitable solution for the sustainable agricultural use of this fragile natural resource. The results prove the severe degradation state of the agricultural land, with a mean value of annual soil loss of 15.46 t·ha⁻¹·yr⁻¹ (13,500 t·yr⁻¹). Furthermore, 460 ha of agricultural lands (72.7% of total) falls within the category that exceeds the limit of admissible erosion of 7 t·ha⁻¹·yr⁻¹. As a solution to the existing land use pattern, we designed a map of proposed conservation measures and works on agricultural land for the whole catchment that can be relatively easily implemented and conserve soil and water. The main issues of the proposed land use pattern are: (1) the entire cropland must be reduced and changed to a strip-cropping system; (2) the quality of the pastures should be improved; (3) the forested area must be substantially extended, especially on account of unproductive land, and (4) the agricultural road network must be halved and entirely reshaped. In conclusion, the large-scale implementation of conservation practices on degraded agricultural land is the only rational solution for sustainable development of poor local communities in the hilly areas from eastern Romania.

The initial characteristics of Romanian fly ash from the CET II Holboca power plant show the feasibility of its application for the production of a new material with applicability in environmental decontamination. The material obtained was characterized using standard techniques: scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), instrumental neutron activation analysis (INAA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), the Brunauer–Emmett–Teller (BET) surface area, and thermogravimetric differential thermal analysis (TG-DTA). The adsorption capacity of the obtained material was evaluated in batch systems with different values of the initial Cu(II) ion concentration, pH, adsorbent dose, and contact time in order to optimize the adsorption process. According to the experimental data presented in this study, the adsorbent synthesized has a high adsorption capacity for copper ions (q_max = 27.32–58.48 mg/g). The alkali treatment of fly ash with NaOH improved the adsorption capacity of the obtained material compared to that of the untreated fly ash. Based on the kinetics results, the adsorption of copper ions onto synthesized material indicated the chemisorption mechanism. Notably, fly ash can be considered an important beginning in obtaining new materials with applicability to wastewater treatment.