Swapneel Danayat
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Swapneel Danayat has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Avinash Nayal
School of Aerospace and Mechanical Engineering, University of Oklahoma, Norman, OK, USA
6 shared publications - Fatema Tarannum
Ralph E. Martin Department of Chemical Engineering, University of Arkansas, Fayetteville, AR 72701, USA
6 shared publications - Jivtesh Garg
School of Aerospace and Mechanical Engineering, University of Oklahoma, Norman, OK 73019, USA
6 shared publications - Roshan Sameer Annam
School of Aerospace and Mechanical Engineering, University of Oklahoma, Norman, OK, USA
5 shared publications - Rajmohan Muthaiah
School of Aerospace and Mechanical Engineering, University of Oklahoma, Norman, OK 73019, USA
4 shared publications Jivtesh Garg
2 shared publications
Latest Publications
- Open Access
- 23 September 2026
- Published by Elsevier in SSRN Electronic Journal
Optimization of Thermal Conductivity Enhancement in Paraffin Wax and Epoxy Composites Using Expanded Graphite from Short H2O2-Assisted Intercalation
In this study, we investigate optimization of short-duration H₂O₂-assisted intercalation for producing expanded graphite (EG) fillers for maximum enhancement in thermal conductivity of paraffin wax/EG and epoxy/EG composites. Intercalation conditions were optimized in two stages: first, by varying the H₂SO₄:H₂O₂ volume ratio and then the reaction time. Volume ratio optimization of paraffin wax/EG composites identified an H₂SO₄:H₂O₂ volume ratio of 4:1 as the best ratio within the tested set, and this ratio was subsequently used for the reaction-time optimization study. Maxima in thermal diffusivity with respect to reaction (intercalation) time occurred at 5 mins for paraffin wax/EG and 6 mins for epoxy/EG composites. Under these conditions, the thermal conductivity reached 11.71 W m⁻¹ K⁻¹ for paraffin wax/EG at 15 wt% EG and 5.15 W m⁻¹ K⁻¹ for epoxy/EG at 10 wt% EG, indicating substantial enhancements over the pristine matrices. The results support an empirical optimum-window in which short H₂O₂-assisted intercalation provides sufficient expansion of expanded graphite which contributes to improved thermal conductivity. These findings provide a practical processing route for achieving highly thermally conductive EG-polymer composites.
- 23 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOptimization of Thermal Conductivity Enhancement in Paraffin Wax and Epoxy Composites Using Expanded Graphite from Short H2O2-Assisted Intercalation
In this study, we investigate optimization of short-duration H₂O₂-assisted intercalation for producing expanded graphite (EG) fillers for maximum enhancement in thermal conductivity of paraffin wax/EG and epoxy/EG composites. Intercalation conditions were optimized in two stages: first, by varying the H₂SO₄:H₂O₂ volume ratio and then the reaction time. Volume ratio optimization of paraffin wax/EG composites identified an H₂SO₄:H₂O₂ volume ratio of 4:1 as the best ratio within the tested set, and this ratio was subsequently used for the reaction-time optimization study. Maxima in thermal diffusivity with respect to reaction (intercalation) time occurred at 5 mins for paraffin wax/EG and 6 mins for epoxy/EG composites. Under these conditions, the thermal conductivity reached 11.71 W m⁻¹ K⁻¹ for paraffin wax/EG at 15 wt% EG and 5.15 W m⁻¹ K⁻¹ for epoxy/EG at 10 wt% EG, indicating substantial enhancements over the pristine matrices. The results support an empirical optimum-window in which short H₂O₂-assisted intercalation provides sufficient expansion of expanded graphite which contributes to improved thermal conductivity. These findings provide a practical processing route for achieving highly thermally conductive EG-polymer composites.
- Open Access
- 13 September 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 1420-1435
Hydrogen-peroxide intercalated expanded graphite facilitates large enhancement in thermal conductivity of polyetherimide/graphite nanocomposites
- 13 September 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 1420-1435
Open AccessHydrogen-peroxide intercalated expanded graphite facilitates large enhancement in thermal conductivity of polyetherimide/graphite nanocomposites
- 17 June 2024
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 16 (29) , 13755-13783
Role of four-phonon processes in thermal conductivity of two-dimensional materials and thermal-transport enhancement arising from interconnected nanofiller networks in polymer/nanofiller composites
Recent research has shed light on the importance of four-phonon scattering processes in the thermal conductivity (k) of 2D materials. The inclusion of 4 phonon scattering processes from first-principles has been shown to lead to a thermal conductivity of ∼1290 W m−1 K−1 in graphene at 300 K, significantly lower than the values predicted to be in excess of 4000 W m−1 K−1 based only on 3 phonon scattering processes. Four phonon processes are shown to be most significant for flexural ZA phonon modes, where the reflection symmetry selection rule (RSSR) is less restrictive for 4-phonon than 3-phonon scattering processes. This combined with the low frequencies of ZA phonon modes, leading to high populations, leads to higher 4-phonon than 3-phonon scattering of low frequency ZA phonon modes in graphene at 300 K. In this review, the role of parameters such as atomic structure, phonon dispersion and temperature on 4-phonon scattering processes in a wide range of 2D materials is reviewed. Materials such as graphene nanoplatelets (GnPs) have been extensively investigated for enhancement of the thermal conductivity of polymer composites. However, such enhancement is limited by the poor interfacial thermal conductance between the polymer and filler material. Interconnected filler networks overcome this issue through highly efficient continuous percolative heat transfer paths throughout the composite. Such 3D networks have been shown to enable ultra-high polymer thermal conductivities, approaching ∼100 W m−1 K−1, and even exceeding those of several metals. In this review, different techniques used to achieve such interconnected 3D filler networks, namely, aerogels, foams, ice-templating, expanded graphite, hot pressing of filler coated polymer particles, the synergistic effect between multiple fillers, and the stitching of filler sheets, are discussed and their impact on thermal conductivity enhancement are presented.
- 17 June 2024
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 16 (29) , 13755-13783
Role of four-phonon processes in thermal conductivity of two-dimensional materials and thermal-transport enhancement arising from interconnected nanofiller networks in polymer/nanofiller composites
Recent research has shed light on the importance of four-phonon scattering processes in the thermal conductivity (k) of 2D materials. The inclusion of 4 phonon scattering processes from first-principles has been shown to lead to a thermal conductivity of ∼1290 W m−1 K−1 in graphene at 300 K, significantly lower than the values predicted to be in excess of 4000 W m−1 K−1 based only on 3 phonon scattering processes. Four phonon processes are shown to be most significant for flexural ZA phonon modes, where the reflection symmetry selection rule (RSSR) is less restrictive for 4-phonon than 3-phonon scattering processes. This combined with the low frequencies of ZA phonon modes, leading to high populations, leads to higher 4-phonon than 3-phonon scattering of low frequency ZA phonon modes in graphene at 300 K. In this review, the role of parameters such as atomic structure, phonon dispersion and temperature on 4-phonon scattering processes in a wide range of 2D materials is reviewed. Materials such as graphene nanoplatelets (GnPs) have been extensively investigated for enhancement of the thermal conductivity of polymer composites. However, such enhancement is limited by the poor interfacial thermal conductance between the polymer and filler material. Interconnected filler networks overcome this issue through highly efficient continuous percolative heat transfer paths throughout the composite. Such 3D networks have been shown to enable ultra-high polymer thermal conductivities, approaching ∼100 W m−1 K−1, and even exceeding those of several metals. In this review, different techniques used to achieve such interconnected 3D filler networks, namely, aerogels, foams, ice-templating, expanded graphite, hot pressing of filler coated polymer particles, the synergistic effect between multiple fillers, and the stitching of filler sheets, are discussed and their impact on thermal conductivity enhancement are presented.
- Open Access
- 27 February 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (2)
Thickness dependent thermal conductivity of strontium titanate thin films on silicon substrate
Perovskite materials, of which strontium titanate (STO) and its thin films are an example, have attracted significant scientific interest because of their desirable properties and the potential to tune thermal conductivity by employing several techniques. Notably, strontium titanate thin films on silicon (Si) substrates serve as a fundamental platform for integrating various oxides onto Si substrates, making it crucial to understand the thermal properties of STO on Si. This work investigates the thermal conductivity of STO thin films on an Si substrate for varying film thicknesses (12, 50, 80, and 200 nm) at room temperature (∼300 K). The thin films are deposited using molecular beam epitaxy on the Si substrate and their thermal conductivity is characterized using the frequency domain thermoreflectance (FDTR) method. The measured values range from 7.4 ± 0.74 for the 200 nm thick film to 0.8 ± 0.1 W m−1 K−1 for the 12 nm thick film, showing a large effect of the film thickness on the thermal conductivity values. The trend of the values is diminishing with the corresponding decrease in the thin film thickness, with a reduction of 38%–93% in the thermal conductivity values, for film thicknesses ranging from 200 to 12 nm. This reduction in the values is relative to the bulk single crystal values of STO, which may range from 11 to 13.5 W m−1 K−1 [Yu et al., Appl. Phys. Lett. 92, 191911 (2008) and Fumega et al., Phys. Rev. Mater. 4, 033606 (2020)], as measured by our FDTR-based experiment. The study also explores the evaluation of volumetric heat capacity (Cp). The measured volumetric heat capacity for the 200 nm thin film is 3.07 MJ m−3 K−1, which is in reasonable agreement with the values available in the literature.
- 27 February 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (2)
Open AccessThickness dependent thermal conductivity of strontium titanate thin films on silicon substrate
Perovskite materials, of which strontium titanate (STO) and its thin films are an example, have attracted significant scientific interest because of their desirable properties and the potential to tune thermal conductivity by employing several techniques. Notably, strontium titanate thin films on silicon (Si) substrates serve as a fundamental platform for integrating various oxides onto Si substrates, making it crucial to understand the thermal properties of STO on Si. This work investigates the thermal conductivity of STO thin films on an Si substrate for varying film thicknesses (12, 50, 80, and 200 nm) at room temperature (∼300 K). The thin films are deposited using molecular beam epitaxy on the Si substrate and their thermal conductivity is characterized using the frequency domain thermoreflectance (FDTR) method. The measured values range from 7.4 ± 0.74 for the 200 nm thick film to 0.8 ± 0.1 W m−1 K−1 for the 12 nm thick film, showing a large effect of the film thickness on the thermal conductivity values. The trend of the values is diminishing with the corresponding decrease in the thin film thickness, with a reduction of 38%–93% in the thermal conductivity values, for film thicknesses ranging from 200 to 12 nm. This reduction in the values is relative to the bulk single crystal values of STO, which may range from 11 to 13.5 W m−1 K−1 [Yu et al., Appl. Phys. Lett. 92, 191911 (2008) and Fumega et al., Phys. Rev. Mater. 4, 033606 (2020)], as measured by our FDTR-based experiment. The study also explores the evaluation of volumetric heat capacity (Cp). The measured volumetric heat capacity for the 200 nm thin film is 3.07 MJ m−3 K−1, which is in reasonable agreement with the values available in the literature.
- 18 January 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 298
Thermally expanded graphite polyetherimide composite with superior electrical and thermal conductivity
- 18 January 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 298
Thermally expanded graphite polyetherimide composite with superior electrical and thermal conductivity
- Open Access
Superior enhancement in thermal conductivity of epoxy/graphene nanocomposites through use of dimethylformamide (DMF) relative to acetone as solvent
In this work, we demonstrate that use of dimethylformamide (DMF) as a solvent leads to better dispersion of graphene nanoplatelets in epoxy matrix compared to acetone solvent, in turn leading to higher thermal conductivity epoxy-graphene nanocomposites. While role of solvents in enabling superior mechanical properties has been addressed before, outlined study is the first to address the effect of solvents on thermal conductivity enhancement and provides novel pathways for achieving high thermal conductivity polymer composite materials. Uniform dispersion of graphene nanoparticles into epoxy can improve thermal contact with polymer leading to superior interface thermal conductance between polymer matrix and graphene. Organic solvents are typically employed to achieve efficient dispersion of graphene into the epoxy matrix. In this study, we compare the effect of two organic solvents, dimethylformamide (DMF) and acetone, in terms of their efficiency in dispersing graphene into the epoxy matrix and their effect on enhancing thermal conductivity of the composite. We find that polymer-graphene composites made with DMF solvent show 44% higher thermal conductivity compared to those made using acetone at 7 weight% filler composition. Laser scanning confocal microscopy (LSCM) imaging reveals that graphene-epoxy composites, prepared using DMF as solvent, exhibit more uniform dispersion of graphene-nanoplatelets compared to the case of acetone with acetone-based samples exhibiting up to 211% larger graphene agglomerations. Comparison with effective medium theory reveals an almost 35% lower interface thermal resistance between graphene and epoxy for DMF relative to acetone prepared composite. These results provide fundamentally new avenues to achieve higher thermal conductivity graphene-epoxy composites, of key importance for a wide range of thermal management technologies.
Open AccessSuperior enhancement in thermal conductivity of epoxy/graphene nanocomposites through use of dimethylformamide (DMF) relative to acetone as solvent
In this work, we demonstrate that use of dimethylformamide (DMF) as a solvent leads to better dispersion of graphene nanoplatelets in epoxy matrix compared to acetone solvent, in turn leading to higher thermal conductivity epoxy-graphene nanocomposites. While role of solvents in enabling superior mechanical properties has been addressed before, outlined study is the first to address the effect of solvents on thermal conductivity enhancement and provides novel pathways for achieving high thermal conductivity polymer composite materials. Uniform dispersion of graphene nanoparticles into epoxy can improve thermal contact with polymer leading to superior interface thermal conductance between polymer matrix and graphene. Organic solvents are typically employed to achieve efficient dispersion of graphene into the epoxy matrix. In this study, we compare the effect of two organic solvents, dimethylformamide (DMF) and acetone, in terms of their efficiency in dispersing graphene into the epoxy matrix and their effect on enhancing thermal conductivity of the composite. We find that polymer-graphene composites made with DMF solvent show 44% higher thermal conductivity compared to those made using acetone at 7 weight% filler composition. Laser scanning confocal microscopy (LSCM) imaging reveals that graphene-epoxy composites, prepared using DMF as solvent, exhibit more uniform dispersion of graphene-nanoplatelets compared to the case of acetone with acetone-based samples exhibiting up to 211% larger graphene agglomerations. Comparison with effective medium theory reveals an almost 35% lower interface thermal resistance between graphene and epoxy for DMF relative to acetone prepared composite. These results provide fundamentally new avenues to achieve higher thermal conductivity graphene-epoxy composites, of key importance for a wide range of thermal management technologies.
- Open Access
- 30 May 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (11) , 1877
Large Enhancement in Thermal Conductivity of Solvent−Cast Expanded Graphite/Polyetherimide Composites
We demonstrate in this work that expanded graphite (EG) can lead to a very large enhancement in thermal conductivity of polyetherimide−graphene and epoxy−graphene nanocomposites prepared via solvent casting technique. A k value of 6.6 Wm−1K−1 is achieved for 10 wt% composition sample, representing an enhancement of ~2770% over pristine polyetherimide (k~0.23 Wm−1K−1). This extraordinary enhancement in thermal conductivity is shown to be due to a network of continuous graphene sheets over long−length scales, resulting in low thermal contact resistance at bends/turns due to the graphene sheets being covalently bonded at such junctions. Solvent casting offers the advantage of preserving the porous structure of expanded graphite in the composite, resulting in the above highly thermally conductive interpenetrating network of graphene and polymer. Solvent casting also does not break down the expanded graphite particles due to minimal forces involved, allowing for efficient heat transfer over long−length scales, further enhancing overall composite thermal conductivity. Comparisons with a recently introduced effective medium model show a very high value of predicted particle–particle interfacial conductance, providing evidence for efficient interfacial thermal transport in expanded graphite composites. Field emission environmental scanning electron microscopy (FE−ESEM) is used to provide a detailed understanding of the interpenetrating graphene−polymer structure in the expanded graphite composite. These results open up novel avenues for achieving high thermal conductivity polymer composites.- 30 May 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (11) , 1877
Open AccessLarge Enhancement in Thermal Conductivity of Solvent−Cast Expanded Graphite/Polyetherimide Composites
We demonstrate in this work that expanded graphite (EG) can lead to a very large enhancement in thermal conductivity of polyetherimide−graphene and epoxy−graphene nanocomposites prepared via solvent casting technique. A k value of 6.6 Wm−1K−1 is achieved for 10 wt% composition sample, representing an enhancement of ~2770% over pristine polyetherimide (k~0.23 Wm−1K−1). This extraordinary enhancement in thermal conductivity is shown to be due to a network of continuous graphene sheets over long−length scales, resulting in low thermal contact resistance at bends/turns due to the graphene sheets being covalently bonded at such junctions. Solvent casting offers the advantage of preserving the porous structure of expanded graphite in the composite, resulting in the above highly thermally conductive interpenetrating network of graphene and polymer. Solvent casting also does not break down the expanded graphite particles due to minimal forces involved, allowing for efficient heat transfer over long−length scales, further enhancing overall composite thermal conductivity. Comparisons with a recently introduced effective medium model show a very high value of predicted particle–particle interfacial conductance, providing evidence for efficient interfacial thermal transport in expanded graphite composites. Field emission environmental scanning electron microscopy (FE−ESEM) is used to provide a detailed understanding of the interpenetrating graphene−polymer structure in the expanded graphite composite. These results open up novel avenues for achieving high thermal conductivity polymer composites. - Open Access
Superior effect of edge relative to basal plane functionalization of graphene in enhancing polymer-graphene nanocomposite thermal conductivity-A combined molecular dynamics and Greens functions study
To achieve high thermal conductivity (k) of polymer graphene nanocomposites, it is critically important to achieve efficient thermal coupling between graphene and its surrounding polymers through effective functionalization schemes. In this work, we demonstrate that edge-functionalization of graphene nanoplatelets (GnPs) can enable a larger enhancement of effective thermal conductivity in polymer-graphene nanocomposites, relative to basal plane functionalization. Effective thermal conductivity for edge case is predicted, through molecular dynamics simulations, to be up to 48% higher relative to basal plane bonding for 35 wt.% graphene loading with 10 layers thick nanoplatelets. This unique result opens up promising new avenues for achieving high thermal-conductivity polymer materials, which is of key importance for a wide range of thermal management technologies. The anisotropy of thermal transport in single layer graphene leads to very high in-plane thermal conductivity (~2000 W/mK) compared to the low out-of-plane thermal conductivity (~10 W/mK). Likewise, in multilayer graphene nanoplatelet (GnP), the thermal conductivity across the layers is even lower due to the weak van der Waals bonding between each pair of layers. Edge functionalization couples the polymer chains to the high in-plane thermal conduction pathway of graphene, thus leading to high overall high composite thermal conductivity. Basal-plane functionalization, however, lowers the thermal resistance between the polymer and the surface graphene sheets of the nanoplatelet only, causing the heat conduction through inner layers to be less efficient, thus resulting in basal plane scheme to be outperformed by edge scheme. The present study fundamentally enables novel pathways for achieving high thermal-conductivity polymer composites.
Open AccessSuperior effect of edge relative to basal plane functionalization of graphene in enhancing polymer-graphene nanocomposite thermal conductivity-A combined molecular dynamics and Greens functions study
To achieve high thermal conductivity (k) of polymer graphene nanocomposites, it is critically important to achieve efficient thermal coupling between graphene and its surrounding polymers through effective functionalization schemes. In this work, we demonstrate that edge-functionalization of graphene nanoplatelets (GnPs) can enable a larger enhancement of effective thermal conductivity in polymer-graphene nanocomposites, relative to basal plane functionalization. Effective thermal conductivity for edge case is predicted, through molecular dynamics simulations, to be up to 48% higher relative to basal plane bonding for 35 wt.% graphene loading with 10 layers thick nanoplatelets. This unique result opens up promising new avenues for achieving high thermal-conductivity polymer materials, which is of key importance for a wide range of thermal management technologies. The anisotropy of thermal transport in single layer graphene leads to very high in-plane thermal conductivity (~2000 W/mK) compared to the low out-of-plane thermal conductivity (~10 W/mK). Likewise, in multilayer graphene nanoplatelet (GnP), the thermal conductivity across the layers is even lower due to the weak van der Waals bonding between each pair of layers. Edge functionalization couples the polymer chains to the high in-plane thermal conduction pathway of graphene, thus leading to high overall high composite thermal conductivity. Basal-plane functionalization, however, lowers the thermal resistance between the polymer and the surface graphene sheets of the nanoplatelet only, causing the heat conduction through inner layers to be less efficient, thus resulting in basal plane scheme to be outperformed by edge scheme. The present study fundamentally enables novel pathways for achieving high thermal-conductivity polymer composites.