Li Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Li Zhou has a total of 94 co-authors. Here are the top co-authors by number of shared publications:
Yunshuo Cao
Yantai Univ, Sch Electromech & Automot Engn, Yantai 264005, Peoples R China
7 shared publicationsChengyu Song
Yantai Univ, Sch Electromech & Automot Engn, Yantai 264005, Shandong, Peoples R China
5 shared publicationsJigong Du
Yantai Univ, Sch Electromech & Automot Engn, Yantai 264005, Peoples R China
5 shared publicationsBin Wang
School of Electromechanical and Automotive Engineering, Yantai University, Yantai, China
4 shared publicationsMing Li
School of Electromechanical and Automotive Engineering, Yantai University, Yantai, P.R. China
4 shared publicationsMingyuan Zhang
4 shared publications
Latest Publications
- 9 March 2026
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 20 (5) , 2309-2333
Modeling of microstructure evolution of Ti65 alloy during high temperature compression
- 9 March 2026
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 20 (5) , 2309-2333
Modeling of microstructure evolution of Ti65 alloy during high temperature compression
- 9 March 2026
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 107 (2) , 927-938
Multi-Scale Modeling-Simulation of Positional Damage in Milling SiCp/Al Composite Thin-Walled Parts With Movable Auxiliary Support
- 9 March 2026
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 107 (2) , 927-938
Multi-Scale Modeling-Simulation of Positional Damage in Milling SiCp/Al Composite Thin-Walled Parts With Movable Auxiliary Support
- 16 July 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (9) , 4189-4203
Numerical Simulation and Experimental Analysis of Laser Welding of GH4099 Ni-Based Superalloy Thin Plate
- 16 July 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (9) , 4189-4203
Numerical Simulation and Experimental Analysis of Laser Welding of GH4099 Ni-Based Superalloy Thin Plate
- Open Access
- 23 February 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 35, 5440-5454
Experimental and simulation study on the deformation behavior, mechanical properties and microstructure of Ti–6Al–4V alloy wires fabricated by hot drawing
- 23 February 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 35, 5440-5454
Open AccessExperimental and simulation study on the deformation behavior, mechanical properties and microstructure of Ti–6Al–4V alloy wires fabricated by hot drawing
- 3 January 2025
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 106 (1) , 241-250
Forging Study of SiCp/Al Composite Bracket Arm
- 3 January 2025
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 106 (1) , 241-250
Forging Study of SiCp/Al Composite Bracket Arm
- Open Access
- 1 September 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (9) , 096512
Numerical and experimental study of temperature, residual stresses, and microstructural evolution on multi-layer and multi-pass laser cladding of 6061Al alloy
Multi-layer and multi-pass laser cladding is a promising and important process for repairing and strengthening Al alloy parts, whereas the temperature and residual stresses have a great influence on the properties of the laser cladding layer. In this paper, a nonlinear transient thermo-mechanical coupling finite element model of multi-layer and multi-pass cladding of 6061Al alloy was established. Meanwhile, the DFLUX user subroutine was developed using Fortran code to define the movement of the three-dimensional heat source model. From there, the distribution and evolution of temperature and stresses at different times were investigated. In addition, the micro-morphology and micro-hardness after cladding were also analyzed in detail. The results show that both the maximum residual tensile and compressive stresses decrease with increasing the number of cladding passes. At the same time, due to the reheating effect of each cladding on the previous cladding, a few bubbles appear at the top, middle and bottom of the overlap surfaces. Moreover, the micro-hardness of the overlap surfaces decreases slightly. This study can provide a theoretical basis for further research into multi-layer and multi-pass laser cladding of 6061Al alloy.
- 1 September 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (9) , 096512
Open AccessNumerical and experimental study of temperature, residual stresses, and microstructural evolution on multi-layer and multi-pass laser cladding of 6061Al alloy
Multi-layer and multi-pass laser cladding is a promising and important process for repairing and strengthening Al alloy parts, whereas the temperature and residual stresses have a great influence on the properties of the laser cladding layer. In this paper, a nonlinear transient thermo-mechanical coupling finite element model of multi-layer and multi-pass cladding of 6061Al alloy was established. Meanwhile, the DFLUX user subroutine was developed using Fortran code to define the movement of the three-dimensional heat source model. From there, the distribution and evolution of temperature and stresses at different times were investigated. In addition, the micro-morphology and micro-hardness after cladding were also analyzed in detail. The results show that both the maximum residual tensile and compressive stresses decrease with increasing the number of cladding passes. At the same time, due to the reheating effect of each cladding on the previous cladding, a few bubbles appear at the top, middle and bottom of the overlap surfaces. Moreover, the micro-hardness of the overlap surfaces decreases slightly. This study can provide a theoretical basis for further research into multi-layer and multi-pass laser cladding of 6061Al alloy.
- Open Access
- 5 March 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 29, 5271-5281
Optimization of hot deformation parameters for multi-directional forging of Ti65 alloy based on the integration of processing maps and finite element method
- 5 March 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 29, 5271-5281
Open AccessOptimization of hot deformation parameters for multi-directional forging of Ti65 alloy based on the integration of processing maps and finite element method
- 12 December 2023
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 18 (2) , 685-696
Numerical simulation of continuous hot rolling process for ultra-thick SiCp/2009Al composites plate
- 12 December 2023
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 18 (2) , 685-696
Numerical simulation of continuous hot rolling process for ultra-thick SiCp/2009Al composites plate
- Open Access
- 2 September 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 26, 6096-6107
Effects of different friction stir welding processes on residual stress and deformation of Ti62A alloy joints
- 2 September 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 26, 6096-6107
Open AccessEffects of different friction stir welding processes on residual stress and deformation of Ti62A alloy joints