Sandip Mazumder
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sandip Mazumder has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Ankan Kumar
Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43210, United States
7 shared publications- Sai Kamarajugadda
Ohio State University, Columbus, OH
3 shared publications Arpit Mittal
Fellow ASME Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43210
2 shared publications- Dhaval Vaishnav
Ford Motor Company , 2400 Village Road, Dearborn, MI 48121
2 shared publications - Gurpreet Matharu
Ford Motor Company , 2400 Village Road, Dearborn, MI 48121
2 shared publications Mahesh Ravishankar
Department of Mechanical Engineering, The Ohio State University, Columbus, OH 43210
2 shared publications
Latest Publications
- 14 April 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 265
Numerical investigation of radiation effects in ammonia–methane–hydrogen combustion
- 14 April 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 265
Numerical investigation of radiation effects in ammonia–methane–hydrogen combustion
- 1 May 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 61 (3) , 839-846
Multiscale Model for Hydrogen Chloride Uptake on Aluminum for Spacecraft Fire Safety
An electrical fire within spacecraft environments often produces poisonous gases, such as hydrogen chloride (HCl). These gases adsorb on the interior materials of the spacecraft, primarily treated aluminum surfaces. A safe design of the spacecraft can be facilitated by modeling the spacecraft compartment. In this study, a multiscale model is developed to predict HCl uptake by anodized aluminum, which has a thick oxide layer covering its surface compared to other treatments. X-ray photoelectron spectroscopy revealed that aluminum chloride is found deep in the oxide layer of anodized aluminum, implying that the pore-scale transport and reaction of HCl within the oxide layer covering the aluminum surface must be considered. Hence, a multiscale approach is warranted. A pore-scale model is first developed, wherein the HCl reacts with the aluminum oxide pore walls to create an aluminum chloride layer. The HCl then diffuses through that layer for further reaction, until the layer (diffusion resistance) grows too large and the uptake of HCl stops. This pore-scale model is coupled with a reactor-scale model to predict overall HCl uptake. Results show that this new multiscale approach predicts the uptake of HCl far more accurately when compared to experimental data than previously used single (reactor)-scale models.
- 1 May 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 61 (3) , 839-846
Multiscale Model for Hydrogen Chloride Uptake on Aluminum for Spacecraft Fire Safety
An electrical fire within spacecraft environments often produces poisonous gases, such as hydrogen chloride (HCl). These gases adsorb on the interior materials of the spacecraft, primarily treated aluminum surfaces. A safe design of the spacecraft can be facilitated by modeling the spacecraft compartment. In this study, a multiscale model is developed to predict HCl uptake by anodized aluminum, which has a thick oxide layer covering its surface compared to other treatments. X-ray photoelectron spectroscopy revealed that aluminum chloride is found deep in the oxide layer of anodized aluminum, implying that the pore-scale transport and reaction of HCl within the oxide layer covering the aluminum surface must be considered. Hence, a multiscale approach is warranted. A pore-scale model is first developed, wherein the HCl reacts with the aluminum oxide pore walls to create an aluminum chloride layer. The HCl then diffuses through that layer for further reaction, until the layer (diffusion resistance) grows too large and the uptake of HCl stops. This pore-scale model is coupled with a reactor-scale model to predict overall HCl uptake. Results show that this new multiscale approach predicts the uptake of HCl far more accurately when compared to experimental data than previously used single (reactor)-scale models.
- Open Access
- 21 June 2023
- Published by Association for Computing Machinery (ACM)
- p. 215-226
Scalable parallelization for the solution of phonon Boltzmann Transport Equation
- 21 June 2023
- Published by Association for Computing Machinery (ACM)
- p. 215-226
Open AccessScalable parallelization for the solution of phonon Boltzmann Transport Equation
- Open Access
Modeling Thermal Radiation in Combustion Environments: Progress and Challenges
Modeling thermal radiation in combustion environments can be extremely challenging for two main reasons. First, the radiative transfer equation (RTE), which is the cornerstone of modeling radiation in such environments, is a five-dimensional integro-differential equation. Second, the absorption and scattering coefficients of molecular gases and particulates prevalent in combustion environments oscillate strongly with the wavenumber (or wavelength), i.e., the medium is strongly nongray, requiring the solution of the RTE for a large number of wavenumbers. This article reviews the progress that has been made in this area to date with an emphasis on the work performed over the past three decades. Progress in both deterministic and stochastic (Monte Carlo) solutions of the RTE is reviewed, in addition to the review of the treatment of the spectral properties of gases, soot, and fuel droplets that dominate combustion environments, i.e., spectral or nongray models. The application of the various state-of-the-art nongray models and RTE solution methods to flames (particularly turbulent), fires, combustors, and other combustion systems are summarized along with a critical discussion of the pros and cons of the models and methods. Finally, the challenges that remain in modeling thermal radiation in combustion systems are highlighted and future outlooks are shared.
Open AccessModeling Thermal Radiation in Combustion Environments: Progress and Challenges
Modeling thermal radiation in combustion environments can be extremely challenging for two main reasons. First, the radiative transfer equation (RTE), which is the cornerstone of modeling radiation in such environments, is a five-dimensional integro-differential equation. Second, the absorption and scattering coefficients of molecular gases and particulates prevalent in combustion environments oscillate strongly with the wavenumber (or wavelength), i.e., the medium is strongly nongray, requiring the solution of the RTE for a large number of wavenumbers. This article reviews the progress that has been made in this area to date with an emphasis on the work performed over the past three decades. Progress in both deterministic and stochastic (Monte Carlo) solutions of the RTE is reviewed, in addition to the review of the treatment of the spectral properties of gases, soot, and fuel droplets that dominate combustion environments, i.e., spectral or nongray models. The application of the various state-of-the-art nongray models and RTE solution methods to flames (particularly turbulent), fires, combustors, and other combustion systems are summarized along with a critical discussion of the pros and cons of the models and methods. Finally, the challenges that remain in modeling thermal radiation in combustion systems are highlighted and future outlooks are shared.
- 14 June 2022
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 14 (11) , 1-32
Efficient Simulation of Freezing of Water in Large Tanks Including Expansion of Ice
A liquid water-urea mixture is stored onboard diesel vehicles and used for exhaust aftertreatment. In cold weather conditions, the mixture may freeze and the freezing process may span over a day. In the first part of our study (Journal of Thermal Science and Engineering Applications—Transactions of the ASME, Vol. 13, p. 011008, 2021), it was shown that traditional computational methods are impractical for modeling such large-duration freezing processes because of restrictions in the time-step size posed by numerical stability and physical time scale considerations. A model, in which natural convection driven thermal transport is treated as a diffusive process, was developed and demonstrated. Since the flow field was not computed in this model, the computations were found to be orders of magnitude more efficient than traditional methods. This preliminary model did not account for the expansion of ice. Here, a new model that accounts for the expansion of ice, and the consequent rise of the initial air-water/ice interface (ice dome formation) is presented. An additional conservation equation for excess volume fraction is introduced to this end and is solved using the unstructured finite-volume procedure and sub-time-stepping. Since the flow field is not computed, the air-water/ice interface is tracked using a new algorithm similar to the traditional volume-of-fluid (VOF) method, but one that constructs fluxes using a diffusive formulation rather than an advective one. Validation studies in full-scale three-dimensional tanks show good agreement with measured temperature-time data. It is found that the air-water/ice interface first evolves to a concave shape before finally becoming a convex ice dome after full solidification.
- 14 June 2022
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 14 (11) , 1-32
Efficient Simulation of Freezing of Water in Large Tanks Including Expansion of Ice
A liquid water-urea mixture is stored onboard diesel vehicles and used for exhaust aftertreatment. In cold weather conditions, the mixture may freeze and the freezing process may span over a day. In the first part of our study (Journal of Thermal Science and Engineering Applications—Transactions of the ASME, Vol. 13, p. 011008, 2021), it was shown that traditional computational methods are impractical for modeling such large-duration freezing processes because of restrictions in the time-step size posed by numerical stability and physical time scale considerations. A model, in which natural convection driven thermal transport is treated as a diffusive process, was developed and demonstrated. Since the flow field was not computed in this model, the computations were found to be orders of magnitude more efficient than traditional methods. This preliminary model did not account for the expansion of ice. Here, a new model that accounts for the expansion of ice, and the consequent rise of the initial air-water/ice interface (ice dome formation) is presented. An additional conservation equation for excess volume fraction is introduced to this end and is solved using the unstructured finite-volume procedure and sub-time-stepping. Since the flow field is not computed, the air-water/ice interface is tracked using a new algorithm similar to the traditional volume-of-fluid (VOF) method, but one that constructs fluxes using a diffusive formulation rather than an advective one. Validation studies in full-scale three-dimensional tanks show good agreement with measured temperature-time data. It is found that the air-water/ice interface first evolves to a concave shape before finally becoming a convex ice dome after full solidification.
- 8 November 2021
- Published by Wiley in Journal of Heat Transfer
- Vol. 144 (1)
On the Determination of Thermal Conductivity From Frequency Domain Thermoreflectance Experiments
The Fourier and the hyperbolic heat conduction equations were solved numerically to simulate a frequency-domain thermoreflectance (FDTR) experiment. Numerical solutions enable isolation of pump and probe laser spot size effects and use of realistic boundary conditions. The equations were solved in time domain and the phase lag between the temperature of the transducer (averaged over the probe laser spot) and the modulated pump laser signal was computed for a modulation frequency range of 200 kHz–200 MHz. Numerical calculations showed that extracted values of the thermal conductivity are sensitive to both the pump and probe laser spot sizes, while analytical solutions (based on Hankel transform) cannot isolate the two effects. However, for the same effective (combined) spot size, the two solutions are found to be in excellent agreement. If the substrate (computational domain) is sufficiently large, the far-field boundary conditions were found to have no effect on the computed phase lag. The interface conductance between the transducer and the substrate was found to have some effect on the extracted thermal conductivity. The hyperbolic heat conduction equation yielded almost the same results as the Fourier heat conduction equation for the particular case studied. The numerically extracted thermal conductivity value (best fit) for the silicon substrate considered in this study was found to be about 82–108 W/m/K, depending on the pump and probe laser spot sizes used.
- 8 November 2021
- Published by Wiley in Journal of Heat Transfer
- Vol. 144 (1)
On the Determination of Thermal Conductivity From Frequency Domain Thermoreflectance Experiments
The Fourier and the hyperbolic heat conduction equations were solved numerically to simulate a frequency-domain thermoreflectance (FDTR) experiment. Numerical solutions enable isolation of pump and probe laser spot size effects and use of realistic boundary conditions. The equations were solved in time domain and the phase lag between the temperature of the transducer (averaged over the probe laser spot) and the modulated pump laser signal was computed for a modulation frequency range of 200 kHz–200 MHz. Numerical calculations showed that extracted values of the thermal conductivity are sensitive to both the pump and probe laser spot sizes, while analytical solutions (based on Hankel transform) cannot isolate the two effects. However, for the same effective (combined) spot size, the two solutions are found to be in excellent agreement. If the substrate (computational domain) is sufficiently large, the far-field boundary conditions were found to have no effect on the computed phase lag. The interface conductance between the transducer and the substrate was found to have some effect on the extracted thermal conductivity. The hyperbolic heat conduction equation yielded almost the same results as the Fourier heat conduction equation for the particular case studied. The numerically extracted thermal conductivity value (best fit) for the silicon substrate considered in this study was found to be about 82–108 W/m/K, depending on the pump and probe laser spot sizes used.
- 18 June 2020
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 13 (1) , 1-37
Development and Validation of a Model for Efficient Simulation of Freezing of Water in Large Tanks
Liquid water–urea mixtures are used in diesel vehicles for exhaust after treatment. In cold weather, the entire liquid may freeze and the process may span over a day. Traditional computational fluid dynamics and heat transfer (CFD/CHT) methodologies are impractical for modeling such freezing processes because of restrictions in the time-step size—typically milliseconds—posed by numerical stability and physical timescale considerations. Preliminary investigations revealed that the primary constraint for using small time-steps is the fine-scale motion generated by natural convection in both the liquid and the gas. A new model is proposed and demonstrated for efficient prediction of the propagation of the solidification front. In this model, heat transfer due to natural convection is modeled as a diffusive process analogous to how turbulent transport is modeled using an eddy diffusivity. The model enables the use of large time-steps since the fine-scale motions due to natural convection are not resolved. It was validated against experimental data for pure water, which were also collected as part of the study. Each experiment collected data at intervals of 6 s for a total duration of about 24 h. Several different tank fill levels were considered, and a good agreement with experimental data was noted, especially for shallow fill levels. Large-scale parallel three-dimensional calculations were conducted for the freezing of pure water in a few days of computational time as opposed to a year (projected) of computational time using traditional CFD/CHT models and the same computational resources.
- 18 June 2020
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 13 (1) , 1-37
Development and Validation of a Model for Efficient Simulation of Freezing of Water in Large Tanks
Liquid water–urea mixtures are used in diesel vehicles for exhaust after treatment. In cold weather, the entire liquid may freeze and the process may span over a day. Traditional computational fluid dynamics and heat transfer (CFD/CHT) methodologies are impractical for modeling such freezing processes because of restrictions in the time-step size—typically milliseconds—posed by numerical stability and physical timescale considerations. Preliminary investigations revealed that the primary constraint for using small time-steps is the fine-scale motion generated by natural convection in both the liquid and the gas. A new model is proposed and demonstrated for efficient prediction of the propagation of the solidification front. In this model, heat transfer due to natural convection is modeled as a diffusive process analogous to how turbulent transport is modeled using an eddy diffusivity. The model enables the use of large time-steps since the fine-scale motions due to natural convection are not resolved. It was validated against experimental data for pure water, which were also collected as part of the study. Each experiment collected data at intervals of 6 s for a total duration of about 24 h. Several different tank fill levels were considered, and a good agreement with experimental data was noted, especially for shallow fill levels. Large-scale parallel three-dimensional calculations were conducted for the freezing of pure water in a few days of computational time as opposed to a year (projected) of computational time using traditional CFD/CHT models and the same computational resources.