MIMichael Iza

Michael Iza

*This is an algorithmically generated author record based on publicly available information.

Michael Iza has a total of 41 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Low-droop and high-efficiency (>40%) UVA emitters enabled by precursor modulated quantum wells

    by Yifan Yao, Hanyu Bi, Ibraheem Aijarboua, Toru Inatome, Jiaao (Amy) Zhang, Michael Iza, Shuji Nakamura, Steven P. DenBaars

    We demonstrate a precursor-modulation growth scheme to overcome the efficiency limitations of ultraviolet-A (UVA) light emitting diodes (LEDs) caused by interface intermixing and poor carrier confinement. By incorporating intentional growth interruptions, we engineered more abrupt interfaces with Al-rich interfacial “spikes.” Scanning transmission electron microscopy energy-dispersive x-ray spectroscopy mapping and Schrödinger–Poisson simulations confirm these spikes increase conduction- and valence-band offsets by over 50%, improving electron–hole wavefunction overlap by approximately 20%. The resulting 380-nm micro-LEDs achieved a peak external quantum efficiency of 41%. Notably, the devices maintain high efficiency above 40% up to a current density of 200 A/cm2 with negligible droop. This approach provides a scalable and robust pathway for high-power, high-efficiency solid-state UVA emitters.

  • Monolithic transfer of thin-film micro-LEDs via electrochemical etching

    by Yifan Yao, Hanyu Bi, Toru Inatome, Stephen Gee, Michael Iza, Steven DenBaars, Shuji Nakamura

    We report a scalable, low-damage, and high-throughput process for monolithic transfer of III-nitride micro-LED arrays using selective electrochemical etching and wafer bonding. A highly Si-doped n-GaN sacrificial layer enables rapid and uniform release while preserving device integrity, resulting in atomically smooth lift-off surfaces suitable for subsequent processing. Fully fabricated vertical micro-LED arrays with mesa sizes from 100 × 100 μm2 down to 3 × 3 μm2 are released and transferred to silicon carrier wafers in a single step, maintaining precise spatial registration without conventional laser lift-off or serial pick-and-place methods. Transferred devices exhibit low reverse leakage, uniform current injection and emission, and enhanced optical output due to the thin-film flip-chip architecture, with minimal degradation in spectral performance. This approach provides a promising pathway for the scalable heterogeneous integration of III-nitride devices for micro-displays, optical communications, and sensing applications.


  • III-nitride thin film liftoff using electrochemical etching

    by Yifan Yao, Hanyu Bi, Toru Inatome, Ibraheem Aljarboua, Michael Iza, Steven DenBaars, Shuji Nakamura

    We report a selective electrochemical etching-based liftoff technique for III-nitride thin films using a heavily Si-doped sacrificial layer. This method enables the detachment of the millimeter-sized III-nitride thin films with tunable thickness from arbitrary substrates, achieving minimal damage and sub-nanometer liftoff surface roughness, offering more flexibility than traditional liftoff methods such as laser liftoff. Structure and optical characterization confirm the preservation of the crystal quality throughout the process. Notably, InGaN-based blue μLEDs were lifted off and transferred onto Si substrates, maintaining excellent optoelectronic properties, showing great potential in mass transfer of nitride-based μLEDs for micro-display. This proof-of-concept demonstration highlights a scalable, low-damage pathway for heterogeneous integration of III-nitride materials onto diverse platforms for advanced optoelectronic applications.


  • Structural and electrical properties of MOCVD-grown scandium nitride thin films on sapphire, Si, GaN, and SiC

    by Vineeta R. Muthuraj, Claire E. Vozel, Michael Iza, Abdullah Alharbi, Abdullah Almogbel, Shuji Nakamura, Umesh K. Mishra, Stacia Keller, Steven P. DenBaars

    Investigation of the growth and properties of binary ScN can aid in the understanding of its ferroelectric ternary alloys with GaN and AlN, but there are no existing data for ScN grown by metalorganic chemical vapor deposition (MOCVD). In this work, ScN growth by MOCVD was demonstrated using the Sc precursor (EtCp)2Sc(dbt). A broad range of growth temperatures, pressures, and V/III ratios were tested to investigate the impact of growth parameters on the properties of MOCVD-grown ScN. Approximately 100 nm-thick ScN films with growth rates from 0.06 to 0.20 Å/s were deposited on c-sapphire, (0001) GaN, Si-face 4H-SiC, and (001) Si. X-ray diffraction measurements showed that ScN films were solely (111)-oriented on both sapphire and GaN. Hall effect measurements revealed very high n-type electrical charge in the samples. The carrier concentrations of ScN on sapphire ranged from 2.1 × 1020 to 7.2 × 1020 cm−3, with electron mobilities in the range of 20–7 cm2 V−1 s−1. ScN films on GaN exhibited carrier concentrations from 9.6 × 1019 to 2.5 × 1020 cm−3 and electron mobilities from 42 to 8.5 cm2 V−1 s−1. The lowest sheet resistance of 45 Ω/□ (resistivity of 5.2 × 10−4 Ω-cm) was achieved for an ScN on sapphire film. These results indicate the potential for integrating ScN into the next generation of nitride electronics through MOCVD growth.


  • Open Access

    Advances in InGaN-based RGB micro-light-emitting diodes for AR applications: Status and perspective

    by Panpan Li, Jacob Ewing, Matthew S. Wong, Yifan Yao, Hongjian Li, Srinivas Gandrothula, Jordan M. Smith, Mike Iza, Shuji Nakamura, Steven P. DenBaars

    Micro-light-emitting diodes (µLEDs) are gathering significant interest as a technology for emerging micro-displays. However, µLEDs encounter numerous obstacles, including size-dependent efficiency loss, poor efficiency of red µLEDs, and challenges associated with the mass transfer and integration of full-color µLEDs. These issues become more acute in ultra-small µLEDs (<5 µm), which were required by the augmented reality (AR) displays. Here, we discuss the principal challenges faced by µLEDs and explore the possible solutions. We highlight recent advances in InGaN-based RGB µLEDs tailored for AR displays. In particular, we discuss the advancements in ultra-small InGaN µLEDs scaled down to 1 µm, the developments in InGaN red µLEDs, and the implementation of tunnel junction-based cascaded InGaN µLEDs for monolithic integration.


  • Open Access

    10.6% external quantum efficiency germicidal UV LEDs grown on thin highly conductive n-AlGaN

    by Michael Wang, Feng Wu, Yifan Yao, Christian Zollner, Michael Iza, Michael Lam, Steven P. DenBaars, Shuji Nakamura, James S. Speck

    We report on the material challenges of the growth of highly conductive n-AlGaN in germicidal ultraviolet light emitting diodes (GUV LEDs), with the degradation of the surface morphology of thick highly doped n-AlGaN due to the Si anti-surfactant effect. Threading dislocation inclination, increasing relaxation, and eventual cracking were observed with epitaxial n-AlGaN films thicker than 400 nm, along with an increasing Ga composition with the same metalorganic flows. With the optimization of the n-AlGaN conductivity in previous works, thin n-AlGaN films with high conductivity along with a smoothing superlattice were incorporated in GUV LED devices, resulting in LEDs with 285 nm electroluminescence, a low forward voltage of 4.2 V with a peak external quantum efficiency (EQE) of 10.6% and a peak wall-plug efficiency of 8.6% below 1 A/cm2, and an EQE of 5.5% at 20 A/cm2.


  • Open Access

    Structure of V-defects in long wavelength GaN-based light emitting diodes

    by Feng Wu, Jacob Ewing, Cheyenne Lynsky, Michael Iza, Shuji Nakamura, Steven P. DenBaars, James S. Speck

    The V-defect is a naturally occurring inverted hexagonal pyramid structure that has been studied in GaN and InGaN growth since the 1990s. Strategic use of V-defects in pre-quantum well superlattices or equivalent preparation layers has enabled record breaking efficiencies for green, yellow, and red InGaN light emitting diodes (LEDs) utilizing lateral injection of holes through the semi-polar sidewalls of the V-defects. In this article, we use advanced characterization techniques such as scattering contrast transmission electron microscopy, high angle annular dark field scanning transmission electron microscopy, x-ray fluorescence maps, and atom probe tomography to study the active region compositions, V-defect formation, and V-defect structure in green and red LEDs grown on (0001) patterned sapphire and (111) Si substrates. We identify two distinct types of V-defects. The “large” V-defects are those that form in the pre-well superlattice and promote hole injection, usually nucleating on mixed (Burgers vector b=±a±c) character threading dislocations. In addition, “small” V-defects often form in the multi-quantum well region and are believed to be deleterious to high-efficiency LEDs by providing non-radiative pathways. The small V-defects are often associated with basal plane stacking faults or stacking fault boxes. Furthermore, we show through scattering contrast transmission electron microscopy that during V-defect filling, the threading dislocation, which runs up the center of the V-defect, will “bend” onto one of the six {101¯1} semi-polar planes. This result is essential to understanding non-radiative recombination in V-defect engineered LEDs.


  • Effect of nucleation layer thickness on reducing dislocation density in AlN layer for AlGaN-based UVC LED

    by Muhammad Esmed Alif Samsudin, Yusnizam Yusuf, Norzaini Zainal, Ahmad Shuhaimi Abu Bakar, Christian Zollner, Michael Iza, Steven P. DenBaars

    Purpose: The purpose of this study is to investigate the influence of AlN nucleation thickness in reducing the threading dislocations density in AlN layer grown on sapphire substrate. Design/methodology/approach: In this work, the effect of the nucleation thickness at 5 nm, 10 nm and 20 nm on reducing the dislocation density in the overgrown AlN layer by metal organic chemical vapor deposition was discussed. The AlN layer without the nucleation layer was also included in this study for comparison. Findings: By inserting the 10 nm thick nucleation layer, the density of the dislocation in the AlN layer can be as low as 9.0 × 108 cm−2. The surface of the AlN layer with that nucleation layer was smoother than its counterparts. Originality/value: This manuscript discussed the influence of nucleation thickness and its possible mechanism in reducing dislocations density in the AlN layer on sapphire. The authors believe that the finding will be of interest to the readers of this journal, in particular those who are working on the area of AlN.


  • InGaN-Based Solar Cells and High-Performance Broadband Optical Coatings for Ultrahigh Efficiency Hybrid Multijunction Device Designs

    by R. M. Farrell, D. J. Friedman, N. G. Young, E. E. Perl, N. Singh, J. R. Lang, C. J. Neufeld, M. Iza, S. C. Cruz, S. Keller, et al.

    Efficiencies exceeding 40% have already been achieved with GaAs-based multijunction (MJ) solar cells. In this talk, we will discuss the unique advantages and challenges of fabricating hybrid InGaN-GaAs MJ cells for ultrahigh efficiency device designs.